schematic-VIDEO CASSETTE-monitor-service manual SHASSIS Panasonic Philips SAMSUNG SANYO SHARP SONY toshiba Aiwa AKAI DAEWOO Goldstar HYUNDAI VIDEO Grundig Hitachi JVC LG Mitsubishi National NEC ORION VESTEL Corus-Repair-Plasma-LCD |
بسم الله الرحمن الرحيم اللهم صل وسلم وبارك على سيدنا ونبينا محمد صل الله عليه وسلم الرجاء من الجميع الدعاء لمدير الموقع بالرحمه والمغفره.
سبحان الله وبحمده .. لاحول ولاقوه الا بالله..لا اله الا انت سبحانك اني كنت من الظالمين .. اللهم صل وسلم وبارك على سيدنا ونبينا محمد صل الله عليه وسلم https://m.youtube.com/c/ashraf5914?reload=9&reload=9
|
| | سرفس شامل أجهزة service-mode CHINA | |
| | كاتب الموضوع | رسالة |
---|
أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: سرفس شامل أجهزة service-mode CHINA الثلاثاء يوليو 19, 2011 8:37 pm | |
| CHINA SERVICE 1. Log in services TFT TV SUPER, MIYOTA, OPERA, WARON and others on the CPU LC863320A, LC863324A, LC863328A, LC863332B - on the remote there are a few hidden buttons. To reach them, you need to peel top film. To enter - exit the service menu button is used as a signed (PROD). Management of CH +, CH-, VOL-, VOL +. The menu has three submenus with extensive settings. 2. 1. Volume at least 2. Press Volume - on TV and Recall on the remote 3. Timer, Timer, Mute - choice of menus Clarification: Using the remote control, press (RECALL (DYSPLAY)), then press the (V-) and hold it for a while. The screen will be 'FACTORY'. Repetition of this operation several again will display the 'C / B ADJUST' 'ADJUST' 'SETUP' and return to the 'NORMAL TV'. 3. Click on the RC: SKIP. - V. AFT. (Or - / -) * PIC output. 4. With remote dial: (MENU) (MENU) (V. WIEV) (MUTE) (SLEEP) - turning the pages. CPU TV SET will go to factory mode. Press "TIMER" key to go to the nextfactory menu.5. Close 2 and 13 (14) feet to the remote IP (chip can be potted). 6. IMS in the compound on the remote. Log in to the service - 2 and 15 feet of IP or close contacts at the upper half button 5 and the lower half below the button (the speaker is drawn). Appears "LA76810 option menu 00." In this position, the transition through the pages of the menu button "Volume +". Total 4 pages. There is an entry for Products in the compound, which is located directly on the card remote control. Her legs apart, like a spider, left and right. Above it is a small patch of contacts. Method of selection found a couple that needs to be close to the entrance to the service. Where they are words can not describe, I can only say that one pyatachek located to the left of IC, and other rights. 7. Hidden button closes the findings of 16 and 2 IC remote control (I have it implemented in the remote 52N8 for LC863532. Start counting from the top left display. Thick tracks - counts as 2 O, ie close second account from the top left and the fourth from the bottom right). When you click on the displayed FACTORY, followingPress - Balance menu, the next push - the next push - menu adjustable geometry ADJUST MENU 0. In the circuit ADJUST MENU 0 2 and 17 feet (also a hidden button in normal mode she ZOOM) displays ADJUST MENU 1 option SETUP SELECT to transfer mode ON. Each successive Pressing ZOOM (2-17) iterates through service menu from 9 to 0. Selecting options P +, P-, change V +, V-. Output - button 2-16. 8. LC863320A - FUNAI MK11. To enter the service in his native remote control button solder between 2 and 16 feet m / c, RT 2461 - 103. Push the button the 1st time - on the screen: FACTORY. Pressure. 2nd time - on the screen: B / W ADJUST (reg. modes tube). 3rd time - ADJUST (geometry). 4th time - SETUP (setup options). 5th Press - out of service. Buttons P and P +; V-; V + help to establish the appropriate values in the right places. ) 9. If it does not help - the universal remotes. 10. Removing the lock in these chassis - press and hold the DISP button on the remote control for 5-10 sec.) If there is no remote control - insert net IC memory, a TV run, shoot and write with her first place in the old firmware (inthe removed IC). For more information on PMI remote control: PT 2461-103 (apparently it is a direct analog SC7461 - 103, just a different manufacturer). She has a matrix 4 of 8 (4 - 8-input gate. O), a total of 32 combinations. You can search for untapped. Another chip allows three commands by double-clicking keys on a 5-door (in the matrix is 20 21 20 22 20 23). If the desired code located on the current page, the search does not take much time, because 20 combinations have already been used. And yet, in recent years (that I met) - marking the body panels from the top often corresponds marking of the processor (the last 4 digits, for example, LC863332A - 5Z51: Remote 5Z51), which is indirectly suggests that this type of panel will work with this processor.
* * *
عدل سابقا من قبل أشرف عثمان في الثلاثاء يوليو 19, 2011 8:56 pm عدل 1 مرات | |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: سرفس شامل أجهزة service-mode CHINA الثلاثاء يوليو 19, 2011 8:41 pm | |
| LC863322B (53W3 4F05) + LA76810A + LA7642 (Sesam) + AN (CS) 5265 (two VLF) + 24S08. at the entrance to the service (in the remote cap-la, there are hidden buttons - a triple click on one of them and we ADJUST MENU) menu sections responsible for any adjustments except for the geometry and something in color, could not be opened(To switch the mute button MUTE) * * * LC863328A - 5W63One version of the service entrance to the TV - the volume to 0 on the panel and RECALL on the remote. The second - a hidden button on the remote. * * * LC863332A-5Z51LC863332A-5Z51 - ERC 21SP50 (CE2181) (analog FUNAI S2100PF, S2500PF) - remote: RSU21SP50. Log into the service menu: Using the remote control, press (RECALL (DYSPLAY)), then press (V-) and hold it for a while. The screen will be 'FACTORY'. Repetition of this operation multiple times will display the 'C / B ADJUST' 'ADJUST' 'SETUP' and return to the 'NORMAL TV'. Removing the lock - on the remote press and hold CALL nearly a minute. Log in to s / m 2-16 pin CD7461CO (hidden button). Each time you change the circle: FACTORY - B / W BALANCE
- ADJUST MENU 0 - TV. Switching ADJUST MENU (0 - 9) closure 3 - 15 pin.
* * * LC863332B-53W31. Call MENU and type in 8633. 2. Call MENU and type in 8600.3. Log in for service LC863328-5W63, Mak maXim code 1 3 7 9 press VOL-on TV to 0, and Title on the remote. * * * LC863440W-52F2Service, for the lazy: Press MENU on the remote control at the same time and VOL + on the panel. * * * LC863448S-55S6Sanyo CE 14SA4R (Kaliningrad, 2005): CPU - LC863448S-55S6, S / P - LA76818A + LA7642N; VLF - LA4266; KR - LA78040; NOTES - TT2138; RCU - JXMYA (with none of the above is not compatible - ICs in the remote control - M055155 (5031A) - 20-Nogai planarka). Log in Service: Hold «MENU» (on the remote) and press the «VOL +» on TV. Flipping through the options buttons «TIMER» and «MUTE» on the remote control, change settings - «VOL-» and «VOL +». Options service from 00 to 93 - are clear and without manual, and then immediately goes to 300 transition option, etc. - And in them "?". TV came with a diagnosis - not working video input. Troubleshooting - go into service in "87" option (87 AV123) switch the value from "0" to "1", and then to exit the service click on the remote control «MENU» and turn off the TV Network button. After inclusion - options to come into force.* * * LC863532C-55R9Remote 2Y29, in a drop shaped pads are visible but they switched the sound. entered the service of closing the two left upper contact, and 4 lower right. At 14, the sheet 1 and put all the telly works. * * * LC863548B (36pin) +24 C16Log in servic - turn down the volume on the muzzle to zero, while holding, press DISP (pryamoug. plus) on the remote. Available versions ENTRY SERVICE: 1. Entry into service LCD TV SUPER, OPERA, MIYOTA, WARON and others on CPU LC863320A, LC863328A, LC863324A, LC863332B - several There are hidden buttons on the remote. To achieve up to them to peel foil top. To enter - exit the service apply button, inscribed as (PROD). Management VOL-, VOL +, CH +, CH-. The menu has three submenus with lengthy settings. * * * Method 2. 1. Volume at the very least 2. Push Volume - by Recall the TV and the remote control 3. Timer, Timer, Mute - menu selection Update: using the remote control to press (RECALL (DYSPLAY)), then push (V-) and hold it a few times. On screen, there inscription 'FACTORY'. Playing several times this operation will lead to the removal of the screen 'C / B ADJUST', 'ADJUST', 'SETUP' and return to the 'NORMAL TV'. * * * 3. Pressure on the RC: SKIP, then-V, on AFT, more (or - / -) * PIC output. * * * 4. Score from the panel: (MENU) (MENU) (V. WIEV) (MUTE) (SLEEP) - Page leaf. CPU TV SET transition to the service menu. Press "TIMER" button to enter the following service menu. * * * 5. Jumper 2 and 13 (14) The findings of the IP remote control (IC compound can be filled). * * *
عدل سابقا من قبل أشرف عثمان في الثلاثاء يوليو 19, 2011 8:58 pm عدل 1 مرات | |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: سرفس شامل أجهزة service-mode CHINA الثلاثاء يوليو 19, 2011 8:43 pm | |
| 6. PMI on the remote control in the compound. Entry into service - 2 and 15 EC or the conclusions jumper contacts for the upper half of buttons 5 and a half lower a button (the speaker is drawn). There will be a sign "LA76810 option menu 00. "In the position of the transition through the pages of the menu buttons "Volume +". Only four pages. There is an entry for drenched chips, which is located directly on the PCB panel. Feet apart from her, like a spider, right and left. Above it is small patch of ground contact. Way of selecting a pair found that need jumper for entry into service. Where they are located, not to describe words, I can only say that a penny is left of the IC, the second right.
* * *
7. The button is hidden, bridged two ends 16 and IC REMOTE (I realized this 52N8 remote for LC863532. Start counting from the top left display. Thick track - count as two outputs, ie bridged to the left second in a row at the top and bottom right of the fourth). When pressed FACTORY displayed on the screen, click the following - menu-balance, click next - click next - ADJUST MENU 0 adjustment menu geometry. In the ADJUST MENU 0 2 Bridging and 17 pins (also button hidden in normal mode, it ZOOM) on the screen displays ADJUST MENU 1 SETUP SELECT option to move the mode ON. Any subsequent press buttons ZOOM (2-17) goes through the menu service from 9 to 0. Election options P + P, the change in values V +, V-. Exit - buttons 2-16. 9. If it does not help - the universal remotes.
* * * 10. Removing the lock chassis in the data - to put pressure on the remote control and hold button DISP in the course of 5-10 sec.) If there is no remote control - clean memory ICs inserted, machine run, shoot and record with her first line in the previous firmware (filmed in IC). Additional information on IMS remote control: PT 2461-103 (see, direct its counterpart SC7461 - 103, a producer different). She has a matrix 8 in 4 (8-gate. Outputs, 4 inputs), 32 combinations only. You can search for untapped. Another chip three teams permits by pressure with a double key on the fifth door (in the matrix it is 20 +22, 20 +21, 20 +23). If the code is required on the current page is, then the search does not take much time, because 20 combinations are used already. And yet, in recent years (that I met) - marking the top body panels are often marking corresponds to the processor (the last four characters, in particular, LC863332A - 5Z51: Remote 5Z51), that indirectly evidenced by the fact that this type of panel will work with this processor.
* * *
| |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: سرفس شامل أجهزة service-mode CHINA الثلاثاء يوليو 19, 2011 8:44 pm | |
| Entertaining INFORMATION: 31 foot LC863320 - BUS OPEN (my schemes - SAFTY) for the closure on mass on the screen (it via 10K "primed" to 5 volts and the service jack goes - from the mass of the second conclusion) any loss of control of TV-like, unused input for protection are different. On the modification of the inscription, which is on the TV screen displays: The inscription is changed easily at any other in the border up to 10 (12 and) characters; Only characters with pictures or Latin - the usual programmer (I work with pony prog) - saver explicitly visible on the side (in 000 170 line) - the ASCII code. Screensaver is written in the main field, at the addresses that the same letters are typed in hex, ASCII only on these shows addresses the literal value. When writing to abide by the word alignment on the screen - the middle of any word must match the address 0176h to the letter I (AKIRA). Direct proven replacement: LC863328A - 5W63 changes to LC863328V - 52E5 (price around $ 10) maintaining control of the native (or 54V3 5Z51, or control is taken from Jinlipy 3728 (30)). LC863324A-52C9 - without any alterations to change LC863324A-5S68. 52C9 one to one change - 5N94, 5N17, 5S68 - all without the Russian language. 5S68 timer is on connection and disconnection, as well as hours, in other similar. Information has not been tested by me personally! He worked with the chassis, on which there are two kinds of seats seat - under 863 328 (332) and 863 532 (the same body, but twice), any one of them is set + Jumpers on the PCB switching (like not trying, because in most processors similar to the replacement took with PP subquality TV tube, etc. TDKSa on Economic reasons PREDTORG non-renewable). To date, no other information on the DIRECT interchangeability.
* * *
| |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: سرفس شامل أجهزة service-mode CHINA الثلاثاء يوليو 19, 2011 8:45 pm | |
| Chassis PAXX0081 LC863548B (36pin), memory 24C16, control chip SC7461-103, LA7910, LA76810A + LA7642N, CD2611, LA78040, TDKS: BSC24-09G. Entering the servic - panel to turn down the volume of zero, holding, DISP press (a rectangle with a plus) on the remote. A little clarification:
- chassis on which it is, the fastest, SKYWORTH developed (china).
For the first time it seemed to just under that brand, although, of course, other options are likely to occur. In SKYWORTH, like, in the second letter of the chassis - is the foundation on which the chip chassis is made In particular: 5S30 - SGS 3Y01 - SANYO 5P30 - PHILIPS 5T51 - TOSHIBA 5I30 - ITT etc. .... Supplement for service on that processor. The above method produces only access to the service menu to the reduced, in which the sub-picture modes are set, geometry and balance. For access to the service menu should be expanded: In the work on the front panel, turn down the volume to zero, hold, put pressure on the remote control AV / TV. Advanced Mode submenu has 14, 00 ... 13, including appearing service in lightweight mode. At the top of any sub-string state displayed with the number of active sub. Bust positions in any sub-buttons CH +, CH-, P +, P-, cross, modify the values buttons VOL + / - cross. To convert from one submenu to the second must be the top status bar to select the active submenu and push button or VOL +, or VOL-. Writing to memory after the departure of the duty room automatically. * * *
عدل سابقا من قبل أشرف عثمان في الثلاثاء يوليو 19, 2011 9:00 pm عدل 1 مرات | |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: سرفس شامل أجهزة service-mode CHINA الثلاثاء يوليو 19, 2011 8:48 pm | |
| Warning: SETUP SELECT set equal to "1", since "0" - only 0 ... 2 sections, and at "1" all sections 00 - 13 are opened. The first press - on the screen FACTORY Second press - on the screen B / W BALANCE Press a third time - on the screen sections of the service menu Paging Menu - Mute (on the remote control - a crossed speaker) ADJUST MENU 0 V. SIZE 34 H. PHASE 13 V. POSITION 48 V. LINE 14 V. SC 10 NT.V.SIZE 00 NT.H.PHASE +03 NT.V.LINE +02 NT.V.SC +02 NT.V.POSI. 06 ADJUST MENU 1 CROSS B / W 0 FORCE 60 HZ 0 Parameter R-Y/B-Y G. BL 8 Parameter B-Y DC LEVEL 8 R-Y/B-Y ANG. 8 Pairs. SECAM B-Y DC 8 R-Y DC LEVEL 8 Parameter SECAM R-Y DC 8 ADJUST MENU 2 VOLUME OUT 105 RF.AGC 23 ZOOM SIZE 96 H.BLK.LEFT 6 WIDE SIZE 48 OSD H. POSI. 19 H.BLK.RIGHT 2 OSD.V.POSI 19 SETUP SELECT 1 SCR.H.POSI 1 If SETUP SELECT to set the value of "1", the remaining sections of the menu will open ADJUST MENU 3 POWER OPTION 1 76810/76818 1 POWER ON KEY 1 POWER LOGO 0 BLUE/BLACK 0 P. V. MUTE OFF 0 BLK. PROCESS 1 SCREEN TIME 1 SCREEN OPT. 3 SCREEN TYPE 0 ADJUST MENU 4 SEARCH SPEED 0 TUNER OPTION 0 BAND OPTION 1 SEARCH CHECK 1 VL / VH FREQ. 0 AV IF STATUS 0 VH/UHF FREQ. 0 MENU BACK 0 MENU ICON 0 PROMPT TYPE 0 ADJUST MENU 5 S-VIDEO OPT 0 AV OPTION 1 ONLY AV MODE 0 SCART OPTION 0 DVD OPTION 0 OFF TRIGGER 60 DVD OFF TIME 3 DVD KEY DEF. 0 ON TRIGGER 180 DVD PORT DEF 0 ADJUST MENU 6 CALENDAR 1 GAME OPTION 1 ZOOM OPTION 0 CHILD LOCK 0 SENSITIVITY 0 LINE MODE 1 REMEMBER AV 1 HOTEL VOLUME 60 HOTEL MODE 0 ON POSITION 255 ADJUST MENU 7 RUSSIAN OSD 1 ENGLISH OSD 1 FRANCE OSD 1 TURKISH OSD 1 SPANICH OSD 1 GERMAN OSD 1 ITALIAN OSD 1 ARAB OSD 1 PERSIAN OSD 1 ADJUST MENU 8 LV 1116 GAIN 0 STEREO OPT. 0 ON. MODE 0 WOOF OPTION 1 WOOFER GAIN 4 SUB. CONT 31 SUB. SHARP 10 SUB. COLOR 15 B.B. 60 BRIGHT SUB. TINT 10 ADJUST MENU 9 N3.58 OPTION 1 PAL OPTION 1 SECAM OPTION 1 N4.43 OPTION 1 COLOR AUTO 1 5,5 M OPTION 1 4,5 M OPTION 1 6,5 M OPTION 1 6,0 M OPTION 1 ADJUST MENU 10 V. SEPUP 1 AFC GAIN 0 VIDEO.LEVEL 6 CD.MODE 0 FM.LEVEL 15 SOUND TRAP 4 HALF TONE 0 H. TONE DEF. 1 OSD.CONT 60 DIGITAL OSD 1 ADJUST MENU 11 VIF.SYS.SW 0 VOL. FILTER 1 MID.STP.DEF 1 BRT.ABL.DEF. 0 RGB TEMP SW. 1 BRT.ABL.TH. 4 YUV OPTION 0 VCO ADJ.SW. 0 FSC. / C-SYNC 1 C.VCO.ADJ. 2 ADJUST MENU 12 G-Y ANGLE 0 VREST TIMING 0 V.BLK.SW. 0 C. KILLER OPE 4 FBPBLK.SW. 1 PRE / OVER ADJ 1 WPL OPE. 1 CORING W / DEF 3 PRE / OVER SW. 0 ADJUST MENU 13 DC.REST 0 Y GAMMA STA. 0 BLK.STR.GAIN 2 A.MONI.SW. 1 BLK.STR.STA. 2 V.LEV.OFFSET 2 S.TRAP.SW. 1 OVER.MOD.SW. 0 OV.MOD.LEVEL 0
* * *
| |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: سرفس شامل أجهزة service-mode CHINA الثلاثاء يوليو 19, 2011 8:49 pm | |
| Log into the service menu TV chassis 3Y11 Log in Service mode: Push down on the "MENU" button so that the message originated PICTURE MENU, then push the button "Q. VIEW" or "RETURN", click "MUTE" to return to CPU. The unit will enter the regime established by the manufacturer. User can use the button "Sleep" to change the menu page of the manufacturer and use the button "User Menu" to exit the manufacturer. Button CH + / - translate the menu items, buttons, VOL + / - adjustment of values. ERC 21SP50 (CE2181), LC863332A-5Z51 - (analog FUNAI S2100PF, S2500PF) - used panel: RSU21SP50. Entering the service menu: using the remote control, push (RECALL (DYSPLAY)), then push (V-) and hold it a few times. The screen will appear the inscription 'FACTORY'. Playing several times this operation will lead to on-screen 'C / B ADJUST', then 'ADJUST', zatem'SETUP 'and come back to' NORMAL TV '. Removing the lock - push button on the CALL and hold almost a minute. Joint information on remote peers: 54B3 = 05D5A = 5Z51 = SYZ = 53W3 = HX55K8 = 50JI (Sharp) = 57L8 (Panasonic) = KLX-55K9T = 52E5 = 56S8 = 54D5 = LW-55L7 = LX-148 55P2 = 5Y29-S1 = 52H8 = XU-5251C-N (Panasonic) = (for remote control MAC MAXI - code 1379)
* * * Another variation chassis M28 GDET0102-02 processor 8891CSBNG6KF8, memory 24C16 Feature is that when installing a clean memory becomes a TV child lock Code to exit 0000 * * *
عدل سابقا من قبل أشرف عثمان في الثلاثاء يوليو 19, 2011 9:01 pm عدل 1 مرات | |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: سرفس شامل أجهزة service-mode CHINA الثلاثاء يوليو 19, 2011 8:51 pm | |
| TV on TMPA8891CSCNG6V12 Entering the service menu using the remote control: push the "MENU", menu to adjust, CH-"push" chanel to choose to press "6483", "2483", "6568" to enter into FACTORY. By FACTORY, "DISP" click to order adjustments in B / W-balance to enter. In the adjustment B / W-balance, push series Channel 1, Channel 2, Channel 3, Channel 4, and so on to 7, DISP, to the mode settings page enter F1 - F7 service. Entering service mode pages F8 - F15 for FACTORY 1 - 7 pages of the menu, push "6483", "2483", "6568" F8 to get to the page at the same time are included in F8 - Page F15, to press MUTE and Return, to adjust menu to press Channel 1, Channel 2, Channel 3, Channel 4, and so further to 9, in order to service mode pages to get F1 - F9 service, to press 0 to get into the mode of adjustment B / W-balance. Push "DISP" BACK. Push the button on the control distance "CH +", "CH-", to select the chanel, pressure "Vol +", "Vol-", meaning that the service change. [ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]* * *
عدل سابقا من قبل أشرف عثمان في الثلاثاء يوليو 19, 2011 9:03 pm عدل 1 مرات | |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: سرفس شامل أجهزة service-mode CHINA الثلاثاء يوليو 19, 2011 8:53 pm | |
| Processor TMPA8897CPNG6PN9 datasheet: A detailed description of all bytes of options, in a bit. Memory Card (Addressing of bytes in the dump) EEPROM. Service mode. In essence - this is a service manual .. Moreover, entry into the S-mode service reported two completely different Chinese methods. 1) reduce the volume to 00 on the panel, holding, pressure [DISPLAY] ([OSD] or [RECALL] or [rectangle with a plus]) on the remote control 2) push [MENU], then quickly dial code 6,4,8,3. On entering the D-mode extended silent, but for this, likely to need - in the S-mode, while, push [DISPLAY] ([OSD] or [RECALL] or on the remote control [rectangle with a plus]) push and hold [VOL-] on the panel, holding> push [DISPLAY] ([OSD] or [RECALL], or by remote control [rectangle with a plus]). By analogy with microprocessors 8851CPNG6EG1, 8891CPBNG6NA3 given type of remote control bytes CUSL = 08, CUSH = F7. * * * TV CHINA, Chassis SS2.
CPU LC863532 - 54H7, 54D5, 50S8, 5Z00, 50S9. Entering the service menu: convert to 0 volume, push the MENU button and quickly dial the code 6568. * * * TV CRYSTAL CR-3014, EEPROM - 24C08, TMPA8891CSCNG6V12, Tuner - MV-3DE (M81002A). Entering the service menu: press VOL-to lokalke and panel DISP / LOCK. Next DISP / LOCK-ohm sub to turn F1, MUTE button then in F2, etc. To display the sub-F8, and more pressing in 2483. * * * TV STV14001, CPU TDA11106PS/V3/3. Ingredients: CPU TDA11106PS/V3/3 sticker NT11106PC303CG, memory 24CO8A, HOT D1651C, ULF TDA2003, frame LA78040A, BP C5287, tuner CWC-5053-V8, TDKS (BSC25-N0439) BSC24-0402. Came after the storm. When trying to connect to the duty office immediately goes away. Perepalo processor. Firmware workers do not work. With firmware clean start, but the buttons on the front panel confused, Russian. language is not, AV2, etc. determine what must be disable EVG = 0 (this option to clean off), but enter into service can not keep up, because once in St.By leaves. In a working firmware by the programmer (by comparison) at 000080-04 and 000060-02 in place (50) (09) staged (10) (08). TV came to life! Entering the service menu mode on the remote desktop press: MENU, then dial the code 6,4,8,3 (code 1379 MAK-FOCUS DISP = MODE on the Mac). The menu: DISP, Mute (switching sections and subsections of the menu) Menu "trap": In the section M2 - SETUP SELECT to set-1 and to press MUTE in sections of M0-M9 fall (and can be digital buttons) exit: the red button POWER (or MENU and type code 6 4 8 3 of FACTORY mode)
* * *
عدل سابقا من قبل أشرف عثمان في الثلاثاء يوليو 19, 2011 9:05 pm عدل 1 مرات | |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: سرفس شامل أجهزة service-mode CHINA الثلاثاء يوليو 19, 2011 8:54 pm | |
| TV CTV29601. The composition of memory 24C16, processor TDA12156H1 \ N3 \ 3 \ AJ9, sound TDA2616 MP strw 6756, personnel LA78141. Entering the service menu MENU on the remote and press 5 times RECALL.Vyhod from the service menu TV \ AV press on the remote.
* * * China TV chassis 29M03. M37160 M61260 and. This chassis, at least in our region, less common received than the chassis 3Y01. It has a fake candid TV Panasonic, SONY, GROL, Samsung, HUAZHOU and others, usually 14 - 15'' (With b / a CRT monitor). The inscription on the chassis - 29M03 MAIN-3PCB. Central processor - M37160M8-064FP (planarka 2-sided - 42 feet) + 24LC16 (08) + is a socket to turn the PC on the I2C bus. The video processor - M61260A (planarka 4-sided - 64 feet, apply M61264 M61266 may or quartz + ZQ 4,433 MHz. TDKS - (BSC 24-01N4006E) BSC 25-05N2105A. Near it is made with five branches pins (for picking up - Especially from Wasps, depending). HOT - TT 2170 (VD + R = 47 51Om inside). HR-LA78040 (there is a different type of personnel landing place). Switch Video Inputs - HCF4053BE. ULF sound - TDA2003 (there is a different type of landing ULF). Remote RC09-M301 (as with a drop occurs, and with the LT1388 IC). Graphics TFT TV BON similar, etc. On the screen with no signal from the antenna - iridescent colors and all the floating label SONY, when Sharp brought, then, of course, floated across the screen Sharp. Remote W7-M031B Extra Information - TV WITHOUT EEPROM normally runs. Entering the service menu and service options are presented below. Method 1 - In the menu select "Antenna" in it - a place of "Fine Tuning" (Then press VOL +), and then click the program switching from "0" through "9" - 10 menu items get. Method 2 - Remote control with chip LT1388 - entry into service - a hidden button (Bridged (6 +11) pin) and the button "speaker." Remembering when you exit automatically via the button "menu". In the remote has buttons hidden, with the help of What color balance is regulated, as well as edit the inscription may be that when you turn on TV shows. 3 way - to dial the remote control: Press "MENU" and code 6483 (direct keys access to programs) - there "FAC". Do the second time the same - balance. The third time, will be geometry, and MUTE - the movement of the options. Exit from service - dial again "MENU" and put code 6483. If no SECAM, it is necessary to change the device type in the service, he's changed 4 point, it seems, can not remember exactly, and certainly should be off and on TV, otherwise the settings will not take effect, then, that was normal SECAM, necessary in the second seems to point to install shades SECAM to 23 and everything! Yet there is often the case: the sound is not regulated, and it is constantly at maximum, this is because of the firmware too - EEPROM to flash. If the screen is continuously lit «factory» or «fac» red, but all other functions are carried out - EEPROM to flash.
* * *
عدل سابقا من قبل أشرف عثمان في الثلاثاء يوليو 19, 2011 9:06 pm عدل 1 مرات | |
| | | أشرف عثمان المدير العام
الأعلام : عدد المساهمات : 2402 تاريخ التسجيل : 16/06/2010 العمر : 63
| موضوع: رد: سرفس شامل أجهزة service-mode CHINA الثلاثاء يوليو 19, 2011 8:55 pm | |
| TV noneym processor M37160MAH-090FP, M61260, memory 24C08, tuner EWT-5F3T1-E06W Entering the service menu: MUTE, then SLEEP then PP On the blank memory starts, but adjustment is not memorized, and the service as well. * * * TV + DVD NOKASONIK NK-CTV111DVD on the processor M37150MA-081FP. EEPROM - 24S08, video processor - M61260. Entering the service menu: 21 and 24 feet jumper chip SC6122-001 in the native remote control. On the blank memory starts. Options in the service - picky.
* * *
| |
| | | | سرفس شامل أجهزة service-mode CHINA | |
|
مواضيع مماثلة | |
|
| صلاحيات هذا المنتدى: | لاتستطيع الرد على المواضيع في هذا المنتدى
| |
| |
| |
|