سرفس مود - FUNAI

[color=rgb(128, 0, 0)]FUNAI S2500
[color=rgb(0, 0, 255)]Log into the service mode:
expose the remote control, short shorted pins 2 and 16 m / s LC7461M,
the TV will switch FACTORY. Bust regimes utility menu: re-closure of the
same conclusions 2 and 16. Further sorting and storing the option TV
derive operational.

[color=rgb(128, 0, 0)]FUNAI S2900PF
[color=rgb(0, 0, 255)]Log into the service mode:
1)
The front panel control your TV, press and hold down the sound «Vol-»
as long as the volume indicator does not indicate the minimum.
2) Continue to hold down the button «Vol-» on the front panel, remote control button (+) (lower right).
3) You will see the letter «S», and left the current parameter and its value.
4) Press the «channel + / -» you can select the desired parameter
5) Press the «volume + / -» you can select the desired value for each parameter
[color=rgb(0, 0, 255)]Output: POWER button on the remote control

[color=rgb(128, 0, 0)]FUNAI MK7, MK8
[color=rgb(191, 0, 0)]CPU: R-514, R-584, L7PAL3RD
[color=rgb(0, 0, 255)]Log into the service mode:
Open the remote and close to each other 2 and 14 feet m / D6600A.
Button 6 "mode" PICTURE SELECT "switches the character - a graphical
display information OSD.
[color=rgb(0, 0, 255)]Output: POWER OFF

[color=rgb(128, 0, 0)]FUNAI MK10
[color=rgb(191, 0, 0)]CPU: L7PAL3RD
[color=rgb(0, 0, 255)]Log into the service mode:
Adjusting for Funai-MK10 can be done only with the remote control
teletext. To install the TV in service mode should be on the board
short-circuit test point "TP" Tagged FACTORY MODE until the screen
displays a red "F". Further pressing the select button on the remote
control programs:
1 - is a horizontal line, adjust the alignment.
2 - AGC (AGC)
3 - VCO (voltage-controlled oscillator)
4 - H POSI (Horizontal Alignment)
5 - L-STER (b), H-STER (R), H-STER (B), L-STER (R) adjustment of colors.
6 - Adjustment of static information-rays.
7 - Checking the purity of color (the illumination of the screen one of the primary colors)
8 - CUT OFF (cutoff level RGB)
9 - DRIVE (Span RGB)
0 - Set the brightness, contrast, saturation by default
VOL + - autosearch
DISPLAY - adjust brightness, saturation and contrast. Definition
SLEEP - Auto Search
0/AV - cubyarkost, subnasyschennost, subkontrastnost, subchetkost
PREVIOUS - AFT (AFT)
Parameter value change buttons + CH,-CH.
[color=rgb(0, 0, 255)]To exit the service mode press the button POWER. Adjust settings are saved automatically.

[color=rgb(128, 0, 0)]FUNAI MK11
[color=rgb(191, 0, 0)]CPU: LCB 863320A
[color=rgb(0, 0, 255)]Log into the service mode: in the native remote control button soldered between 2 and 16nogami m / s RT2461-103. Push the button
1-th time - on the screen: FACTORY
2 nd time - on the screen B / W ADJUST (reg. regimes CRT)
3rd time - ADJUST (geometry)
4-th time - SETUP (setup option)
5 th click - out of service
Buttons (P) (P +), (V-), (V +) setting the values ​​in the options.
[color=rgb(0, 0, 255)]Output: POWER OFF.

[color=rgb(128, 0, 0)]FUNAI 1400A MK12
[color=rgb(191, 0, 0)]CPU: L11PAL2ND, M372CH8-056FP, M3727GM8-061FP L11PAL 3RD
[color=rgb(0, 0, 255)]Log into the service mode:
To
use a conventional (N0121UD or N0134UD) remote control as a service,
perform the following steps: Unscrew the three screw from the rear panel
remote control, remove the panel and set the jumper "J1". To enter the
service mode include TV with main switch on the front of the TV and
press the button «SLEEP» on the remote. On the screen of the
microcontroller (eg: 056 displays the version 0.07). To save your
settings turned off and turn on the TV using the power switch.
Work:
Picture (bre, cnt, clr, tnt) VOL-: to switch other settings Prince and 2
... 9. At certain positions the buttons (VOL-) work 1.2.3. Adjusting
the values ​​knopkamimi (CH + \ -)
[color=rgb(0, 0, 255)]Output: POWER OFF

[color=rgb(128, 0, 0)]FUNAI MK11
[color=rgb(0, 128, 0)]Chassis 11AK30
To
activate the service mode, press the blue button on the remote. On the
TV screen should appear INSTALLATION menu. Then on the remote Repeatedly
press 4,7,2,5. Appears on the screen menu.
To select the required options click the button "P +" or "P", and to edit: "+" button or "-" on the remote.
Coloured
buttons used remote control in the service menu as follows. Red button
(only for stereo model) switches AVL is ON or OFF. Green button toggles
the aspect ratio (4:3 or 16:9). This is necessary when setting up the
vertical size in 16:9 mode. Yellow button turns on the Vertical scan
disable and is used when setting the accelerating voltage. The blue
button is used to automatically adjust the AGC and IF.

FUNAI SERVICE


Log "SERVISE": Close by a 2 and 14 feet in chips D6600A remote.
Button 6 mode "PICTURE SELEKT" switches the character - a graphical display information
OSD.

* * *

2100A MK10 HYPER


To install the TV in service mode, you need to short the circuit board test point TP with
Tagged FAKTORY MODE until the screen displays a red F.
Further pressing the remote button, select programs:
1 - is a horizontal line. Adjust the alignment.
2 - AGC
3 - VCO (voltage-controlled oscillator)
4 - Horizontal Alignment.
5 - Adjusting the color tones.
6 - Adjustment of static information-rays.
7 - Checking the purity of color (bitmap).
8 - Level cutoff RGB.
9 - The scope of RGB.
0 - Set the brightness, contrast and saturation settings.

* * *

2100A MK11


To enter the service in MK11 own remote control button solder between 2 and 16 feet m / c, PT 2461-103.
Push the button the 1st time - on the screen: FACTORY; pressure. 2nd time - on the screen B / W ADJUST (reg. FUNAI


CRT mode); third time - ADJUST (geometry) for the 4th time - SETUP (setup options) 5th Pressing

• out of service. Buttons P and P +; V-; V + help to establish the appropriate values ​​in the right places.
  

* * *

MK-12


In remote assembled on a chip 67N705zamknut third to second (ground) leg.
In their own designated jumper J1. Log SLEEP \ Exit STBY
Work: Picture (bre, cnt, clr, tnt) VOL-: to switch other settings
book-and 2.3 .. 6.8.9. At certain positions the book-and VOL-run 1.2.3.
Adjusting the values ​​of book-E CH + \ -


* * *

FUNAI LCD-A1504


How to initialize the LCD TV:
1. Turn the power on. (Use the main power on the TV
pcs.)
2. To enter the service mode, press the [STANDBY], [2]
[7], [1], [MUTE] buttons on the remote control
units in order for 5 seconds.

• To cancel the service mode, press the [STANDBY]
  

The buttons on the remote control.
3. To initialize TV LCD, press the "DISPLAY"
The buttons on the remote control.4. Confirm "indication FF" in the upper right
screen.

* * *

FUNAI TV1400 MK13 Hyper


Enter the service mode.
1) Press the button on the remote control MENU.
2) Press the button three times RECALL.

• To select the service mode menu (Factory1, Factory2, Factory3) consistently
  

press MENU.

• To select the submenu item, touch the button CH + / CH-.
  
• To adjust the selected item press the Vol + / Vol -.
  
• Adjusting some of the items automatically. Yellow symbol means that the adjustment
  

completed.

• To exit the service mode, press Recall again.
  

* * *

FUNAI TV-2500PF


On the remote, press the "RECALL", then press the "V-" and hold it for a while. Appears on the screen
"FACTORY". Repetition of this operation several times will lead to a
conclusion on the screen "C / B ADJUST" "ADJUST" "SETUP" and
return to "NORMAL TV".

* * *

FUNAI TVC-5044, FUNAI TVD-A2104PT


1. Turn the power on. (Use the main power on the TVpcs.)
2. Press [STANDBY / ON], [2], [7], [1], [MUTE] buttons
on the remote control, in that order within 5
seconds. When you enter the service mode, "4"
display at the corners.
3. During the service mode of electric restructuring
The mode can be selected by remote control key.

* * *

FUNAI MK11,

LC863320A -. To enter service in the remote native solder button
between 16 and 2 feet m / c, PT 2461-103. We press the button once - on the screen: FACTORY.
We press a second time - on the screen: B / W ADJUST (control regimes tube). third time
- ADJUST (geometry). fourth time - SETUP (setup options). Fifth squeezing -
out of service. Button V-; V +; P, P +, helping to establish the necessary values ​​in the appropriate places.

* * *
TV FUNAI TV-2500PF.


On the remote to press "RECALL", then push "V-" and
hold it a few times. Inscription on the screen "FACTORY" appears.
Repetition of this operation several times will lead to the removal of the screen "C / B ADJUST", then "ADJUST", then "SETUP" and will again return to "NORMAL TV".

* * *

TV Funai C2007 LCD.

Log in Service mode is similar to the model C1504 LCD:
connected, press the button on the remote stb, dial code 2,7,1 and mute hold more than 5 seconds.

* * *
TV Fusion FLTV-19W6 LCD.


Enter the service mode: button and menu code 7050.


* * *



TV GALACTIC 21G180,

mikroprotsessorTDA9381PS
TDA9351/N3/3/1977 CH6620 CH7771, ULF AN17823A, HR TDA78040,
TDKS BSC24-01N4014, PAL / SECAM. B / G D / K.
Entering the service menu: - Press Menu, then select the code 6483.

* * *

TV GROL GR2510,

AT SHASI 5800 A5R601-01
MULTI IS, NO TEXT, Ruska LANGUAGE IS, TDA9384PS/N2/3I VC12K0
CD1729 PHILIPS2000FM-OSD, TSD426 N2M4S. HR chip
TDA4863AJ, transistor strochnika C5148, tuner S221-389W14-01 XG6SV96A,
in the power supply 501265RF E26, SAW filters Q6259K, in the tuner chip LA79107, chip in the remote SC3010B.
Entering the service menu: press the button on the "SM", then "[+]"
and finally "CH I / II". To adjust the submenu press the numbers
channels. Exit from the service via a button "[+]"

* * *


TV Grundig ST70-2010

100 Hz TOP, 22.2 chassis. Memory 24c16. CPU SDA5555.
Log into the service menu on the remote home (TR160S) push i, MAIN MENU appears
code then dial 8 5 0 0. Txt quit the menu button. The service can be activated DK, NICAM.
Revised unit is not required.

* * *

TV GRUNDIG TVR3805,

memory 24C08, processor OEC0107B, STV2246C video.
Log into the service menu: Volume (-) to zero to hold,
then push the 9 button on the remote (kode 2027 MAK 2000), not letting Volume (-).
Exit button network!

* * *

TV HANSEATIC, DUAL, SCHNEIDER

: TV5504/20/25, TV-4 chassis, the processor: ST6385.
1) put pressure on the remote control while the blue and red buttons.
2) No later than five seconds, press the buttons at the same P + and VOL + on local keyboard TV.
Confirmation of entry will be the appearance on the screen:
SERVICE XXX (XXX symbols represent the control version of the program in the ROM of the processor located).

Application of the standard tuning control systems:
In the constant internal EEPROM memory of the processor saving data
White balancing and image geometry. In the case of a bad
setting or replacing the microprocessor may receive ST6385
need to use the standard settings in the program memory
mortgaged (ROM). There are two ways to use the standard settings.

1. The extension of the standard parameters in the RAM memory ROM:
Performing this operation must be done in the TV is off in the proper sequence:

• TV off from the network for a period of not less than five seconds.
  
• simultaneously push the buttons of P-and VOL + keyboard unit and connected to a network TV.
  

2. Use of standard data stored in the memory EEPROM:
In this case, the programs available in memory, the data standard
be incorporated into a permanent EEPROM, erasing the previous adjustment (setting). To realize this process, should:

• Jumper conclusions 5 and 9 on-board service on the back of the TV
  

located (jumper to ground output 37 ST6385 microprocessor).

• disconnect from the network TV for a period of not less than five seconds.
  
• push buttons on the P-and VOL + simultaneously keyboard and TV to connect to a network TV.
  

Adjust service:

• election options buttons P + / -.
  
• Adjusting the settings buttons VOL + / -.
  

Any adjustment is recorded automatically in the permanent memory channels.

Besides standard adjustment of balance, geometry, PTAs are also available:
CLDELAY - Luminance signal delay with respect to color.
PEAKING - Podregulirovka video channel features: In a typical test
signal, to bring the sharpness of the images to a small glut.
AFC - Podregulirovka characteristics of the circuit ARCz: this option
not subject to adjustment, it is used only during the installation of circuit characteristics ARCz _sm. a.
STEREOADJ - Adjusting the noise mezhdukanalnyh: At the output of wells
apply a test signal, including stereo (at frequencies different for both programs.) Connect the oscilloscope channel
to the outputs of the speaker, to obtain the minimum of interference regulate fonokanalami between the two.
OPTION - TV Set options: set according to Figure 1:.

Management process it is possible to access the options
TV configuration. Access to them (OPTION 1 ... OPTON 12)
buttons with VOL + / -. Selected option is turned on can be
ON or OFF is turned off by pressing the yellow. Unspecified
options, described in version of the program do not apply. To
return options set before, you must turn off the TV network of not less than five seconds.

There are versions of the control in the case TV-4 where
access to the options selected by means likely to command P + / -.
In this case, there is no need to turn off the TV for the return of
position of the original options. Change the options being implemented in
such a case, using the buttons VOL + / -, and storage options, an automatic way, and other adjustments.

The value of options:
If the option 7, TV to standby mode automatically
passes, six minutes after the shutdown of the program.
Otherwise, the TV will remain in operation, that
used practically in the course of making TV. From 12 options depends whether TV mode hospitality.
Attention! If the option 12, the TV programming is not possible.

a. Adjust the characteristics of the circuit ARCz:

• to get into the mode and option OPTION to choose options
  

5.vystavit (OPTION 5) - ON (AFC - disabled) and 6 (OPTION 6) - ON (AFC SERVICE - connected).

• from the generator to signal the test and get the best setup TV.
  
• In control mode, choose option AFC.
  
• screw the maximum core Fi 201 filter.
  
• unscrew the core, yet will not appear on the screen dividing the OSD,
  

green glow, and the cursor starts to slip in
center of the screen (if the division in yellow light, it means
that the adjustment range for the limit of the capture of the circuit goes).

• disconnect the unit from adjust mode.
  

check the serviceability of the SEARCH function (search)
If, despite the good signal, not adjusted TV, a procedure
repeat at the options, or set: OPTION 5 - OFF (connected) and OPTION 6 - OFF (disabled).
Exit from service: to put pressure on the TV remote control or turn off the TV.
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

* * *

Similar - GRUNDIG M70-580, M82-100, M70-100, M95-100. Chassis
CUC1860, CUC1880, CUC1835, CUC1890. Control processor
SDA30161 square on the panel (the board on the wall side of TV).
ROM 24S16 and 27S512, TDA4605, FEATURE BOX (on-board basic)
TDA9080, TDA8145, TEA8172, FA, Remote TP661 TOP, multiplier K536 = (HRT-402) HRT-906.
push and hold button (i) on the remote control, hold 10.5
seconds. At the same time can ignite a picture of mono (stereo). At
event tips - OK, get into - GRUNDIG Info Center, then in the Service programme
On SERVICE MODE line to press (OK) (8500).
Entering the Mode menu options Geometry - AUX, there is preservation.
To adjust the mode to remember the service, you need to pin 7 SDA3526 on housing plant.

* * *

TV GRUNDIG ST 70-2003

C7chassis. BEKO. ZX8.190-17.
Enter the service mode: Menu button and the code 8500.

* * *

TV HAIER. Model D29FV6.


Processor STV3500 G220H0426, block wells: TEDE9-276A. TDKS: BSC-0122B.
Composition of the chassis: HEF4053BP; LA75503; TDA7497; LA1116; KA7630
Digital module: K4S641632HTC75; STV2310-4; STV3500; STV6688-11; TA1370FG; M29KW016E.

Enter the service mode: This television - no remote control. To enter, you must: a working mode button V-volume reset to 0.
V hold - press the V + (so convenient that the buttons in the form of
planochki one) and hold for three seconds. All - we are in the service
menu!
Then remote control: button "menu" sections of service changes, P +,
P-navigate menus items, V-, V + change in the values ​​of parameters.
Exit - to move in the duty room. Memory - automatically saved.* * *
TV HANSEATIC, DUAL, SCHNEIDER: ST6714, TV M4055, CTV 2703, DTV-1 chassis, CPU: CCU 10, CCU 09 and CCU 13.



Digital TV DTV-based 1shassi, corporations SCHNEIDER.

1) At the same time push button S, on the local keyboard, the TV is located, and on the remote control button C.
Confirmation enter the service message will be: SEVICE MODE

Service adjustment:

• election parameters low tone buttons + / -.
  
• Adjusting the parameters buttons VOL + / -.
  
• Remembering the button T (IDEAL).
  

If the designation of controlled functions, the letter big small
It follows then that means that the adjustment is carried out accurately.
The emergence of large letters on the second place means that the adjustment clumsy.

• By clicking at the same time S button and TELETEXT, you can horizontally
  

adjust the position of text in TXT SERVICE MODE mode on the screen.
Before entering this mode should be in the position of TV is TV.
Adjusting the position of the text is being implemented buttons VOL +, VOL-,
and preserve the memory of the set of text buttons T.

Adjustable parameters like the DTV-2 chassis.

For the purposes of service may be necessary to conduct the following operations:

Locking System NTSC:

• Sign in service mode.
  
• push button + and low tones to choose Op2.
  
• push button 6 on the remote control.
  
• Save in memory of the results by pushing a button on the remote T.
  
• Exit the service by pushing the TV button on the remote.
  
• Repeatedly push a button on the remote control 6.
  

Activating blocking voltage, VCR switching (8 pin terminal SCART):

• Sign in service mode.
  
• push button and low tone-elect Op3.
  
• Press the button on the remote control 7.
  
• To memorize the results by pushing a button on the remote T.
  
• Exit the service by pushing a button on the TV remote control.
  
• Then press the button on the remote control 7.
  

Saving the memory size HUE (for the version of the processor CCU 13):

• push button T on the remote control.
  
• push a button on the keyboard MEMORY local.
  

Attention!
In the event of a change MDA2062-11 MDA2062-12 should remember that they
are not interchangeable! Each system appropriate designation is
written:

• IC1303 - MDA2062-12
  
• IC1302 - MDA2062-11
  

Incorporated adjustments made to the memory relating to television sets, which are provided with 21-inch CRT diagonal.
Analogue microprocessors CCU CCU 09 and 10 became 13 CCU processor.
However, if such a change is needed constant change memory MDA2062.
Table 1 shows the approximate values ​​of each
adjustments for different types of picture tubes, used in the TV DUAL: TV M4055 on DTV-1 chassis.
Exit from service: to put pressure on the TV remote control.


[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]


* * *

TV HISENSE TF2168H.

Processor - LA76936N SUSOC
7N-57V7, TUNER - FSTOK-3H3-H5-1 MEMORY - 24C08, ULF - LA4225, UPS - standard
"Chinese" 3-transistor TPI - 3DD5017, BCK-07-01CU (BCK-08 can-F404CU),
QUARTZ - 32.768 MHz and 4.433619 MHz, the IC CD - D78041, HOT - D5094 (No uverennnosti,
device after a failed repair, the customer brought the transistor), FBT - (BSC25-01N4035G)
BSC25-0234B, was replaced TDKS BSC25-01N40L ("native" could not be found -
replacement is not quite correct, the amount of disturbed horizontal),
remote control - HISENSE ES-21514A (IC Remote Control - CD7461G0)
Entering the service menu - the button hidden FACTORY (under the SLEEP button is located)

* * *