S3B Chassis. SHARP DV-5450SC . IX1492BM processor, SDA-20 561.
To enter the service, you need to connect the terminal block VIDEO
(6) and (2). After that, push the MODE button on the remote control. There-SERV-
message. Then remove the jumper. The choice of adjustment of CH and CH +.
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]* * *
SC Chassis . Hold the key (CH +) and (VOL-) to the panel
TV turn the toggle switch network. Exit: (STANBY).
* * *
SP41 chassis. SHARP 21FN1. To enter the service menu
to determine the S1006 switch to position mode service. For
Output on the screen modes alternately push the button SMODE,
S-NORM on the remote control, changing the value on the control button up, down.
The values of the menu system:
1. SERVICE MODE - mode service.
2. CUT OFF BKGD MODE - mode cut-off background.
3. H-CENT50 X/15 - horizontal displacement (50 Hz)
4. H-CENT60 X/15 - horizontal displacement (60 Hz)
5. RF AGC h/63 -?
6. VCO h/63 -?
7. SUB CON h/127 - Contrast adjustment.
8. SUB COL h/127 - color adjustment.
9. SUB BRI h/127 - brightness adjustment.
10. SUB TIN h/127 -?
11. X SUB VOL - volume adjustment
12. RF SUB VOL h/127 - volume
13. BB CON h/127 - Adjusts the contrast of blue background
14. BB BRI h/127 - Adjusts the brightness of blue background
15. D-TRAP SINGLE (DOUBLE) -?
16. F-TRAP HIGH (LOW) -?
Where x - the parameter number given television, the number of second swing adjustment example: "HCENT50
5/15”.
* * *
Chassis SP-42M . The board machine switch S1001
Set in the position mode service.
To display on-screen modes alternately click on the S-MODE button on the remote control.
* * *
SP-51 chassis. SHARP 14 \ 21 JN1: When the input of the microcontroller
37 in the space of three adjacent periods should be able to level high, called up the service menu.
* * *
SP70 chassis. SHARP: 14/2UIM; 14R-SC . (Type switch
S1006 in the position mode of service.) Put the jumper promezhdu bus
5 Wee pin. 37 MK or service switch switch, located
on the board near the selector in position SERV.
Choose buttons
CH V option.
Buttons change the value of + VOL -.
Parameters are stored in memory automatically.
To quit the service to the TV switched to standby.
To adjust the white balance mode is RGB CUT elect.
Implements the remote adjustment buttons:
1 - increase the black level of R; 4 - lowering the black level of R; 2 - increase the black level G;
5 - lowering the black level G; 3 - increasing the black level B;
6 - reduction in the black;
7 - increase the amplitude of R; S - reduction of the amplitude R;
8 - the rise in amplitude, and D - reduction of the amplitude B.
* * *
SP70Shassi. SHARP: 14/2UIM; 14R-SC. (Enter the S1006 switch mode service.) Install Korotyshev between
+5 V bus and foot 37 MK or transferred service switch, located on the board next to
selector to position SERV.
Elect buttons CH V option.
Change the buttons + VOL - the parameter value.
Parameters are recorded automatically in the memory.
To exit the service have a television in standby mode switch.
The white balance adjustment mode is selected RGB CUT.
Adjustment performed by remote control buttons:
1 - increase the black level of R;
2 - increase the black level G;
3 - In the black-level multiplication;
4 - lowering the black level of R;
5 - lowering the black level G;
6 - lowering the black level B;
7 - increase the amplitude of R
8 - increase the amplitude of V;
S - reduction of the amplitude R;
About - lowering the amplitude B.
* * *
Service mode chassis UA-1 SHARP On the chassis UA-1 carried three models of vehicles SHARP, in the Russian market
submitted by: 21A1-RU 20A1 and-RU, 21A2 RU. The second of these, as its name
model significantly, applies to the value of CRT screen diagonal 20 "
and two others - 21. "The difference model 21A2-RU, reduced mostly to
application of the two heads of dynamic Instead of the one in the models and 21A1RU 20A1-RU.
The main feature of all three models is the use of integrated
ultra chip IX3368CE, encompassing both a control processor and video processor.
Consider the service mode chassis UA-1, which is used to adjust
and adjusting the sound and picture after the work
repair (change of control of the processor, volatile memory chips, etc.).
To enter the service mode of short duration (1 s) is bridged
a jumper between 124 and 122, located on the main board or
button press JWS remote staff. The microprocessor in this mode
service becomes which of the seven submodes is:
• AGC & GEOMETRIC
MODE,
• WHITE POINT ADJ MODE,
• SUB ADJ MODE,
• Y-DELAY ADJ MODE;
• OFFSET ADJ MODE;
• 1C OPTION MODE;
• MISC OPTION MODE
To transfer from one sub-modes to the second button is pressed CH DOWN / UP
Remote control or front panel. To select the desired sub-modes pressed the button
VOL DOWN / UP remote control or front panel. To select a submode
(See Table 1.) Apply button CH DOWN / UP remote or front panel.
With the VOL DOWN / UP buttons or remote control panel, change the front setting selected.
To exit the service again short-lived (1 s)
bridged bridges 122 and 124 together. The microprocessor thus returns to normal.
Initialize non-volatile memory chips.
The initial values of all stored in the memory chip
volatile and are recorded at the factory prior to it
(Tables 1 and 2). To restore the initial settings,
In particular, after the change of non-volatile memory chips,
perform its initialization procedure.
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]To do this, the jumper is bridged 122 and a 124mezhdu include machine
network switch S701, and after approximately 1 s after this
bridge opens. Control parameter values according to Table. 1.
Table. Two options presented, the user is available in the ordinary
mode system and their values after the initialization of the nonvolatile memory chip.
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]* * *
VP-2 Chassis. SHARP: VT-2128, VT-1428. In the standby button simultaneously shake CH + front panel button and POWER) on the front panel video recorder.
Parameter buttons select CH V.
A button is changing VOL V value.
Parameter is memorized automatically.
To exit the service on the remote control MENU button for shake button is put on duty POWER.
* * *