schematic-VIDEO CASSETTE-monitor-service manual SHASSIS Panasonic Philips SAMSUNG SANYO SHARP SONY toshiba Aiwa AKAI DAEWOO Goldstar HYUNDAI VIDEO Grundig Hitachi JVC LG Mitsubishi National NEC ORION VESTEL Corus-Repair-Plasma-LCD |
بسم الله الرحمن الرحيم اللهم صل وسلم وبارك على سيدنا ونبينا محمد صل الله عليه وسلم الرجاء من الجميع الدعاء لمدير الموقع بالرحمه والمغفره.
سبحان الله وبحمده .. لاحول ولاقوه الا بالله..لا اله الا انت سبحانك اني كنت من الظالمين .. اللهم صل وسلم وبارك على سيدنا ونبينا محمد صل الله عليه وسلم https://m.youtube.com/c/ashraf5914?reload=9&reload=9
|
| | جميع سرفس مود -AIWA | |
| | كاتب الموضوع | رسالة |
---|
MSA مشرف عام
عدد المساهمات : 541 تاريخ التسجيل : 16/06/2010
| موضوع: جميع سرفس مود -AIWA الثلاثاء مايو 03, 2011 2:52 am | |
|
AIWA 1402, 2002KE, 2102KE CPU: TVPO2066 D05/047 Log into the service mode: a button S009. Clicking on it simultaneously with a button (DISPLAY) on the remote control, enter the service menu.
AIWA TV-C142, TV-A215 Log into the service mode: press a hidden button on the remote, which is located between Knoop. "8" and SYSTEM (false panels under the console). Yield: click on a hidden button again
AIWA TV-A1419, TV-A2019, TV-A2110, TV-A2118, TV-A2588, TV-SA1251, TV-SE141, TV-SE211, TV-SX2150 Log into the service mode: button under raised panel desk. The first button "TEST" is the right of "0". The second is to the left of the button "SYSTEM"-button "FINISH" Press the "TEST" 1 time, with run mode "Aging mode". - Press the "CHANEL" that would enter in "Adjustment mode", this mode can be canceled.
AIWA VX-G140, VX-T147 Log into the service mode: 1) The sound level set to minimum. 2) Press and hold the VOLUME DOWN on the local keyboard. 3) Press the 9 button remote control. -You will see one of the six service sub-menu. Set Reg. parameters of the standard - AGC, geometry, balance, OSD. -Selecting a button ... 7 Remote Control. Button 7 - transition from dnogo submenu to another. -Changing the value of buttons, VOL UP / DOWN. Exit: Press the 8 button on the remote.
AIWA VX-G143 Log into the service mode: - Turn off the TV from a network of networks - Turn on the TV and set the sound to minimum. - Press and hold simultaneously more than 2 seconds, "VOL-" on TV and "9" RC. - The TV came in "Adjustment mode"
AIWA TV-A2110/15/18 CPU: TMP87CP38N-xxx. All adjustments in the service mode, performed with a standard remote control-type RC-6VT06, which includes supplied with models TV-C142/86-LB4-951-010 firm AIWA. Mode Aging Mode is used in the manufacturing process to heat and adjust the TV. During the operation, In this mode, you can determine the correct tuning of the AFT, as well as to determine the actual operating time TV, the function of HEX. Log into the service mode: 1) Turn on your TV. 2) Press the TEST button remote control (hidden under the false panel) window will appear In the Aging Mode TV can be operated without power at its input a signal, in this case, you must click Auto Power Off. If on the contrary AFT setting will display IN, this means that the setting is optimal. The appearance of the inscription HIGH or LOW indicates the frequency deviation up or down accordingly. Inscription OUT means no input signal at the antenna socket. Time value of TV (HEX) is displayed in hexadecimal form. In case of exceeding the value 7FFF (32,768) is auto zeroing counter. If you want to forcibly reset the counter, click FINISH remote. Adjustment in service: -Press the TEST button remote control. TV enters the regime Aging Mode. -Select the adjustment menus buttons CHANNAL UP / DOWN. This will display the appropriate menu Where 14 - number of positions Reg. parameter. H POS - name. OA - the parameter value. -Choice Reg. option buttons CH + / CH-remote. -Change the values by pressing VOL + / -. -Button 0 disables the vertical scanning (used in ref. Accelerating voltage). Parameters, adjustable in the service mode: (in parentheses are the values of the parameters for the model of TV-A2115). If any adjustment function is absent, for example - H SIZE (item 28), then this parameter should be set to 00. Attention! In the model of TV-A2115 there is an option, system configuration, TV. To activate it follows in the mode of Aging Mode, press AV MODE. A window will appear -If you must modify the existing configuration of the TV, you should press button 8 (SH4). Displacement from 0 to F and back is button CH + / CH-. -Changes in the values of units buttons VOL + / -. - Storing click TEST. Exit: Turn off the TV from a network.
| |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: جميع سرفس مود -AIWA الثلاثاء يوليو 19, 2011 7:49 am | |
| AIWA
AIWA SERVICE
AIWA 1402, 2002KE, 2102KE
CPU TVP02066 D05 \ 04: Input 7 processor TVP02066 controls the switching in the service menu. The board staff is normally open-loop button «S009», if you click on this button together with the call button on the remote apparatus, it will input the Tools menu. If the buttons are not close to the body and vyv.7 simultaneously press the «DISPLAY» on remote. The family of vehicles "Aiwa 1402, 2002, 2102ya - one of the first representatives of the television technique of the middle class, where it first was used by the digital television signal processing (Except radio). Digital signal processing unit of the apparatus has only three chips: IC701 - performs basic signal processing, IC703 - has a control processor, IC706 - deco der SECAM. Digital hub manages the main processor IC001. Mode settings of the device are stored in the memory chip IC002. On the chassis of the machine is only two variable resistors: VR101, regulating the level of
| |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: جميع سرفس مود -AIWA الثلاثاء يوليو 19, 2011 7:51 am | |
| AIWA
AGC, and VR301, regulatory centering images vertically. Most of the customization of devices - the correction of the raster mode decoding of color, para- Meters images, etc. - can be done in service mode. At the same time strongly simplifies the process of adjusting apparatus as in their manufacture, and in the process operation, especially after the repair or replacement of individual components unit. To enter the service menu, the Control Point device solder button Contactor (vyv. 8 * microcontroller IC001 type TVP0266D05/04 for housing). Unit is turned off press the button again established closer and keep it as long as you do not press the call button on the remote control (RC). On display unit label should appear in "SERV", which indicates the occurrence of the machine service mode. Choose the appropriate option button + P, the value of the parameter set buttons + VOL-. To memorize the setting press the button on the remote control P <->. You will see the device must first appears in "MEMO" and fade over time, indicating that binge- | |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: جميع سرفس مود -AIWA الثلاثاء يوليو 19, 2011 7:52 am | |
| AIWAMinani newly introduced parameter. To exit the service mode seeking with KNO Gen. + P appears on the device label "SERV", and then press the power button device. 1.Nastroyka raster geometry Enter the service menu, the + P option is selected the settings screen its value using + VOL-. Serves on the screen device a test signal. If the value of the service was a step changed, it is necessary to remember exactly at this point. This mode is suitable for NVM. 2.Izmenenie signal processing parameters Enter the service menu and the + R-configuration mode is selected NVM. Then the buttons on the remote control 7.8 set the right address, but the buttons + VOL-, O, 1, 9, change it content. The values of the addresses and their contents are given in hexadecimal. * * * [b> AIWA TV-A215, TV-C142: CPU M37220M3-150S. To activate the test mode Click on the hidden button on the remote control buttons located between 8 and SYSTEM. (under false panels) | |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: جميع سرفس مود -AIWA الثلاثاء يوليو 19, 2011 7:53 am | |
| AIWA[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]To cancel the test mode, use the same button again. After replacing memory chips to perform the following. Use the remote-type RC-6VT06. 86 - LB4-951-010 1. Press the TEST button to activate the service mode. 2. Press DISPLAY on the remote control, and make sure that the screen such as in Figure 1. [ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]Fig. 1. 3. Press the CHANNEL button on the remote control, then move the red marking on the K3 Set the data as in Figure 2 with the buttons VOLUME +, - [ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]Fig. 2. 4. Then move the cursor to the K4 and set the data as ris3 [ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]Fig. 3. 5. Press DISPLAY, then press FINISH (hidden under the false panels) 6. After appearing on a few seconds the message is automatically powered INITIAL off. Log in TEST MOD-mode on the TV press + and - buttons, hold them to include | |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: جميع سرفس مود -AIWA الثلاثاء يوليو 19, 2011 7:53 am | |
| AIWA
TV. Exit - click for POWER. * * *
AIWA TV-C1400 (CP-005)
1. Click the 91st channel. 2. Sharpness - output to 0. 3. Click the button on the remote in this order: Skip (R) - Move (G) --- Menu This opens the service menu * * *
AIWA TV-F21TS1B/F21TS1E/F21TS1K/F21TS1U
This includes self-diagnosis mashines. If an error occurs in the standby mode (1) LED will blink automatically. Description of self-diagnosis function is in the manual. Standby light blinks a certain number of times, which translates as the likely source problems. The remote control can be used for data analysis. 1. DIAGNOSTIC INDICATORS When errors in the standby LED will blink a certain number of times to indicate the possible cause defect. If you have more than one error, then the indicator will determine the first area of concern. The results for all subsequent elements of the diagnosis on the screen. It is not considered an error if the screen displays "0".
| |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: جميع سرفس مود -AIWA الثلاثاء يوليو 19, 2011 7:54 am | |
| AIWA
3. Stop in standby mode. Turn off the power switch on the TV or unplug the power cord to go into standby mode. The LED flashes. 4. Self Screen Display The mistakes with symptoms such as "sometimes turns off the machine" or "sometimes the screen goes blank," which could not be confirmed, You can bring up past instances of failure to screen for confirmation. [Ensure the screen test] In standby mode, press the button on the remote control sequentially in rapid succession, as shown below: Display / Channel 5 / Volume / Power / TV
3-1. CORRECTION Adjustments to this model can be made using the supplied remote commander RM-Z5200. A. ENTRY Service Mode With the device in standby mode, press the following sequence of buttons on the remote control. 'TT - -' appears in the upper right corner of the screen. Other information on the status will be displayed. B. Press "Menu" button on the remote control to get the service menu on the screen. | |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: جميع سرفس مود -AIWA الثلاثاء يوليو 19, 2011 7:55 am | |
| AIWA
GEOM WHBL SADJ YC SYNC PICT SW VIF C
. The screen shows only 8 points at the same time. To switch to the corresponding item switch the channel buttons up and down.
D. Press the left / right button or ENTER button on the remote control to enter the desired item.
* * *
AIWA TV-F2400
3-1. Entering the service menu. Adjustments to this model can be established via the supplied remote commander RM-Z5200. A. INPUT in Service Mode With the device in standby mode, press the following sequence of buttons on the remote control. 'TT - -' occurs in the upper right corner of the screen. Other information on the status begins to appear. B. Press "Menu" button on the remote control to get the service menu on the screen. GEOM WHBL SADJ YC SYNC PICT SW VIF C
. The screen shows only 8 points at one time. To go to the application of the relevant item up and down buttons | |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: جميع سرفس مود -AIWA الثلاثاء يوليو 19, 2011 7:55 am | |
| AIWARemote control. D. Press the left / right button or ENTER button on the remote control to enter the desired item. * * * AIWA VX-G140, VX-T147, percent.: OEC6044D. Programming Flash memory: When replacing the permanent memory, it is desirable to use pre-wired m / c,. Required initial installation of certain memory cells are made as follows: 1) Press and hold the VOLUME DOWN keys on the local TV. 2) Press the 6 button remote. On the screen there message: INIT 01 CB where 01 - a cell address; CB - cell data.
- Press the SET + or SET-, alternately selected memory cells with addresses 01 ... 63 (position
cell address is blinking).
- Press ENTER to enter the cell data (position data pulses).
- Press SET + or SET-enter such data values:
01-CB 22-00 43-3A 02-91 23-00 44-80 03-09 24-04 45-80 04-80 25-FF 46-80 05-88 26-1F 47-00 06-AD 27-00 48-00 07-00 28-EE 49-FF 08-00 29-E5 50-50 09-00 30-7B 51-0F | |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: جميع سرفس مود -AIWA الثلاثاء يوليو 19, 2011 7:56 am | |
| AIWA10 - 00 31-4F 52-1D 11-00 32-20 53-1D 12-00 33-4B 54-05 13-00 34-17 55-BA 14-00 35-53 56-80 15-00 36-60 57-0E 16-00 37-0A 58-54 17-10 38-00 59-00 18-00 39-08 60-00 19-00 40-C2 61-00 20-00 41-80 62-00 21-00 42-80 63-21
- Press ENTER to move to the next memory location.
- Memory write - put the television in STAND BY.
Attention! The process of programming the memory is reset to zero at the time the TV. For this TV should be turned off for 30 minutes, removing the plug from the outlet or discharge the capacitor C101, TV disconnected. Enter the service mode is possible in step - Warning! : 1) The sound level at least clean. 2) Press and hold the VOLUME DOWN on the local keyboard. 3) Press the 9 button remote control.
- You will see one of the six service sub-menu. Set Reg. standard settings - AGC
geometry, balance, OSD.
- Selection of parameters of buttons 1 ... 7 Remote Control. Button 7 - transition from dnogo submenu to another.
- Changing the value of the buttons VOL UP / DOWN.
| |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: جميع سرفس مود -AIWA الثلاثاء يوليو 19, 2011 7:57 am | |
| AIWAExit from service: Press the button on the remote control 8. * * * TV-A2110, TV-A2115, TV-A2118. Processor - TMP87CP38N.Pult - RC-6VT06.Nazhat button «TEST» on the remote. Output - off switch. VX-G140, VX-T147.Protsessor - OFC6044D. Remote control - staff. Log in service is possible with zeroed counter-time TV. To do this, turn off the machine for 30 minutes .. Log necessary set the sound to a minimum, press and hold the «VOLUME DOWN» on the front panel, then press "9" on the remote. Exit - Press "8" on the remote. VX-G143 Entry into service is performed as follows:
- Excluded from the net on 35 minutes.
- Enabled device and set the sound to a minimum.
- Pressed simultaneously for more than 2 seconds VOL-on TV, and 9 on the remote.
- vehicle entered the "Adjustment mode"
* * * AIWA: TV-A2110/15/188, Cent.: TMP87CP38N-xxx. All adjustments in the service mode, are made with a standard remote control RC-type 6VT06, which included models of the firm TV-C142/86-LB4-951-010 AIWA. | |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: جميع سرفس مود -AIWA الثلاثاء يوليو 19, 2011 7:57 am | |
| AIWAMode Aging Mode: Aging Mode Mode is used in the production process to adjust the heating and TV. In during the operation in this mode, you can define the configuration of features AFT, and also determine the actual operating time TV function HEX. 1) Turn on your TV. 2) Press the TEST button remote (hidden under the false panels) On-screen window will appear. In the Aging Mode TV can be operated without power at its input a signal, in this case should press the Auto Power Off. If the opposite occurs AFT setting inscription IN, this means that the setting is optimal. The appearance of the inscription means HIGH or LOW frequency deviation vverz or down accordingly. Inscription OUT means the absence of an input signal to the antenna jack. The value of TV time (HEX) is displayed in the form of schestnadtsaterichnoy. In case of excess value 7FFF (32,768) is avtoobnulenie counter. If you need to force reset counter, click FINISH remote. Adjustment in service:
- Press the TEST button remote control. TV enters the regime of Aging Mode.
| |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: جميع سرفس مود -AIWA الثلاثاء يوليو 19, 2011 7:58 am | |
| AIWA
- The choice of the adjustment menu buttons by CHANNAL UP / DOWN.
On the screen there a corresponding menu, such as _ris. 3. Where 14 - number of positions Reg. parameter. H POS - name. OA - the parameter value.
- Choice Reg. option buttons CH + / CH-remote.
- Changes in the values by pressing VOL + / -.
- Button 0 disables the vertical scanning (used in ref. Accelerating voltage).
The parameters controlled in the service mode: _ris. 5 (in brackets the values for the model TV-A2115). If any adjustment function is absent, for example - H SIZE (item 28), then this parameter must be set to 00. Attention! In the model of TV-A2115 there is an option, system configuration, TV. To activate it necessary, in view Aging Mode, press AV MODE. On the screen there _ris window. 4.
- If you need to make changes to the existing configuration TV, just press the button 8 (SH4).
- Displacement from 0 to F and back buttons is CH + / CH-.
- Changing the values systems buttons VOL + / -.
- Storing click TEST.
| |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: جميع سرفس مود -AIWA الثلاثاء يوليو 19, 2011 7:58 am | |
| AIWA
Exit from service: Turn off the TV from a network.
* * *
AIWA TV-SE211EH.
To enter the service menu using buttons of the remote, which are hidden under the false panels console. Button first "TEST" on the right sought to "0". The button second from the left sought buttons "SYSTEM", and this is a button "FINISH" To enter: - push "TEST", starts with the mode of "Aging mode". Push "CHANEL" to get into the "Adjustment mode", a mode for setting.
* * *
TV AIWA: TV-A2110/18/15,
Processor: TMP87CP38N-xxx. All adjustments in the service mode, make using the model Remote control type RC-6VT06, which is a set of delivery models TV-C142/86-LB4-951-010 Corporation AIWA. Mode Aging Mode: Aging Mode Mode is used in the manufacturing process to heat and adjust the TV. In the process, in this mode, define be faithful to set the function AFT, as well as the actual time the TV to determine, HEX function. 1) Turn on the TV. | |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: جميع سرفس مود -AIWA الثلاثاء يوليو 19, 2011 7:59 am | |
| AIWA2) push button remote TEST (hidden under false panels). On-screen window will appear. In the Aging Mode TV can work without submitting it to the input any signal, in this case should push the button Auto Power Off. If an inscription IN AFT setting is displayed, it indicates that setting the best. The appearance of signs or LOW HIGH indicates frequency deviation up or down accordingly. The inscription indicates no signal OUT at the antenna input. The period of the TV (HEX) is reproduced in hexadecimal form. In the case of the superiority of the value 7FFF (32,768) avtoobnulenie count performed. If you need to reset the counter force, push the button FINISH remote. Adjustment in service:
- push button TEST remote. TV mode Aging Mode will.
- adjustment menu selection buttons being implemented CHANNAL UP / DOWN.
On the screen there the menu corresponding to where the 14 - position number of adjustable parameters. H POS - his name. OA - the value of the parameter. | |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: جميع سرفس مود -AIWA الثلاثاء يوليو 19, 2011 8:00 am | |
| AIWA
- The choice of the controlled parameter buttons CH + / CH-remote.
- Change of the buttons VOL + / -.
- Button 0 disables the vertical scanning (used with an accelerating voltage regulation).
The parameters in the service mode adjustable: _ris. 5 (in brackets are values of the parameters for TV-A2115modeli). If there is no any adjustment function, for example, - H SIZE (item 28), then this parameter should be set to 00. Attention! In TV-A2115 model option is available, the TV system configuration. To activate it is to be in the mode of Aging Mode, push button AV MODE. On-screen window will appear.
- If you need to make changes to the configuration of the existing TV, must push button 8 (SH4).
- transfers from 0 to F and back buttons committed CH + / CH-.
- Changes in variables setting buttons VOL + / -.
- Writing to memory buttons TEST.
Exit from service: disconnect from network TV. * * * TV AIWA: VX-T147, VX-G140, Processor: OEC6044D. Programming the memory constant: | |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: جميع سرفس مود -AIWA الثلاثاء يوليو 19, 2011 8:00 am | |
| AIWAIf you change your permanent memory, it seems necessary to use pre-wired m / c,. Initial setup required a specific memory cells are produced as follows: 1) push and hold the VOLUME DOWN button on the keyboard, the local TV. 2) push button remote control 6. On the screen there message: INIT 01 CB where means: CB - cell data, 01 - cell address.
- pressing button SET + or SET-, alternately selected memory cells
with addresses 01 ... 63 (flashing position of a cell address).
- to press the ENTER button to transfer to the cell data (position data pulses).
- Press SET + or SET-enter the following data points:
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
- push button ENTER to go to the next memory location.
- memory is in progress - TV STAND BY move.
Attention! The programming procedure is performed in memory reset the counter time TV. To do this, turn off the TV should be for 30 minutes, pulling the plug from the outlet or S101razryadiv capacitor, switched off TV. | |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: جميع سرفس مود -AIWA الثلاثاء يوليو 19, 2011 8:01 am | |
| AIWALog into the service menu can execute a statement - Attention! : 1) The sound level at a minimum install. 2) push and hold the VOLUME DOWN button on the keyboard LAN. 3) push button remote 9.
- The screen seems one of the six sub-suppliers. A set of standard adjustment parameters - geometry, balance, AGC, OSD.
- Selection of parameters of buttons 1 ... 7 Remote Control. Buttons 7 - transition from one submenu to the second.
- Change the value of the parameter buttons VOL UP / DOWN.
Exit from service: push button 8 on the remote control. * * * | |
| | | | جميع سرفس مود -AIWA | |
|
مواضيع مماثلة | |
|
| صلاحيات هذا المنتدى: | لاتستطيع الرد على المواضيع في هذا المنتدى
| |
| |
| |
|