أشرف عثمان للإلكترونيات
أهلا وسهلا بكم ونتمنى أن تستفيد معنا



 
الرئيسيةالتسجيلدخول
شاطر | 
 

 سرفس مود SAMSUNG

استعرض الموضوع السابق استعرض الموضوع التالي اذهب الى الأسفل 
كاتب الموضوعرسالة
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات: 2241
تاريخ التسجيل: 16/06/2010
العمر: 54

مُساهمةموضوع: سرفس مود SAMSUNG   الجمعة مايو 06, 2011 7:26 pm

Chassis KS1A
login - (STAND-BY) (DISPLAY) (MENU) (MUTE) (POWER ON)
output - POWER OFF

Chassis KS2A
entrance - (STAND-BY) (DISPLAY) (MENU) (MUTE) (POWER ON)
(STAND-BY) (INFO) (MENU) (MUTE) (POWER ON)
output - POWER OFF

Chassis KS3A
Login in service: PIC.OFF--> DISPLAY ---> MENU ---> MUTE ---> PIC. ON

Chassis: KS9A
Login in service: STAND_BY - DISPLAY - MENU - MUTE - POWER ON
Output: - POWER OFF

Chassis KS9A (P)
login - On a remote push button in the following sequence:
STAND-BY (POWER OFF) - DISPLAY-MENU-MUTE-POWER ON
output - POWER OFF

Chassis KSBA Proc. TDA12176PS
login - (STAND-BY) (INFO) (MENU) (MUTE) (POWER ON)

chassis P1B
login (STAND BY) (P. STD) (HELP -?) (SLEEP) (POWER)
output - (STATUS)

chassis S15A
login
1.TV included in the operating mode.
2. on the remote press the (sleep) with the emblem of hours.
3. press the button on the hidden button (factory).
Memory Entry - (Sleep)
output - 2 times (Factory)

chassis S16. prots.TDA 12025PQ/N1F80
login - Turn on network TV button. After switching on the TV goes from standby to operating mode, and the LED blinks 3 times.
Then
on the RC series to press POWER OFF (translated to DR) - INFO - MENU -
MUTE - POWER ON (translated by RR). When entering a combination is
limited to about 5 seconds.

chassis S56A
login - PICTURE OFF, DISPLAY, MENU, MUTE, PICTURE ON

chassis S65A
login - INFO, FAKTORY, FAKTORY
output - MENU

Chassis SCT11B, SCT12B, SCT-13
login - (STAND BY) (P. STD) (HELP-?) (SLEEP) (POWER)
output - (HIDDEN)

Chassis SCT-51A SCT-52A
login - (PICTURE OFF) (SLEEP) (P. STD) (MUTE) (PICTUPE ON)
output - (STATUS)

Chassis SCT57B CK-22B5SXR CK-565BSXR Proc. SAA5291PS-135
1. TV is included in the working rezhim.2. on the remote press (DISPLAY).
3. press the remote control button hidden (factory). 2 times (Factory)

Chassis SCV11A
login - (STAND BY) (P. STD) (MENU) (SLEEP) (POWER ON)
output - POWER OFF

chassis Z68 percent. SIM131
login - (AV) (SLEEP TIMER) (POWER)
output - POWER OFF

Chassis L63A
Login: - POWER OFF - INFO - MENU - MUTE - POWER ON
Output: - POWER OFF


عدل سابقا من قبل أشرف عثمان في الخميس يوليو 21, 2011 11:25 pm عدل 1 مرات
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات: 2241
تاريخ التسجيل: 16/06/2010
العمر: 54

مُساهمةموضوع: رد: سرفس مود SAMSUNG   الجمعة مايو 06, 2011 7:27 pm

Samsung CB-20F 122
Processor TDA9381PS/N2/3/0462
Log in to the service: (Display) - (Menu) - (Mute) - (Power)
Yield: (Power)


Option Table
1. System: CF - color incl. SECAM / PAL
7. 2ND SIF: ON - Sound incl. B / G 5.5

Convert sound curves. to 32n percent.


الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات: 2241
تاريخ التسجيل: 16/06/2010
العمر: 54

مُساهمةموضوع: رد: سرفس مود SAMSUNG   الخميس يوليو 21, 2011 11:11 pm

SAMSUNG
Rubin (Rubin) 51M06
Service mode range S06
While holding the book. AV power on the TV and hold for five seconds, or close
at 250-500 ms contacts 6 and 7 of the service connector. Selecting options book. P + or P-, change
values ​​of VOL + or VOL-. Making a memory book. TV.
Installation / removal of the regime "hotel"
1.Voyti in the Options menu (Book menu or the blue book. PDU)
2.Install with remote transparent background menu (see Operating Instructions)
3.Ustanovit cursor on program number
4.Nazhat and hold the remote control book. Inclusion of the hidden teletext reception before the appearance of
right corner of the label HOTEL ON / OFF
Removing the protection of children
enter in the menu-button menu or the blue button on the remote control, set to control blue
transparent background - see manual and place the cursor on the line lock, press and hold
on the control button on the hidden until receiving TXT inscriptions LOCK OFF. (Line CASTLE
may be absent from the Options menu, if enabled HOTEL.)
Rubin (Rubin) 51M10
To enter the service to a standby mode press the menu button on the front of the TV
and the 0 button on the remote. In order to remember the settings, press the TV button and holding it off the TV from a network
Removal of the Castle: Enter the Options menu, select Lock, dial (2) (2) (white button)
Rubin (Rubin) Seria S07
Processor SAA5531PS/M4/0599
Turn on your TV by pressing the (volume +) and (menu) on the front of the TV.
Navigating the menu buttons (P +) and (F), changing the buttons (volume +) and (volume -).
SAMSUNG
4-2-1 Procedure for "options" Mode
1. This mode uses a standard remote control.
The service mode is activated by: (1) pressing "FACTORY" Service key on the panel,
or (2), enter the following remote control sequence (2 seconds):
STAND-BY> Display> MENU MUTE>?> POWER ON
2. "SERVICE (plant)" message will be displayed. Service mode has three components:
Adjustment, and Reset option.
3. Access Control mode by pressing the "Volume" button (up or down). Adjustment
parameters are given in the accompanying table and select by pressing the CHANNEL
Keys (_,_).
4. The choice of sequence for PAL / SECAM B / G, L / systems:
up or down key: AGC> TXP> AFW> SBT> SCT> SCR> STT>
RG> GG> BG> TCT> SC> SL> PVS> PHS> NVS>
NHS> CDL BCS>
5. Volume keys increase or decrease the correction values
(Stored in nonvolatile memory) when setting mode is canceled.
4-2-3 AGING mode (room Only)
This model is used to preheat the manufacture of the CRT - it's access to
Plant two times by pressing the "FACTORY" key.
Even if the TV blackout, the aging treatment had not been canceled. "Aging"
marking on the screen. AGINGmode abolished by suppressing the "FACTORY" key.
4.4 Other adjustments
Basic 4-4-1
1. Typically, a color TV needs only slight touch-up adjustment upon installation.
Check the main characteristics such as height, horizontal and vertical sync and focus.
2. The photo should have good black and white details. There should not be
undesirable shades of color, if color shading is to fulfill the purity and convergence
adjustments described below.
3. Use the provided test equipment or its equivalent.
4. The correct impedance is important.
5. Avoid overloading. Excessive signal sweep
The generator may overload the front end of the TV. When installing the signal markers, do not
allow the marker generator to distort test results.
6. Connect the TV only to an AC power source voltage and frequency
as indicated on the backcover nameplate.
7. Do not attempt to connect or disconnect any wires, but TV is on.
Make sure the power cord is disconnected before replacing any parts.
8. To protect against electric shock, using the isolation transformer.
4-4-2 Automatic Degaussing
Degaussing coil is installed near the tube, so that external degaussing after
moving the TV should be unnecessary. But the receiver must be properly installed on degaussed.
Degaussing coil operates for 1 second after power is turned on.
If the collection has been moved or turned in another direction, disconnect its power supply, at least 10 minutes.
If the cabinet or the cabinet became magnetized, poor color purity will result. If
this happens, use of external degaussing coil.
Slowly move the degaussing coil tube faceplate pattern and the sides and
the front panel. Slowly lift the coil at a distance of about 6 feet before removing
power.
4-4-3 High Voltage Test
NOTE: There is no high voltage adjustment on this chassis. B + power supply
Power should be set at 125 volts (full color bar input and normal pattern).
1. Connect a digital voltmeter to the second anode tube.
2. Turn on the TV. Set brightness and contrast to minimum (zero beam current).
3. The high voltage must not exceed 27.5KV.
4. Adjust the brightness and contrast in both extremes. Make sure that the high voltage
does not exceed 27.5KV in all conditions.
4-4-4 focusing
1. Input a black and white signal.
2. Adjust the controls for a clear picture.
3. Adjust the focus control, with clearly defined lines of the center of the screen.
4-4-5 Screen Adjustment
1. Refer to the ACTIVE channel.
2. Adjust the VR display for normal pictures (not flowering or reverse line).
3. Adjust the focus control, with clearly defined lines of the center of the screen.
4-4-6 Setting the purity
1. Warm up for at least 20 minutes.
2. Connect the CRT deflection yoke and tighten the clamp screw.
3. Plug the convergence yoke into the CRT and install as shown in Fig. 4-1.
4. Input a black and white signal.
5. Completely demagnetize obtained by applying an external degaussing coil.
6. Turn the contrast and brightness to maximum.
7. Loosen the clamp screw holding the yoke. Slide the yoke backward or forward, to ensure
vertical green belt. (Figure 4-2).
8. Tighten the convergence yoke.
9. Slowly move forward and adjust the deflection to the best overall green screen.
10. Temporarily tighten the yoke.
11. Production of blue and red rasters by adjusting low-light control.
Check for a good clean in every area.
12. Tighten the yoke.
4-4-7 White Balance
4-4-7 () HIGH-LIGHT ADJUSTMENT
1. Input a lion's head, or "white" image.
2. Warm up the TV for 30 minutes.
3. Check the data in the service
4. Adjust RG, BG in Factory Mode.
4-4-7 (B) low light ADJUSTMENT
1. Automatically done during the high light adjustment.
2. 4-4-8 Center Convergence Adjustment
1. Warm up for at least 20 minutes.
2. Insert the two tabs 4 pole magnets change the angle between them. Impose
red and blue vertical lines in the center of the screen.
3. Adjust the brightness and contrast to clearly define the picture.
4. Insert the two tabs four pairs of magnets, and change the angle between them. Apply to
red and blue vertical lines in the center of the screen ..
5. Turn both tabs at the same time, maintaining a constant angle, and put red and
blue horizontal lines in the center of the screen.
6. Insert the two tabs a pair of 6-magnets to put red and blue lines on the green.
(Changing the angle affects the vertical lines and rotating both magnets affects
horizontal line.)
7. Repeat the adjustment of 2 ~ 6, if necessary
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات: 2241
تاريخ التسجيل: 16/06/2010
العمر: 54

مُساهمةموضوع: رد: سرفس مود SAMSUNG   الخميس يوليو 21, 2011 11:12 pm

Models SC 6271 WP.
To enter the service menu press the button or HIDDEN
press very quickly following sequence of keys on your remote control: STANDBY, P. STD,
HELP, SLEEP, POWER ON.
Service mode TV "Samsung CK6271, SK7271."
Before entering the service mode, switch the TV using the remote
Remote Control (RC) in standby mode

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

(Stand-by).
The service mode is activated in two ways:
•? On the remote control button is pressed in the following order: Video Prefer • A / V • Sleep
Timer • Power; press the Hidden Service, hidden on the remote. Then in the left
top right corner of the TV screen will display FACTORY.
Service mode has three sub-modes:
•? Major adjustments (Main adjust mode);
•? Delay adjustment of the luminance signal (Luminance delay control mode);
•? White balance adjustment (White balance control mode).
FACTORY mode is canceled by pressing the button, Hidden Service, or by pressing
power off.
Adjustment in service mode


To enter the service mode to adjust the basic parameters submode press
click Status.

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
After that appears on the TV menu (Figure 1), which shows the basic
adjusting the parameters and their numerical value by default (factory
setting).
Explanation of parameters and their range of adjustment shown in the table.
2
Adjusting parameter and select buttons = ¢ (Up and Down) and change its value
buttons
(Lett and Right). Each selected option will flash for one
second.Changing the value automatically saved when you exit this mode.
Selection of basic parameters are in the ring: ... • HS • EW • EP • EC • ET • SL • VA •
SC • VS • PW • ...
Pressing Stereo, Dual Mono and color of the table on the remote control changes from green to
blue and regulated by the parameters of the SS and LA.
To go from the service mode to adjust the delay of the luminance signal click
Video Prefer button initially selected delay setting brightness for PAL
(Fig. 2). Pressing the Video Prefer selected the following parameters:
PAL • SECAM • NTSC 4,43 • NTSC 3.58 • ESCAPE.
Appearance on-screen menu of other options similar to Fig. 2. but in the second row
changing type of parameter and its value.
Selected parameter changes the buttons (Left / Right). The range of variation
parameters is 190-1135 in steps of 45. Changing the value automatically
remembered when you exit this mode.
To
enter the service mode in the sub-mode white balancepress a button on
the remote control Audio Prefer. Originally selected option Red
Gain (gain of red - see Fig. 3). Pressing the chosen
Other options: Red Gain • Green Gain • Blue Gain • ESCAPE
Appearance on-screen menu of other options similar to Fig. 3, changing only the type of
parameter and its value.
Selected parameter changes the buttons (Left and Right). Range
change the settings - 0 ... 63. Changing the value automatically saved when you exit this mode.
PCK53R15
Successively press: STAND BY, P. STD, HELP -?, SLEEP, POWER.
* * *
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات: 2241
تاريخ التسجيل: 16/06/2010
العمر: 54

مُساهمةموضوع: رد: سرفس مود SAMSUNG   الخميس يوليو 21, 2011 11:13 pm

TV Samsung CS-KS1A
chassis
CPU TDA9381PS/N1/3S0293 SPM-802ERN4, Russian, PAL / SEKAM BG / DK. Teletext, geometer .- no.
Entering the service menu: P.off -, then display -, then the menu -, then mute - at the end of P.on.
* * *
SAMSUNG KS4A
4. Alignment and adjustment
4.1 Adjustments
Typically, a color TV needs only slight touch-up restructuring after
installation. Check the main characteristics, such as the vertical dimension,
horizontal dimension, and attention. Note picture and check for good
black and white details. There should be no unwanted shadows color if color
shading now to demagnetize the receiver. If the color of shadows is not eliminated,
re-do the purity and convergence adjustments.
Note:
1. This '4. Alignment and adjustment "refers to applications KS4A chassis.
2. AC power adapter: 100 ~ 230
3. This service manual has been written on the basis of domestic remote
governance model of decision KS4A chassis. Depending on your point of sale and specifications
some specifications may be changed.
KS4A scheme contains the dynamic focus. When the CRT PCB, FBT or CRT replaced
Make sure that the settings are as follows:
4-1-1 General Instruction Alignment
4-1-2 Setting the focus
Dynamic focus control
1. Input crosshatch pattern.
2. Select "Standard" from the menu
3. Include static Focus VR clockwise to set it to its maximum.
4. Turn on the dynamic center of VR counterclockwise, set it to maximum.
5. Include static Focus VR counterclockwise slowly clear
center vertical line.
6. Turn on the dynamic center of VR clockwise slowly clear the third line.
7. Check at the center of the screen. If necessary, make adjustments again 3 ~ 6.
4-1-3 Screen voltage regulation
1. The use of DC a few meters to determine the RC, SC, BK. And then adjust the screen
FBT VR so that the high voltage is Vp-p 175.
4-1-4 White Balance
1. Select "Standard" from the menu.
2. Input 100% white pattern.
3. In standby mode, press the remote control keys in the following sequence:
Display menu, mute, power the TV.
4. Warm up the TV for at least 30 minutes.
5. Staircase signal.
6. Use the Volume + / - buttons on the remote control to select R Drive, G Drive, B Drive, under Cont.
7. Adjust the low-light conditions when viewing the dark side of the screen.
8. Use the Volume + / - buttons on the remote control to select Rcutoff, Gcutoff, Bcutoff, Sat BRT.
9. Setting a high light while watching the bright side of the screen.
10. If this is not correct, adjust the white balance.
11. Press the memory button to exit.
4-1-5 to the south of the brightness
1. In standby mode, press the remote control keys in the following sequence:
Display Menu Mute Power on the TV.
2. Use the channel up / down buttons to get a bright signal to the south of the restructuring.
3. Use the Volume + / -, to select the SBT.
4. Press Menu and Mute on the remote control to adjust the way
to the seventh step in the right screen is not visible.
5. Press the memory button to exit.
SAMSUNG KS7A

2. Alignment and adjustment
2.1 General instructions Alignment
1. Typically, color TV-VCR needs only a small touch-up adjustment upon installation. Test
basic characteristics such as height, horizontal and vertical sync and focus.
2. Note a good picture in black and white details. There must be an undesirable color
shading, if the color of shadows is, degauss, purity and convergence do
adjustments described below.
3. Use the provided test equipment or its equivalent.
4. The correct impedance is important.
5. Avoid overloading. Excessive signal from sweep generator might overload the front-end
TV. When installing the signal markers, do not allow the marker generator to distort test
results.
6. Connect the TV only to an AC power source voltage and frequency, as shown in
backcover nameplate.
7. Do not attempt to connect or disconnect any wires, but TV is on.
Make sure the power cord is disconnected before replacing any parts.
8. To protect against electric shock, using the isolation transformer.
2.2 Automatic degaussing Degaussing coils installed near the tube,
so that external degaussing after moving the TV should be unnecessary. But
receiver must be properly installed on degaussed.
Degaussing coil operates for 1 second after power is turned on. If the set
moved or turned in another direction, the power should be turned off for at least 10
minutes.
If the cabinet or the cabinet became magnetized, poor color purity will result. If
this happens, use of external degaussing coil.
Slowly move the degaussing coil tube faceplate pattern and the sides and
the front panel. Slowly lift the coil at a distance of about 6 feet before turning
food.
If the color of shadows is not eliminated, follow the color purity and convergence adjustments.
2.3 High Voltage Test
NOTE: There is no high voltage adjustment on this chassis. Power supply B +
should be 135 volts (with a full color bar input and normal picture level).
1. Connect a digital voltmeter to the second anode tube.
2. Turn on the TV. Set brightness and contrast to minimum (zero beam current).
3. Adjust the brightness and contrast in both extremes. Make sure that the high voltage
does not exceed 30 kV under any circumstances.
6.2 White Balance
1. Warm-up TV, at least 30 minutes.
2. Enter Service Mode by pressing the remote control buttons as follows:
Turning off the Information Menu _ _ _ Mute Power
3. Initialization of all data.
4. Enter the model of Toshiba.
5. Using a probe (CA100), make of White Balance.
(1) Adjust the low light conditions.

  • Brightness adjustment for a lot of Y.
  • B Cutoff to adjust to the set Y.
  • Adjust the Cutoff R on X.
(2) Adjust the High Light.

  • Adjust the contrast to the sub-set of Y.
  • B Adjust the trip to the set Y.
  • Adjust R trip to the set X.
(3) Check the value of low-light conditions. If necessary, adjust low light.
(4) Check the High Light. If necessary, adjust the high light.

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات: 2241
تاريخ التسجيل: 16/06/2010
العمر: 54

مُساهمةموضوع: رد: سرفس مود SAMSUNG   الخميس يوليو 21, 2011 11:18 pm

CHASSIS KS1A
Block wells - TAEL-G253D I2C-AT24C08A, potsessor - TDA9381 PS/N1/3S0283 (SPM-802ERN3)
Entering the service mode: STBY-DISPLAY-MENU-MUTE-PWRON
The screen shows:
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Moves keys + - volume and channel switching.
ADJUST

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

OPTION

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

Exit from the menu: POWER OFF
operation and service mode for setting up TV chassis KS1A SAMSUNG 2039
Over time, some parameters are changing apparatus.
It is defined vetshaniem parts, damage the emission properties
tube, external factors, in particular, the influence of electromagnetic
fields. Because there is often a need for these or othermachine settings, even if it is in order. Similar
settings include: the restoration of white balance, alignment
horizontally and vertically, setting limits adjustment
brightness, adjusting the geometric dimensions of the raster adjustment
focus of the image, adjusting color purity, exhibiting
AGC threshold, etc. Before you make adjustments should demagnetize the picture tube.
Any of these settings has its own peculiarities. We analyze
process of their implementation from start to finish for vehicles SAMSUNG 2039.
Should take into account that outlines the appropriate settings and to other
models of SAMSUNG, implemented in line KS1A, 20 - 14 - and 21-inch CRT.
The course setup, we will go from the entrance to the service mode (Service Mode),
a temporary name (Factory Mode) Mode factory settings.
Its entrance is inevitable and even the substitution of an integrated circuit memory device and IC902 CRT.
Log into the service menu is done with (remote) remote
management.
To do this, perform the appropriate operation (by pressing the
corresponding buttons and menu selection):1. DISPLAY> FACTORY.I then
go:
Option for the standard remote control 2. STAND-BY> DISPLAY> MENU>> MUTE> POWER ON
In this case the raster notice there "SERVICE (FACTORY)". The service menu is in:
OPTION (Options), ADJUST (Settings), RESET (Reset).
Exit the setup mode by pressing the buttons to ensure
VOLUME volume selection meet for the menu item.
And the list is reproduced on the screen settings, the choice of any
performed by using the switching programs. After selecting
the desired setting you can change to a smaller or larger side
buttons adjust the volume. To exit the service menu again to push the button "FACTORY" or "POWER OFF".
The election is decided in such settings, the following sequence:
SCT> SBT> GG> BLR> BLB> RG> LCO> VS> NDL>
BG> VSL> VA> SC> HS> SDL> STT> SSP> PDL>
PSR> NSR> AGC
> VOL> TXP. The purpose of the settings, the ranges of their transformation and
ratings by default (factory setting) is shown in the table.
The column "OSD" - the name of the settings that are rendered on-screen menu.(On Screen Display).
In the service menu with table electing optional customization
it is possible to change the values ​​of individual parameters (in brackets shows the ratings provided by options):
o selection of reception - SYSTEM;
o incorporation of LNA-LNA (ON);
o the election of the outgoing interface device - JACK (RCA);
o mode of operation of sound section - AUDIO (MONO),
o the election of the automatic power-off - AUTO
POWER (ON);
o selection of display method on screen - ZOOM (NOR / ZOOM / 16:9 -
estestvennyy/povyshennyy/16: 9);
o the inclusion of "Hotel mode"-HOTEL MODE (OFF).
o filtering the signal of the 2nd IF (sound) - 2nd SIF (ON);
BKS option must be enabled (ON)), and SBL option is disabled (OFF.
Reset mode (RESET) automatically resolves all make a difference
default settings. And cometh in the automatic modes
off state (OFF), and all settings are erased block SLE.
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

Let
us analyze the sequence of adjustment of individual parameters.1. Level
control of high voltage. First, should monitor the supply voltage, "B
+"
which shall be 125 V. Then is connected to a second digital kilovoltmeter anode tube
include apparatus and exhibited levels of contrast and brightness at the very least (reach zero
current rays). Moreover, the high voltage required to show the 27.5 kV. Following this increase the brightness
and contrast to maximum. The level of high voltage can not change.
2.Regulirovka focus pictures. Serve with a test signal generator black and white signal
and the focus knob in the center of the screen reaches a clear display of lines.
3. The voltage on the cathode tube. Need by the end of GK panel tube connected schyn
oscilloscope. After that serves a generator test signals with signal levels of gray.
Pressing the button "R" Remote control exhibited a typical size image. Variables p screen VR on TDKS
(Fig. 1) regulate the signal range 120 ± 2,5 V.
4.Podstroyka color purity. Before performing the operation apparatus is heated during 20 min.
Released until the bolt attaching the magnets (Fig. 2). The signal is fed to a white field generator output
test signals. Through an external coil completely demagnetize the picture tube.
Adjust the brightness and contrast of being kicked out to the max. By moving the magnet back and forth along
filler tube, reach the screen of vertical green stripes (Fig. 3).
Carefully shift the block information. Slowly moving forward block magnets reach a uniform color
vertical green stripes and the time fixed block magnets. Alternately, connect only the red
and only the blue gun control purity of the color blue and red fields, respectively. Irrevocably fixed block magnets.
5.Regulirovka information. Chased the unit in the course of 20 minutes. Give a signal net of the field.
Turn the four-pole ring magnets reach the attention of the red and blue vertical lines
in the middle of the screen (Fig. 4). Adjusting the contrast and brightness achieve optimum clarity
Pictures.
By modifying the angle between the four-pole magnets reach the optimal
information Redsand blue vertical lines in the middle of the screen.
Simultaneously turning the two rings of magnets, and saving
a certain angle between them, connect the red and blue horizontal lines in the middle of the screen.
In a similar manner twist hexapole magnets, reaching combination of blue and red lines with green.
Should be remembered that the transformation of the angle between the magnets allows to reduce vertical lines, and
synchronized their appeal - the horizontal. If you need adjustments reproduce.
6.Vystavlenie AGC threshold. For what value are set at 23B AGC service mode.
7. Putting the signals pre-adjustment of color saturation. When performing this procedure
useful values ​​of PSR and NSR to determine by 2 and 5.
8. Adjust the geometric dimensions of the raster. Performed in the order: SC> VS> HS. Transmit to the machine
signal of the test pattern. Expose the signal (SOSCorrection) S-correction
about
9 to 20 - and 21-inch and 0 to 14-inch CRT, and the nominal signal VA,
approximately40. Modifying (slope vertical) setting VSL, expose the
value of the raster so that the lower
range were seen four divisions (Fig. 5). After that adjust (vertical shift) parameter VS
so that the higher range were seen four divisions (Fig. 6). Finally, adjusting (the size of
horizontal) parameter HS, expose the left and right boundaries of a picture (Fig. 7).
CHASSIS KS2A

Log in to the service: (STAND-BY) (DISPLAU) (MENU) (MUTE) (POWER ON)
CHASSIS R1V.
Log in Service: Alternately push button bychtro: STAND BY, then P. STD, HELP -?, SLEEP, POWER.
In order to get out of the service: STATUS.
CHASSIS S15A.
To enter the adjustment mode should be: • to enable the device to normal operation;
• the remote control push button with a picture of Sleep hours; • push button on the remote hidden (factory). On
screen will appear line: ADJUST, then, then OPTION RESET. Adjusting the buttons being implemented V-,
V +, P, P +, and the memory button vkyuchenie Sleep. Values ​​VCD - 80, AGC - 9, PVA - 42, SBT - 8, SCT -10,
TSC -13, PVS - 32, SCR-10, SC-12, BG - 34, RG -47, GG -32, CDL - 4, LU - 0, PSL - 32, PHS - 40, OPTION
better not touch. Exit the service menu: twice Factory
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات: 2241
تاريخ التسجيل: 16/06/2010
العمر: 54

مُساهمةموضوع: رد: سرفس مود SAMSUNG   الخميس يوليو 21, 2011 11:19 pm

CHASSIS SCT11A, B:
Push a button with the remote procedure: STAND-BY -> P. STD -> HELP -> SLEEP -> POWER ON. Exit
service mode STATUS. Under the control sockets hidden hidden button HIDDEN, through the button
You can go out and enter the menu.
SAMSUNG S16A
Entry into service mode for TV chassis S16.
Turn the power button. After connecting the device to jump out of duty (DS) in the working
mode (PP), and the LED blinks three times.
After this, in turn put pressure on the remote control button POWER OFF (translation in the duty room) - INFO -
MENU - MUTE - POWER ON (transfer to RD). Length of combinations is limited
approximately 5 seconds.
SCT11A, B Model TVP5050, TVP3350, TVP5350
Log In - Stand-By - P. Std - Menu - Sleep - Power On.
After
entering the service mode appears on the screen menus: Reset
Adjustment, Option byte,.Abbreviations used in the mode of Adjustment:
Horizontal Shift-size horizontally, SBT - Sub Bright,
AGC - autom. adj. amplification, SCT - Sub Contrast, then STT - Sub Tint, then RG - Red-Green drive gain,
Further PSL - PAL vertical SLope, then SCR - Sub Color, further NSL - NTSC vertical SLope, then PDL -
Pal Delay, then BG - Blue-Green drive gain, further NDL - NTSC Delay, then Cutoff, then RC - Red
Cutoff, then GC - Green, then BC - Blue Cutoff, Shift, etc. PVA - PAL Vertical Amplitude PVS -
PAL Vertical, then PHS - PAL Horizontal Shift, then NVS - NTSC Vertical Shift, then NVA - NTSC Vertical Amplitude.
To enter the service of the duty room to on the remote control in turn put pressure
these keys: P. STD - HELP - SLEP - POWER ON. These are buttons on the icon shown in Fig. 1.
On the screen there will notice SERVICE (FACTORY).
In the service menu has four entries:
•? Test Pattern - test image;
•? Adjustment - adjustment;
•? Reset - reset.
•? Option Bytes - Bytes options;Positioning is accomplished group of buttons CHANNEL: "Down Arrow", "arrow".
In this case, when replacing the tube, you will need only two modes - a Test Pattern and Adjustment.
Elect mode Adjustment. Pressing on the button UP (more) or DOWN (less), VOLUME (volume), vlezte
in this mode. On the screen there will table the main parameters of the adjustment.
Movement on the table is being implemented button "down arrow", "arrow".
Explanation of adjustment parameters outlined briefly on the screen in capital letters, is shown in the table.
Selecting and setting the adjusting of its range specified, according to
table, is being implemented buttons (volume) VOLUME, (more) UP or (less) DOWN.
The values ​​of the functions of all recorded non-volatile memory will be when you exit Adjustment or shutdown the machine.
Before adjusting the record necessarily matter what the parameters were to change.
This
is due to negative images come in handy - you can always go back.In the
author outlines the episode had to change the settings: AGC, SCT, SCR,
SBT, RC, GC,
RG, Sun, BG and PHS. The parameter values ​​of all adjustments to the modification and after are shown in Table as well.
Test Pattern mode to control the correctness of the information is needed and light adjustments
color purity. For the parameters of the position of Test Pattern accessed while connected
mode of service by using the CHANNEL: Ti. The cursor must move on
Name Test Pattern. Then click on the VOLUME button. The screen name may seem
Test images: RED - red screen, GREEN - green screen and BLUE - blue screen.
When choosing a color, we estimate the uniformity of the radiance of the screen.

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

Fig. 1. The icons in the menu buttons to enter service
Provided that in the apparatus to replace the tube were not violated, and adjust the main
CRT does not differ very new to the parameters of long-time, adjustments to what was
described
above, it is quite normal to get an image. In some cases,due to
differences in the parameters of the geometry of the deflection setting
the correct image is required.
Alignment and vertical size trimmer and regulated VR3O1 VR3O2. For
adjustment in the horizontal dimension must pick up the capacitance S402 (7200 pF, 1600).
To increase the capacity to increase the clearance needed to lower - lower. As delineated
episode had lower capacity of S402 up to 4700 pF. Centering horizontally adjusts the menu service parameter PHS.
New picture tubes on the market come bundled with the system deflection (OS) and device
magnetostatic (IAS) and represent a node, which regulates the manufacturing plants.
All components of this complex together with each other tightly, and in television included,
do not require nearly the attention control rays and color purity.
However, due to the disruption of attachment of the deflection, the displacement device mag
or in the case of CRT, in the use of the former, as well as picture tubes,
restore the past by mounting them on the latest electro-optical projectors
(EOC) may require adjustment of the information light and color purity.
To carry out this procedure need proper installation and adjustment of the deflection
magnetostatic devices. To do this:
• Put on the CRT deflection system and tighten the clamp screw previously;
• Put on the CRT device information magnetostatic and place it as shown in Fig. 2 shows;
• Switch the input of the apparatus with the television signal generator "white box";
• perform a complete demagnetization of the TV with a loop
external degaussing;
• controls the contrast and brightness set to maximum;
• disconnect the blue and red light. Loosen the clamp screw holding the deflection system;
• try to ensure the alignment of the deflection along the neck tube of bright spots on the screen;
• a green spot, set in the center of the screen;
• Two-pole magnets pushing the color purity with respect to the magnetostatic devices
each other, try to achieve optimum purity of color, if possible, the whole area
screen, alternately shifting the system along the neck of the tube deflection and adjusting magnets
color purity (the location of the magnets in the device magnetostatic in Fig. 3 shows);
• OS turning on the tube neck, reach to one side parallel to the raster
are the edges of the frame, and attach the clamp operating system;
• in the anterior lobe of the operating system, insert tightly and stick the rubber klinyshkaa four for more
strong attachment OS.
Adjusting the static information is as follows:
• serve on the input device signal "field mesh";
• decrease the contrast and brightness achieve probably the smallest width of the vertical and horizontal lines;
• Focus control on TDKS focus the beam of green produce;
• Includes red and blue beam;
• adjusting a pair of lugs 4-pole magnets and is changing the angle between them, combine the blue
and red vertical lines in the central part of the screen;

turning at the same time both ears, the angle between the retaining
connect the blue and redhorizontal lines in the central part of the
screen;
• adjusting a pair of lugs 6-pole magnets, we reach the line combining the red and blue with
green line;
• Change the angle of impact on the vertical line, and turning the magnets of both - on the line horizontal.
Since the 4-pole magnets and 6-pole have a mutual influence, useful to adjust
several times repeated.
After the static information Check purity of the color blue, red and green
rasters visually, using a test image menu service. If the image
correct, this information control rays and color purity is completed.
In conclusion, the quality of the image taken by the channel estimate. In some cases,
eliminate ghosting and lines of the rays have to adjust the reverse voltage regulator Screen for accelerating TDKS.
We hope that the material provided by the articles will help to quickly make repairs
system, needing to replace the picture tube, as well as adjustments in the service menu to understand
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات: 2241
تاريخ التسجيل: 16/06/2010
العمر: 54

مُساهمةموضوع: رد: سرفس مود SAMSUNG   الخميس يوليو 21, 2011 11:20 pm

CHASSIS SCT12B:
with push buttons control the following sequence: STAND-BY -> P. STD -
> HELP -> SLEEP -> POWER ON. Exit button or HIDDEN STATUS.
CHASSIS SCT13B PIB SCT11D
In the standby button on the remote control pressed in sequence the following: P. STD. HELP. SLEEP. POWER ON.
message appears: "SERVISE (FACTORY)".
Service mode (SERVISE MODE) consists of the following areas: Pattern (test mode);
Test Option Byte (installation option); Adjustment (adjustment); Reset (Reset).
Choose the option buttons V.
Parameter will change the keys - and +.
After exit from the service stored data automatically.
To activate the Run Aging Mode button pressed twice HIDDEN, disable mode again by pressure HIDDEN button.
[b] Chassis SCT-51A [/b]
Input: 1. (Picture off); 2. (Sleep); 3. (P.std); 4. (Mute); 5. (Picture on);
Exit: off - food.
The service menu of the 5 sections is: ADJUSTMENT (regulation), TEST PATTERN
(Signal
model), OPTION BYTE (option byte), RESET (reset) and BONUS (control
special video channel). To exit the service push the button STATUS
or elect RESET position and then push the button VOL (+) or VOL (-).
Chassis SCT-52A
Alternately, push the button on the remote PICTURE OFF -> SLEEP -> P. STD ->
MUTE -> PICTURE ON. Move cursor to the CHANNEL and VOLUME.
Choose buttons CH V option.
Adjust buttons + VOL-value.
Parameter is memorized automatically.
Install a jumper between pin 5 of the microcontroller (MC) and mass. At the same time
green LED brightness must be increased.
Shake the MODE button on the remote. In the upper left corner of the screen display will appear the color of blue "SERVISE".
Shake the remote control button a second time MODE-service mode is turned on. Choose the Options button
CH V. Change the buttons + VOL-value.
Settings are automatically stored.
You should not set the values ​​of the extreme AGC and AFT, as there will be noise in the image, image failures.
CHASSIS SCT57B
1. Television in the operating mode is enabled.2. press the remote control (DISPLAY).
3. hidden button (factory) to press the remote control.
CHASSIS SCT57B
1. Television in the operating mode is enabled.
2. press the remote control (DISPLAY).
3. hidden button on the remote press (factory).
Z68SHASSI
(AV) (SLEEP TIMER) (POWER). Exit: POWER OFF.
Z70 CHASSIS
To enter the service to 1. button press (HIDDEN) - on
remote hidden 2. quickly press a sequence of (stand-by) III. (P.std) 4. (Help) IV. (Sleep) VI. (Power-on).
SC WP 6271 Models
To enter the service menu press the button or press the HIDDEN very quickly
the following sequence of keys on your remote control: STANDBY, P. STD, HELP, SLEEP, POWER ON.
CHASSIS KS2A
A. (STAND-BY) W. (DISPLAU) C (MENU) D. (MUTE) E. (POWER ON)
CHASSIS R1V.
push buttons in series: 1. STAND BY, 2. P. STD, 3 HELP -?, 4. SLEEP, 5. POWER.
Exit from the menu: STATUS.
S15A CHASSIS.
To enter service mode need to:
• TV mode to include in the work;
• Press the button on the remote control with logo hours Sleep;
• the remote control button hidden (factory). On the screen there inscription: ADJUST OPTION RESET.
Adjustment buttons by V-, V +, P, P +, and an introduction to the memory buttons Sleep.
The values ​​of the AGC - 9, SBT - 8, SCT -10, VCD - 80, SCR-10, SC-12, RG -47, TSC -13, BG - 34
CDL - 4, GG -32, PSL - 32, PVS - 32, LU - 0, PHS - 40, PVA - 42, OPTION
not to touch the better. Exit from the menu: 2 times Factory
CHASSIS SCT11A, B:
Click here to console the following sequence of buttons: 1. STAND-BY -> then 2. P. STD ->
then 3. HELP -> then SLEEP -> then press 4. POWER ON. Output from the service STATUS. Under the panels
hidden button panel is HIDDEN. With this button you can enter and get out of servisnogomenyu.
GENERAL
Unable to enter the menu. On-screen message "HOTEL MODE ON"
Reply
To exit the locked hotel ("HOTEL MODE") must be in standby mode (Standby)
on the remote press the following button sequence: DISPLAY - MENU - POWER. Buttons to push

should be one, pressing at the same time not be two buttons, a pause between strokes
neighbors should be minimal. In that case, if the regime is a way to disable HOTEL MODE
this is not possible, we recommend you go to one of the service centers authorized Samsung Electronics.
TV, Samsung has come from a combination of:
Option 1: The button is hidden (HIDDEN) on the remote
Option 2: 1. Stand-by-> and then 2. P.STD-> then 3. Help-> then 4. Sleep-> then 5. Power-On
Option 3 then 1. PICTURE OFF - then 2. then SLEEP - then 3. P. STD then -4. MUTE - then 5. PICTURE ON

* * *
TV Samsung CS-21V10MJ,
LC863532C-57Z0. VPU-LA76818A,
HOT - 2SD1879, EEPROM - 24C08, Tuner - VS8-1G5-BG - pyativoltovy, UPS - 2SC3886A
+ C2655 + A1015, HR - STV9302B, remote control - 55K3 = 54P4 = 5Z26 = 55K2.
Entering the SERVICE - hidden button on the remote control, it is permissible, and flipping pages menu.
Information on how to change remotes: 5Z26 = 54P4 = 55K3 = 55K2 (in the native remote printing).
* * *
TV Samsung CS-14Y53R,
KS1A chassis, microprocessor TDA9381PS/N2/3I0753
Entering the service menu: fast dial STBY-,
then DISPLAY-, then MENU-, then MUTE-and at the end of POWERON
* * *
TV Samsung CS-21FSR.
KS1A21F5
Chassis. CPU TDA9381PS/N2/310753. Version SPM-802EEN2.
Memory 24S08. Tuner TECC0949PL35A (S). Mono.
Log into the service menu: switch to STAND BYbystro press
DISPLAY, MENU on MUTE and then turn POWER ON. No TXT. Russian est.Sekam there.
* * *
chassis KS1B,
Processor TDA9381PS-N2-3I0753 K1K152 CB1134 SPM-802EEN2.
Can be replaced without alterations in TDA9353PS-N2-3-0568 K2J468 CB4090 SPM-812EE.
Entering the service menu: press consistently DISP-MENU-MUTE-POWER.
* * *
Video recorder apparatus (S17A) Chassis Samsung TX-14N3DF,
Russian menu + MULTISYSTEM. Processor: TDA 9361PS/N2/4/0717, Memory:
24C16, HR chip: LA 7840, the VLF: TDA 7267A, TDKS: FTK 21H001,
Tuner VCR: TEDE9-247B, video amplifier: TDA 6107, TV Tuner: TEDE9-802B,
Entering the service menu: go into standby mode STAND-BY, etc.
DISPLAY, then MENU, then MUTE, and the last POWER-ON.
* * *
TV Samsung SM14H4MJ.
The inscription on the chassis

  • LA76931-A, CPU LA76936Y 7N-58T7. UOC - LA76936Y 7N-58T7,
quartz ZQ1 - 32.768 kHz, ZQ2 - 4,433619 MHz, EEPROM - 24C08A, KR - LA78040,
HOT - TT2190, ULF - TDA2003, Tuner (5 Volt) - VS1-1A5-BG, FBT - BSC25-T1010A.
The Internet UPS is described in detail (typical "Chinese" trehtranzistorny)
as well as circuit design and fault characteristic CD, CP and UPS.
Full-time remote control - 55K9. Analogues of the remote control:
5Z51 = 54B3 = 05D5A = HX55K8 = SYZ = 53W3 = 57L8 (Sharp) = KLX-55K9T = (Panasonic) = 50JI LW-55L7 = 52E5.
Entering the service menu with remote staff - the remote button is added finalized, direct entry into the service menu:
1st Pressing - on the TV FACTORY
2nd Pressing - on TV B / W BALANCE
3rd squeezing - the TV service menu sections (1-20, see below)

4th squeezing - the TV BUS OPEN
5th squeezing - a return to normal mode
Menu (and the user and service menu) is very similar menu to the microprocessor LC863532C-55K9, previously described.
"The Trap" service menu: The ADJUST MENU 3 (sub-third s / m)
SETUP SELECT is set to "1" because at a value of "0" -
only sections of 0 ... 3, while "1" all sections 00 - 20 are disclosed.

For the record
1. TV without the EEPROM starts, the SR and CR are working but no picture-black screen.
2. C EEPROM «clean» (FF) TV over 5-7 seconds starts, TV
functional entirely in AUTO setting all available
programs going on (with the correct location of sub-bands), in
Unlike microprocessor-xxxx series LC863hhh already included
Secam (is there). The foregoing accurately shown for the composition of the chassis.

* * *
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات: 2241
تاريخ التسجيل: 16/06/2010
العمر: 54

مُساهمةموضوع: رد: سرفس مود SAMSUNG   الخميس يوليو 21, 2011 11:22 pm

TV Samsung 15 "Flat
- LA76936Y SUSOC 7N-59J3,
Personnel: LA78040N, FBT: BSC25-0146, Microprocessor: LA76936N7N57T5E
(CKP1510S), Sound: TDA7253, tuner: ETA-SF03/12, Remote: KK-Y271A. TV is equipped with
Remote control type 56S8, 55K9, 54D5.
Entering the service menu hidden button (remote finalized)
* * *
TV SAMSUNG "14" China.
Processor: LA76936Y SUSOC 7N 59J3
9GA91, Tuner: DWE-8051LONGSIGN. Remote Staff: ZY-55K9R F. Rally driver,
24S08postavil clean. Through the service menu all pulled out.
Entering the service menu: remove the volume to "0" then press "MENU" and code
6568. The screen will appear the inscription: "FACTORY". Buttons "SLEEP", you can choose
two modes of "B / W BALANCE" and "ADSUST MENU" button in the same mode "MUTE"
personnel can be turned off in the second page scrolls.
Exit: push button "RECALL".
To clear the memory, after turning off the machine, the Russian language was a constant,
it must choose, when the service is enabled. Otherwise, after you disconnect from the network, English
constantly pops up.
* * *
TV SAMSUNG CS-21K9MJQ, CS-21K2MJQ
and others on KS9B chassis.
Entering the service menu: standby mode press DISPLAY, the menu, then MUTE, then POWER ON.
* * *
TV SAMSUNG CS29Z47Z3Q, KSDA chassis.
Mikroprotsessor-TDA12120H/N300 (SI6826.1 CK8094), HR-LA78045,
Quartz-24.576 MHz, the UPS-STRW6750F, HOT-TT2206, video amplifier,
TDA6107AJF/N1, VLF-TDA7297SA, block skv-TDQ-6L/125S (AA40-10007A),
TDKS-FQH29A003 (AA26-00289A), Memory-24S16, picture tube-A68QGX793X601.
Entering the service menu: button Power OFF, then Info, then Menu, then Mute, and finally the Power On.
* * *
TV Samsung, chassis KS-3A 50Hz.
Model CW-25C33N processor SDA5555 A035 (SIM-806HMA7), VDP3120D
model CW683CN processor SDA5555 A015, VDP3112B
Enter the service mode, pressing Stand-by, then Display, then Menu, Mute, and then Power ON
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

* * *
TV Samsung. Z70 chassis.
Enter the service mode: remote control with the usual, with the set
jumper between the 17 O (KEY3 scheme) management processor
P87C054BBP apparatus and mass. If there are jumpers commands from the remote, as service, are accepted.
* * *
TV Samsung CS29Z47ZQQ
Enter the service mode: mode of duty, key info, button menu, button mute, and vklyucheniepower on.
* * *
TV Samsung CK-7271, CK-6271.
Z70 chassis. Written anywhere that you are logged into the service menu via remote service.
Take a typical, assort, payaem diode between 5 and 21-pin chip on 21 foot cathode and enter the service mode.
* * *
TV video recorder: Samsung TX-14N3DF (S17A) Chassis.
Microprocessor: TDA9361PS/N2/4/0717, memory EEPROM: 24C16.
Enter the service mode: STAND-BY, then DISPLAY, then MENU, then MUTE, and finally POWER-ON
* * *
TV SABA M6317E,
brought from Germany, TX807CS chassis
CPU TDA9554PS/N1/1/0301 K0J009 CA1737 IVV 2.20, an audio processor MSP3415D B3, memory 24W04.
Entering the service menu: go to stendbay, the network turned off. On the remote
txt push and hold, the network included. If the home console is not, then the MAC codes 1272, 1320.
* * *
Apparatus SANCAI SC-2588A,
Microprocessor:
TOSHIBA-HAY-26 TMPA8891CSCNG6V12, ZQ - 8MHz, Tuner-
LONGSIGN DWC-8053V, EEPROM - 24C08, HOT-C5302, TDKS -
BSC27-0213A, ULF - 2xUTC2003, IC CD - LA78041, UPS chassis
3Y01 similar ("Chinese" trehtranzistorny), C5302
BCK-4901A (BCK-150-01)
Entering the service menu: a button hidden FACTORE (under
buttons PP), as well as written in the service manual.
TV ELENBERG 2185,

CPU 8821CPNG5UU5,
EEPROM 24C16A, personnel IC STV9302A, BP-discrete for
S5586, the VLF TDA7496SA, tuner UVC68K9VCK 0504-6155 A-T9XX0330B
One leg AGC, two leg voltage VT. 0 to 30v, management
-ranging from 4 and 5 feet. 4v 4 nozhkea. and 0v
5 pin = VNF L, 0v 4 pin and 5 pin 4v = VNF H,
At 4 and 5 feet in 4v = UNF, 6 foot 9v, 7,8,9,10 legs - no, 11 foot - IF.

Entering the service menu: 1) the volume set to min.
2) On the volume (-) and press the button on the display.
* * *
Sanyo CE 14SA4R
(Kaliningrad assembling, 2005): CPU - LC863448S-55S6,
The video processor - LA76818A + LA7642N; CD - LA78040; VLF - LA4266; NOTES - TT2138;
Remote control - JXMYA (ICs in the remote control - M055155 (5031A) - 20-Nogai planar chip) or
one of the above is not compatible.
Entry into service: holding the «MENU» (on the remote) to press «VOL +» on the TV.
Flipping through the options button on the remote control «TIMER» and «MUTE», change the parameters
- «VOL-» and «VOL +». Options service from 00 to 93 - and without the manual are clear, and then
once the transition is a 300 option, and so on - and in them "?".
The unit came with a diagnosis - video input does not work. Troubleshooting - to enter service
and the option "87" (87 AV123) switch with a value of "0" to "1", after which
exit the service menu to press «MENU» on the remote and turn off the TV network button.
After connection - options in force will.
* * *
SANYO: CE21KF8R,
Kaliningrad issue. Chassis: FC-3B (FC3B - in the corner of the board
inscription from the outside). The board sticker that says: C5GS - soft,
presumably. Service, for a very lazy: simultaneously push on the remote control MENU button and the panel VOL +.
* * *
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات: 2241
تاريخ التسجيل: 16/06/2010
العمر: 54

مُساهمةموضوع: رد: سرفس مود SAMSUNG   الخميس يوليو 21, 2011 11:23 pm

TV Sanyo CE28SW01
VECO chassis U99.190-07. Processor OM8363H/n3/4 VATXMO CC6616.
There is a DK and SECAM, the service is included.
Enter the menu service: enter menu and press the code sequence 9301.Vyhod: buttons nil.
* * *
TV SANYO: CE28/32WN3, EB5-W shasssi processor: SAA5563PSM30053.
Log into the service menu:
1) push button keypad panel VOL-local and, holding it down, push the green button Teletext.
Confirmation of the entrance shows the appearance on the screen the main service menu with a list of sections of adjustment:
GEOM 4:3
GEOM NATW
GEOM 16:9
VIF, etc.
Initialize EEPROM Flash memory:
To initialize the read-only memory is the inclusion of a
All data required for proper operation of the machine. It must be carried out in case of a new memory chip.
To commit the following steps to perform the initialization:

  • enter the service mode.
  • MORE sub-menu trigger.
  • With the help of buttons P + / - INI NVM position to choose.
  • Confirm the selection button VOL +.
  • the service mode and exit from the network switch off your TV.
  • connect the TV stations and programming.
Adjust service:

  • Buttons P + and P-use to navigate through the menu service.
  • With VOL + buttons being implemented in the input preferred by sub section.
  • Changes in parameter values ​​buttons VOL + / -.
  • MENU button is being implemented to return the previous menu (if
finding the service menu in the main pressure on the button MENU exits the service mode.)

  • Use the number buttons 0 ... 9 Integrating done directly selected parameter values.
The choice of a main service menu allows you to position GEOM 4:3
carry out the necessary adjustments to the geometry of the image format
4:3 screen position GEOM 16:9 - to 16:9 screen, GEOM NATW
- For a widescreen TV (Natural Wide format). List
parameters, as well as their sizes for different image formats, is shown in Table 1.
VIF Submenu:
Allows you to adjust the hold, the channels of RF and IF related.
PLL demodulator signal - PLL ...... 80.
PLL demodulator signal for the standard L'-PLL'L ...... 80.
AGC-AGC ...... 16: Apply the input device in the middle range
UHF band signal level of 60 dB / uV. In the service setting
AGC choose. Adjusted to achieve a voltmeter 3.3 + / -0.2 V.
PLL loop time constant - FFI ...... OFF: ON is liboOFF.
G2Submenyu:
Allows you to adjust the voltage of the accelerating tube to conduct.
The brightness level at the voltage of the second grid tube -
BRI ...... 0: When the voltage of the second grid, this option should always be set to 0.
ADJ - Installation of service lines: a potentiometer to adjust to accelerating the emergence of a service line on the screen.
On / Off function AKB - AKB ...... ON: ON is liboOFF.
The level of control RGB - K-DRV ...... 4 (CRT 32 '), 3 (CRT 28'): keep the initial values.
MORE Submenu:
Allows you to adjust video channel to pursue.
The delay of the luminance signal in the PAL system - Y / C PAL ...... 3.
The delay of the luminance signal in the SECAM system - Y / C SECAM ...... 0.
The delay of the luminance signal in the NTSC system - Y / C NTSC ...... 3.
The delay of the luminance signal inputs for AV - Y / C AV ...... 10.
The rate of reduction of contrast-PBL SPEED ...... 0: initial value of the preserve.
Contrast signs OSD - CONTR OSD ...... 0.
Image contrast teletext - CONTR TXT ...... 0.
Mute SEMI MUTE ...... 15 -: keep the initial value.
Do not install - AUTOW THP.
Initialize NVM memory - INI NVM (see section''permanent''memory initialization).
CONFIG submenu:
Allows configuration options to set the TV.
On / off comb filter - CMB ...... OFF: ON value or OFF.
Set of characters teletekstovyh for Eastern Europe - TXEAST ...... OFF.
Mode voltage vacuum tube high - OSO ...... OFF.
Trademarks-OEM: OFF (for SANYO), ON for other firms.
Models for the British market - URMKT ...... ON. UK ON.

S-STAT, V-STAT, I2C BUS Submenu:
Allows you to read the status and I2C BUS position makes a valid lock on I2C bus.
production mode FACTORY MODE:
Production mode for the consumer is not. Its purpose
is the introduction of the TV mode, which simplifies the process of conducting
production. It is displayed in the form of FAC messages.
In contrast to the normal operation mode is characterized by the production features the following:

  • Standby mode is absent (STANDBY).
  • In the case of dropouts blue background is not displayed.
  • Adjustment of the consumer (brightness, sound, contrast, etc.) faster than four-fold effect.
! If the device meets with production activated
mode, you need to get out of it by connecting, and then turn off the menu, with facilities-related hours.

Mode and RENTAL HOTEL:
used if necessary to limit the possible installation TV (in a hospital, hotel).
Both regimes are characterized by the following features:

  • the highest level of the sound level is limited, pre-installed with the introduction of the device in this mode.
  • There is no chance of programming.
  • TV is always included with the values ​​normalized, which can not be changed.
  • Disabled (Child Lock) locks of programs from children, as well as the function of election language version.
  • You can connect your TV enforced in AV mode to one of the programs an ... 8.
To connect the TV and HOTEL RENTAL mode should be performed:

  • push and hold the VOL-button on the keyboard panel locally.
  • Hold the button to press VOL-button on the remote control RECALL.
Confirmation enter the hotel HOTEL message on the screen will be: HOTEL: 00
where:

  • first digit (0) characterizes the TV mode (0 - normal mode, 1 - HOTEL mode, 2 - RENTAL mode);
  • figure describes the second program, on any TV
was installed after it is connected (0 - a program chosen
before switching off the TV, 1 ... 8 - channel number, 9 - Connection mode AV).

! 1. Mode RENTAL HOTEL from different only in that the buttons VOL + / VOL-- active.
2. To exit HOTEL RENTAL regime or to the color saturation level at nil to install.
Mode self-test:
In this mode, the map probably some problems.
The microcontroller continuously monitors some chips. If you find a defect protection scheme put into effect.
Exposure of the fault is determined by the number of blinking LED (error number), see Table. 2.

Exit from service: push button MENU, if the TV is in
service mode is displayed at the main service
menu button or any remote control (which is not used for maintenance treatment service), if the sub-menu is activated.
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

* * *
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات: 2241
تاريخ التسجيل: 16/06/2010
العمر: 54

مُساهمةموضوع: رد: سرفس مود SAMSUNG   الخميس يوليو 21, 2011 11:24 pm

Apparatus Sanyo CE27LC6-B UK4A shassis.
Processor TDA15633E/N1B00, remote JXPTA.
Enter the service mode: On the machine on the remote press:
green button on the TV and p-. The sound of 248 bar is set to 0 bits.
* * *
TV SATURN ST21NF1D, ST 21NF2, ST1422, ST2199.
Chassis 3S10 - alternately on the remote to press the button: «MENU», then
«AV», then «ANAL». Turn the pages click - "OK" Exit from the service -
the button "PP" Chassis 3Y01 - alternately press: Menu, then Menu, then
Qviwe, and the last Mute. Turn the pages click: Timer. Exit: Menu.
* * *
TV SATURN ST 1418, ST 2539, ST 1401, ST 2101, ST 2139, ST 25NF1, ST 2939.
Entering the service menu: The volume on the TV to remove the "0" and press the button on the remote control «Display».
* * *
TV SATURN ST 2939 (5N11shassi).
Occurrence
in the service menu: Turn off TV, put pressure on the control panel volume «VOL +» and «VOL-« and connected TV.
* * *
TV SATURN ST 2132SF.
For this model requires a special SERVICE PANEL.
* * *
TV SATURN ST 29F1 (5N10 chassis).
Entering the service menu:
Menu № 1. turn off TV, put pressure on the control panel «VOL +» and «VOL-« and TV plug.
Menu № 2. turn off TV, put pressure on the control panel «PRG +» and «PRG-« and connected TV.
* * *
TV SATURN ST 29SF1 (5P60 chassis).
Push
in turn buttons on the remote control: CLOCK, then PM , Then the timer.
Exit the menu button viewer channel number.
* * *
TV SATURN ST 1401 ST 1402 (M28 chassis).
Entering the service menu: The volume on the TV to remove the "0" and press the button on the remote control «Display».
Exit from service: "OK» Factory OFF.
* * *
TV SATURN chassis M113.
Login: Volume on the unit to move to "0" + button on the remote control «Display».
Exit from the menu of service: "OK» Factory OFF.
* * *
TV SATURN ST21F1
Microprocessor TDA9381PS/N3/2/1973.
Enter the service mode: on the remote to press MENU, then dial 8500. In the left
upper right corner of the red M will appear, choose the sub-numbers 0 to 9 and then push MENU. Exit: Press the Standby twice.
* * *
TV SCHNEIDER, DUAL: STV 6156, TV 1170, DTV-2shassi processor: CCU 2070.
Digital cameras based on the DTV-2shassi, SCHNEIDER firm.
Log into the service menu:
1) on the remote control push buttons at the same C button and a service
that is hosted in the bottom row of the remote control.
2) Release the button service.
3) to press a numbered button arbitrary.
Confirmation of entry into the service mode the message is: SEVICE MODE
Service adjustment:

  • election parameters low tone buttons.
  • Adjusting the settings buttons VOL + / -.
  • Remembering the button T (IDEAL).
If the designation of controlled functions, should be low after a large
letters, this indicates that the adjustment accurately realized.
The appearance of the second largest capital letters indicates that the coarse adjustment.

  • simultaneously squashing TELETEXT button and click a service, you can
horizontal position of text on the screen to adjust the menu
TXT SERVICE MODE. Before entering this mode should be in the position of TV is TV.
Adjusting the Text button VOL +, VOL-to implement and preserve the memory of the set of text buttons T.
1. Horizontal Frequency - SP: Adjusting to the lack of wrapping the image.
2. Center Horizontal - BP.
3. Center vertically - AO.
4. Vertical Size - HO, Ho.
5. Linearity - SO, So, SI, Si: Adjust the screen relative to the middle.
6. Horizontal Size-YO.
7. Correction of image geometry - ZO, Zo, PO, Po: Switch
ZO function for two, set by the geometry of the PO. If
pincushion distortion correction is extremely large, ZO switch
3 and over again to adjust PO. If distortion correction is not large, ZO adjustment should be reduced and PO recover.
8. Correction of pincushion distortion - ZI, Zi, PI, Pi.
9. The frequency of color in PAL - SA: set to PAL in the middle
limits the frequency of color. Adjust to stopping the movement of bands of color.
10. G2 - contrast and brightness: Set the contrast and brightness
best between the minimum and maximum position, G2 adjusting.
11. Static white balance - CR, CG, CB: Before adjusting
correct
to install G2 (all shades of brightness). Components R, G, B set so
that the gray glow of the dark parts of the image obtained.
12. Dynamic White Balance - DR, DG, DB: Adjust the color of
dominant, having a white glow bright fragments of images.
Exit from service: press on the remote TV.
* * *
TV SELECO.KU6360.
chassis FCP
2001. TDA 9364PS/N1/3S0509 TWIST 25, sound-multi, secam-No.
Entering the service menu: press M on both the TV and incl. on the remote.
Remote control - right from Philips.
* * *
TV SELECO A28SS575
PC220 chassis. (100Hz) (Formenti-pricol)
Technology entry into the service mode in the absence of the original
Remote control: it is necessary to register in the EEPROM at 03S3 odd (01, FF)
* * *
الرجوع الى أعلى الصفحة اذهب الى الأسفل
 

سرفس مود SAMSUNG

استعرض الموضوع السابق استعرض الموضوع التالي الرجوع الى أعلى الصفحة 
صفحة 1 من اصل 1

 مواضيع مماثلة

-
» احدث موبيلا ت السامزونج Samsung S8500 Wave
» samsung star wifi gt-s5233w
» طريقة اظافة العاب و برامج على جوالات SAMSUNG اظافة لأكواد
» هاتف بكاميرا عالية Samsung Pixon12
» كود رفع الصوت SAMSUNG SGH-J700

صلاحيات هذا المنتدى:لاتستطيع الرد على المواضيع في هذا المنتدى
أشرف عثمان للإلكترونيات :: -