ERISSON 21F1 (UBM)
press simultaneously VOLME - + on the face and wait for 3 seconds.ERISSON 21SP50
To enter the service in MK11 own remote control button solder between 2 and 16 feet m / c, PT 2461-103.
Push the button the 1st time - on the screen: FACTORY; pressure. 2nd time - on the screen B / W ADJUST (reg.
CRT mode); third time - ADJUST (geometry) for the 4th time - SETUP (setup options) 5th Pressing
- out of service. Buttons P and P +; V-; V + help to establish the appropriate values in the right places.
* * *ERISSON 25F2
press simultaneously VOLME - + on the face and wait for 3 seconds
* * *ERISSON 2102, 2103, 21F4, 1401
Entering the service menu: MENU-press 3 TIMES, "P-" press 1 again, then dial the code 2483.
* * *Erisson 2120.
Replacing the microprocessor to LC863320A-5N94 LC863320A-5R76.
Must take into account that such a change has to change the remote control. Remote Processor
SC7461-103 (from Erisson 14GX37A apply). Pull transistors Q001-Q003. Change
Resistors R004, R002, R006 22 ohms. Put decoder (I use K155ID1)
inputs 1 and 2 to the conclusions of 41, 42, IC001 (inputs 4 and 8 to ground) output 1, 2, 3 holes
collectors of transistors Q002, Q003, Q001. Breaking the path between the base of Q610 and
R630, and the transistor npn nest at R630 base, emitter to ground, collector
to the base of Q610 and the resistor 5 through 22 ohms. Refine cost controls for
matching buttons: Vypayat resistors R06 and R08, and instead put the jumper.
Rather than put R09 3 k (series R08, R09). Between the buttons SW3, SW5
install 3.9 ohms (R06). Between the buttons and SW4 SW1 - solder resistance 15 kOhm
(R03). Instead, solder resistance R04 13.8 ohms (R05 + R04).
* * * TV ERISSON 1430. ETA-1 chassis.
Percent 8891CSBNG6KF8, memory 24S16, HOT D5023, staff LA78040N,
BP STRG5653, TDKS BSC59T 2 (B), TUNER TAF5-C4I23, SOUND TFA9842AJ, REMOTE 21SF30.
Entering the service menu: volume set at "0"
to press "MUTE" on the remote and holding it, press on TV "MENU".
Exit off at the duty room.
For information - The following panels are suitable: K16R-C2 (C3, C10, C17); K10R-C3R (C17); K18F-C4
* * * TV ERISSON 29SF10.
Processor - LA76938N SUSOC 7N 58R2 JA06,
TUNER - EWT-5F3T1-E06W, MEMORY - 24C08, QUARTZ - 4.433619 MHz, UPS - QQ1265RT,
ULF - LA42352, HOT - C5148, trans PSU - BCK-40-LF01X-3, 32.768 MHz,
STAFF CHIPS - LA78141, FBT - BSC29-M2477 5131-051409-31
Entering the service menu: IN front of the TV VOLUME MINUS set to "0". Then dial the MENU, and code 6568 ...
* * * TV ERISSON model 21F5
chassis 3Y18, LA76936Y 7N 58M2;
HR LA78040B; 24C08WP; BSC23-N0164; VLF LA42351; FBT Tuner EWT-5F3M43-EW;
Entering the service menu with remote staff: quickly press the Menu - QView - Mute,
inakonets VOL - any.
* * * TV ERISSON 21UF24, 3P66 chassis.
Processor TDA11136PS/N3/3/AH8 CR7967 CR7457 TOP-E-090 115-EW TSG610022B1B
1 NXP B.V. 2006 Kadr.LA78141, Tuner EWT-5F3T1-E06W, HOT. 2SD5023,
BP. STRW6554A, sound chip TEA2025B, FBT. BSC25-N1574.
Came with the diagnosis - the line voltage too high. STRW6554A defective
(Scattered) on STRW6556A replaced, infa-(STRW6754 = STRW6753 =
(STRW6750F) = STRW6756 = (STRW6765) STRW6554A = STRW6553A = STRW6556A - output differ).
B + operating mode / ST.BY = 115v / 55v
Entering the service menu - using the desktop on the remote to press: MENU, then Q. VIEW, then PP
Menu Buttons accelerating voltage adjustment «SLEEP» (TIMER)
Menu Buttons adjust the geometry of the "0" Remote
Menu Buttons adjust distortion "1" Remote Control
Menu Buttons adjust the balance of PAL "2" Remote Control
Exit from the menu service button "+ squared" (DISP)
Turn on / off mode run Buttons "PP" in the mode of service.
Menu "trap": a section of zero (Menu adjusting the geometry of "0") to enter
option in SC - on the remote control to dial: 89 - fall into the other
sections of the "00" - "14" - buttons on the remote digital
For removing "the protection of children" button on the remote control "LOCK". Can
by the programmer at: 0000B0 - 0F Zamesto (05), set - 04 (determined by comparison).
* * * TV ERISSON TV2150 c 4S02 chassis.
Entering the service menu.
Press the button sequence "SKIP", "VOL-", "AFT"
button "-PROG +" - controlled the choice of parameter
button "-VOL +" - Adjusting the selected
Exit from the menu - Vol. "PIC
* * *