أشرف عثمان للإلكترونيات
أهلا وسهلا بكم ونتمنى أن تستفيد معنا


schematic-VIDEO CASSETTE-monitor-service manual SHASSIS Panasonic Philips SAMSUNG SANYO SHARP SONY toshiba Aiwa AKAI DAEWOO Goldstar HYUNDAI VIDEO Grundig Hitachi JVC LG Mitsubishi National NEC ORION VESTEL Corus-Repair-Plasma-LCD
 
الرئيسيةالتسجيلدخول
https://twitter.com/ashraf69osman--- https://www.facebook.com/ashraf.osman.73-- https://plus.google.com/u/0/+ashraf5914

شاطر | 
 

 سرفس مود - HORIZONT

استعرض الموضوع السابق استعرض الموضوع التالي اذهب الى الأسفل 
كاتب الموضوعرسالة
MSA
مشرف عام
مشرف عام


عدد المساهمات : 542
تاريخ التسجيل : 16/06/2010

مُساهمةموضوع: سرفس مود - HORIZONT   الثلاثاء مايو 03, 2011 11:28 pm

shassi11AK19S 51/54CTV-664 Proc. VESTEL 1919 v1.0
Login
press the blue button on the remote control. Dial by pressing the
numeric keys 4, 7, 2 and 5 remote control. Appears on the TV service
menu. To exit the Service menu, press the blue button or the "TV" remote
control. In the service menu, there are two modes: properties and
settings.
output- POWER OFF

Chassis 11AK30 CTV-664.
Login
To activate the adjustment mode, press the blue button remote control, while on the TV screen should appear INSTALLATION menu.
Press
the Set button 4,7.2 and 5 remote control. Appears on the screen menu
to select the desired settings, press the button "P +" or "P" remote
control to change your selections, use the buttons "+" or "-".
red
button (only for stereo models): AVL switch to ON or OFF modes in the
service menu. In the service menu shows the word AVL, AVL mode when ON,
Green
button toggles the aspect ratio to 4:3 or 16:9 in the service menu.
Especially necessary when setting up the vertical dimension of the
picture mode to 16:9.
Yellow button toggles the mode vertical scan disable. Used when setting the accelerating voltage.
The blue button is used to automatically adjust the AGC and IF in the service menu.

model 54DTV-700, 710 Proc. CCU3000 SDIL
Login
- Adjustment of "volume" set to "On";
- Press on the remote control mute button,
- Press the button on the remote timer.
Adjustments in the "Service" radio button "P +" / "P" in a circle. The value of the setting, change the "+" / "-".
Remembering the values ​​of the adjustment is made separately for each of them by pressing the green button on the remote.
TV output

model 51/54STV-730 Proc. TDA9351
Login
In
the off button "AV" (TDA9351 Pin 7 shorted to ground through a resistor
670 ohms) on the front of the TV and hold it down (before the
subsequent images on the screen), simultaneously press the button and
the "Network". On-screen message should appear CTS MONZA IF38.0, AFC3,
indicating that switch on the "Tools"
output- TV

model 54CTV-730-I-9 Proc. TDA9381PS/N2/1I0840
Login
From standby mode press the remote control (DISPL) (MENU) (MUTE) (POWER ON)
Exit - TV

Chassis 14.2 63/70STV-698 Prots.TDA9555H
Use the remote with the code RC-5 with a separate control
contrast, brightness, saturation (using "+" and «-»).
Login in service: when the TV button on the remote with the code RC-5
click "Contrast -". The other adjustment in the service
mode are made with the native console.
Exit the service mode: on the remote control code RC-5 press
click "Contrast -".

model CTV670
Login
If you turn the TV on the front panel or remote control button «AV» and
holding it, turn on the TV button "network". Button «AV» keep up the
appearance of a raster. You should see IF38, 0 AFC3, Settings button "P
+", "P" and "+", "-" Exit- «TV»

Model 670/676/690/730 Proc. SAA55XX, TDA93XX, R83S055
Login
take control RC7-2 or any other on the m / c PCA8521Bt/040.
To conclusions 3 and 11 to connect the additional button to "ON. SERV. Dir."
output- TV

Chassis CTV-19733 21BF22 percent. TDA9353
Login
option 1
- The closure of technological XN102 jumper on the chassis. Short the
jumper to when the TV is in standby mode or view programs.
Option 2
- Filing with the remote control in the RC5-code with the address of
the system 7 and the command code 58 (the figures given in the decimal
system). Command to apply when the TV is in standby mode or viewing
software.
Option 3 - By pressing buttons, DISPLAY, «SL», MUTE, POWER remote control in the standby mode. output «TV» or «AV».

model 72DTV-694DTI-18
Login
Turn
on the TV in the working mode, for then click "Network" on the TV front
panel (LED lights up red), then click the button to switch channels "P
+" or «Ch +» on the front of the TV or the remote (the LED turns green).
Put the switch DVD-TV on the remote to TV. After the image appears,
click the "Menu" button on the remote control (Table menu appears),
while in the "Menu" button press sequence 1,6,7,5 - service menu will
appear in the form of tables with colored heading. To save the output
settings, click "OK".
output- TV

Chassis SHTST 739 M1, 21A21, prots.TDA 9381/N2/1/1277
login
POWER OFF, DISPLAY, MENU, MUTE, POWER ON.

M28 chassis 21EF05 prots.8821CPNG4U88
Login:
Volume on the TV panel to "0" + button «Display» button on the remote control.
Output: "OK» Factory OFF
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس مود - HORIZONT   الأربعاء يوليو 20, 2011 6:41 am

HORIZONT




* * *

51 \ 54CTV-664


TV 51 \ 54CTV-664 are collected in a universal chassis 11AK19S. In TV
chips are used to control the bus HS. This allows for adjustment
TV directly from the remote control, without removing the rear cover. Therefore,
if the TV works, but it disrupted consumer characteristics (changed the balance
white, image size, centering the image, etc.), it is necessary to try
adjusted with the remote control.
5.1 How to enter and exit the service menu
Sign in MAIN MENU by pressing the "blue" button on the remote control. Dial by pressing the
numeric buttons 4, 7, 2 and 5, the remote control. Appears on the TV service menu.
To exit the service menu press the "blue" button or "TV" remote control
Control. In the service menu, there are two modes: properties and settings.
5.2 How to use the mode properties (ADJUST) SERVICE MENU
Enter the service menu. Move the selection to a strip bar properties.



* * *

5 METHODOLOGY chassis settings 11AK20S

TV 37CTV-664 are collected in a universal chassis 11AK20S. In
TVs are used to control chip via I2C. It
allows adjustment of the TV directly from the remote
controls without removing the rear cover. Therefore, if the TV works, but
disrupted consumer characteristics (changed white balance
image size, centering the image, etc.), it is necessary
try to adjust with the remote control.
5.1 How to enter and exit the service menu
Sign in MAIN MENU by pressing the remote control. Press
numeric buttons 4, 7, 2 and 5, the remote control. Appears on the TV
Service menu (SERVICE). To exit the service menu
Press button or "TV" remote control.
In the service menu there are two modes: ADJUST
(SET) and OPTIONS (PARAMETERS).
5.2 How to use the mode ADJUST (SET)
SERVICE MENU
Enter the service menu. Drag strip of choice (it
has a darker hue) on the line ADJUST, using the buttons or
.
Press the "-", "+" selection. The following
parameters are displayed simultaneously:
1. AGC - Automatic gain control;
2. VA 1 - vertical size for size ratio 4:3, 50 Hz;
3. VA 2 - vertical size for the image size 16:9, 50 Hz;
4. VA 3 - vertical size for size ratio 4:3, 60 Hz;
5. VA 4 - vertical size for the image size 16:9, 60 Hz;
6. VSH - vertical shift;
7. VL - Vertical linearity;
8. HSH - shift horizontally;
9. WG - White Point GREEN;
10. WR - White Point RED;
11. WB - White Point BLUE;
12. CR - RED trip level;
13. CG - GREEN trip level;
14. OSH - status symbols OSD horizontally.
Press the button until you select the desired option. For
change of the selected option press the "-", "+".
Note - The service menu, below, shows
range of adjustment options.
5.2.1 Adjustment of AGC
Apply the input signal level is 60 dBmV of RF on channel C-12.
Connect digital voltmeter to test point AGC (or at the conclusion
A tuner). Reset the parameter and select the AGC AGC voltage value in
checkpoint. Increase the setting to automatic gain control until
AGC voltage is reduced to 1 V below the aforementioned values
voltage. Make sure that the image was normal at the level of
signal at 90 dBmV.
5.2.2 Adjusting the size of the horizontal
There are four parameters control: two to 50 Hz and 60 Hz for two.
Apply the input test pattern PAL B / G for the HF. Resize
vertically as long as horizontal black line at the top and
lower parts of the test pattern will not be very close to the top and
the lower horizontal side tube, and practically disappear.
Check out and do the same adjustments, if necessary after
some other geometric adjustments.
5.2.3 Adjustment of offset vertically and horizontally
Apply the input test pattern for geometric
adjustments to the RF. Change the vertical offset as long as
test table does not align vertically and horizontally.
Check out and do the same adjustments, if necessary after
some other geometric adjustments.
5.2.4 Adjustment of vertical linearity
Apply the input test pattern mesh on the field HF.
Varies linearly in the vertical as long as the size of the squares
upper and lower parts of the test pattern becomes equal to the square of
vertically in the center of the test pattern. Check out and do that
the same adjustments, if necessary after some other
geometrical adjustments.
5.2.5 White Balance Adjustment
Apply for entry "white box" on HF. Clear all three options (WR,
WG, WB). Sets the balance (WR, WG, WB) up until
do not get a pure white screen. (For proper settings, use
color analyzer).
5.2.6 Adjusting the black balance
Reset the parameters of the CR and CG. In order to implement this
adjustment, set the specific values ​​of these parameters.
5.3 How to use byte mode OPTION (OPTIONS)
Enter the service menu. Drag strip on the choice of
OPTION line buttons. Select mode OPTION
using the "-", "+". Select the desired option. For
settings, use the number buttons on the remote control. Buttons from 0 to 7
used to change bits from 0 to 7, respectively.
Note - The service menu, below, shows
value of each bit.
The value of Brightness / Contrast OSD position and performance characteristics of
Horizontal: TTX to control the brightness, four bits of
OPTION 3 bytes. The table shows only the relevant bit
values ​​of brightness / contrast. To control the position of OSD
horizontally (the position of the teletext and menu) is used 14th parameter
menu ADJUST. variation range from 1 to 127. Increasing the value of this
parameter shifts the OSD from left to right. This adjustment should
performed in the mode of the service menu:
SERVICE
ADJUST .......
5.4 Adjustment APCHG
5.4.1 For television, not including the standard L / L '
Switch to the required standard. Apply signal
intermediate frequency (IF) at the entrance drive in accordance with the standards
(38.9 MHz for B / G and D / K, 39,5 MHz for the I) to terminals 1 and 2, the SAW filter
(Z101). Adjust the coil circuit VL101 until 2.5 V DC
voltage on pin 9 of the microcontroller (IC501).
5.4.2 For television, including the standard L / L '
Switch to the required standard. Apply signal
intermediate frequency (IF) at the entrance drive in accordance with the standards
(38.9 MHz for B / G and D / K, 39,5 MHz for the I) to terminals 1 and 2, the SAW filter
(Z101). Adjust the coil circuit VL101 until 2.5 V DC
voltage on pin 9 of the microcontroller (IC501).
Switch to the Standard L. Apply a signal of intermediate
frequency (IF) to the input of the drive in accordance with the standards (33.9 MHz for the L) on
pins 1 and 2, the SAW filter (Z101). Adjust the coil circuit to VL101
receiving 2.5 VDC on pin 9 of the microcontroller
(IC501).




* * *

الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس مود - HORIZONT   الأربعاء يوليو 20, 2011 6:46 am

HORIZONT 11AK41


When you replace the ICs and semiconductor devices, be aware that according to specifications for these devices in the sections
operating and application of the allowable value of the potential staticelectricity is not more than 200V.
In real terms the value of the potential is much higher and varies widely, if not
take appropriate measures for its reduction.
4.2 Checking circuits
Check chip is reduced to the measurement of constant and pulse voltage on their findings and
good condition attached to them elements of the scheme.
When checking pulse and constant voltage at IC to remember that count
conclusions from the existing labeling is the key to the case. On the part of print circuit boards and modules, tapes start
reference the findings of IC is marked with number 1 (counting from the clockwise direction).
If the above checks do not bring any positive results, the most effective method
check the functioning of sub-modules and modules is their temporary replacement for other, known good.
Not be allowed to inspect IC with an ohmmeter. Since IMS is the most
expensive piece should carefully decide whether to replace it.
Not allowed any replacement resistors in the food chain IC, as this may be their modeto go beyond tolerance.
5 ADJUST TVS
All system and geometrical adjustments, as well as white balance adjustment performed in
service mode, make sure that all the manual adjustments are made correctly. To start the adjustment
service mode, go to the main menu and enter code 1675 using the number keys on your remote control. On
You will see a list of groups the service mode. Groups service mode adjustments will be identified
different colors, so to enter the service mode adjustment group, click the appropriate
colors on the remote control. After selecting the adjustments you can select menu items that
mode using the remote control buttons, the cursor up and down. You can choose any value
item using the remote control to move the cursor left and right.
To switch to another group of adjustments, press the colored button in the group. For
save the settings, click «OK SELECT». To exit this menu, press servicebutton «MENU».
5.1 Use of color remote control buttons
The red button is used to adjust the geometry of horizontal and vertical.
The green button is used to enter the video adjustments.
Yellow is used to enter a submenu choice of systems.
The blue button is used for service adjustments.
5.2 Geometric adjustment of horizontal and vertical
Switch the program to a universal testing table. Press the red button on the
remote control for this group of regulations. Select a specific regulation with the buttons
?,? on the remote. After selecting a particular control, configure it using the buttons?,? on the remote.
To save your settings, click «OK SELECT» remote control. To exit this menu, press
button «MENU».
5.2.1 Vertical Shift
Press?,? To put a test table vertically at the center, ie
horizontal line in the center of the test pattern should be the same distance from
the top and bottom of the tube. Check and reconfigure the regulation of V-SHIFT, when adjustment wasinappropriate once committed other geometric adjustments.
5.2.2 Vertical Size
Press?,? To the horizontal black lines on top and bottom
test pattern is very close to the top and bottom sides of the picture tube. Check and
reconfigure adjust V-SIZE, if adjustment was inappropriate after the other committed
geometric adjustment.
5.2.3 Horizontal Shift
Adjust the H-SHIFT with the buttons?,? To the test table is available on
same distance from the left and right side tube. Check and reconfigure the regulation of H-SHIFT,
If the adjustment was inappropriate after the committed other geometric adjustments.
5.2.4 Horizontal Size
Adjust the H-SIZE with the buttons?,? That were not visible white rectangles on the left and
the right side of the test pattern or image is not wide. Check and reconfigure the
adjust H-SIZE, if adjustment was inappropriate after the committed other geometricadjustment.

32
5.2.5 volvulus
Press?,? To the size of the squares on the top and bottom of the test pattern
was equal to the size of the squares that lie on the vertical center of the test pattern. Check and
reconfigure the adjustment S-COR, if adjustment was inappropriate after the other committed
geometric adjustment.
5.2.6 Linearity
Press?,? To the size of the squares of the test pattern were equal across the screen.
Check and reconfigure the adjustment LINRT, when adjustment was inappropriate after
committed other geometric adjustments.
5.2.7 Rotation angle view
Press?,? To the test table was completely perpendicular
horizontal lines without vertical displacement angle. Check and reconfigure the adjustment ANGLE,
If the adjustment was inappropriate after the committed other geometric adjustments.
5.2.8 Bending
Press?,? To vertical lines, especially those that are close to the left andright sides, will level off and become a bandage symmetrical, ie together they will not be directed or
to the left or the right side. Check and reconfigure the adjustment BOW, when adjustment was
inappropriate once committed other geometric adjustments.
Trapeze 5.2.9
Press?,? To vertical lines, especially lines that are located on the edge
images are parallel to both sides of the tube. Check and reconfigure the adjustment TRPEZ,
If the adjustment was inappropriate after the committed other geometric adjustments.
05/02/10 Parabola
Press?,? To vertical lines, located close to the edges of the image, began to
parallel to the vertical sides of the picture tube without bending to the left or right side of the screen. Check and
reconfigure the adjustment PARAB, when adjustment was inappropriate after the other committed
geometric adjustment.
05/02/11 The upper corners
Press?,? To vertical lines, located in the upper corners of the pictureare vertical and parallel vertical sides of the picture tube angle. Check and reconfigure the
adjustment U. COR, if adjustment was inappropriate after the committed other geometric
adjustment.
05/02/12 Lower corners
Press?,? the vertical lines are located in the lower corners of the picture
are vertical and parallel vertical sides of the picture tube angle. Check and reconfigure the
adjustment L. COR, if adjustment was inappropriate after the committed other geometric
adjustment.
5.3 Adjusting video
Switch to the program with the test pattern for geometric adjustments to the program
color bars for the video adjustments. Press the green button to enter this group. Choose items with
buttons?,?, After selecting the control, configure it using the buttons?,?. To save
installations, press «OK SELECT». Switch to another group using the colored buttons. To exit
this menu, press the «MENU».
5.3.1 White Balance AdjustmentApply test signal "white box" on the antenna input. Change all of the analog control
on average, and set RGn, GGn, BGn 80, if necessary. Use the analyzer to the color
Color Temperature Control (X, Y). Select RGn BGn and with the buttons?,?. Use?,?
change the values: X = 285 +10, Y = 293 on the analyzer 10 in color. Set the value adjustments
PRf, GRf, BRf 62 (permanent).
5.3.2 Luminance Delay field
Apply test signal "streak." Select YDF with buttons
?,?. Adjust the YDF with the buttons?,? To varying colors on the color field became clearer and
mixed with each other. Check and reconfigure the adjustment YDF, when adjustment was
inappropriate after the other adjustments are committed YD F. Factory settings will
figures: YDFP (for PAL): 01; YDFS (for SEKAM): -07; YDFN (for NTSC): 01.

33
5.3.3 Automatic Gain Control
Apply signal PAL BG, VHF-channel 3-12 with the signal level at antenna input 60dBmV. Adjust the AGC
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس مود - HORIZONT   الأربعاء يوليو 20, 2011 6:49 am

that the voltage at AGC (pin 1 tuner) on the digital voltmeter was 3.0 V. factory setting in
Technology menu will AGC: 034.
5.3.4 Automatic program search
The value of this control is switched between ON (ON) and OFF (Off) buttons?,? after selection
control buttons?,?. To activate the setting procedure APS whenever include TV, in
first select switch on the TV without ON.Chtoby activation procedure to establish APS select OFF.
5.3.5 Tuner (TLANE)
T_T adjustment is used to select the tuner. SAM, THO, SIE, ALP, MK2, MK3 for Samsung,
Thomson, Siemens, Alps and Philips MP2/MP3 /. The factory setting is T_T: TNO.
T_R adjustment is used to select the tuner. SAM, THO, TEM, MK2 for Samsung, Thomson, Temic,
Philips. The factory setting is T = P: TNO.
5.3.6 EHT3
This control is switched between ON (ON) and OFF (off) and used to enable and
Off EXT3.
5.3.7 Color menu CLT (C.M. - Color Menu)
This adjustment is used to set the menu colors. There are 5 options. Factory setting
SM: OFF.
5.4. Service Adjustment
WARNING! Adjustment in service mode are not possible at the time, when carried out in control
operation.
Press the blue button on the remote control when operating mode is activated. Click a color button
adjustments of the group. Click?,? to select the adjustment. Click?,? for
select a value adjustment. Click «OK SELECT» to save the settings and click «MENU» for
out of service mode.
5.4.1 Group adjustments
Press the red button on the remote control to enter into this group of adjustments:
PIP CNTRST - level images PIP (000);
PIP Y Delay - delay image brightness PIP (000);
PIP Frame - frame color choice PIP (edge ​​PIP) (0);
EHTHP - compensation factor for the horizontal phase of the EH T (stress the 2nd
anode) (001);
EHTHTS - time constant to compensate for the horizontal phase of the EH T (000);
EHTH - compensation factor for the size of the horizontal EH T (-14);
EHTV - compensation factor for the size of the vertical EH T (-14);
EHTV TS - time constant for controlling the size of compensation in the vertical and
Horizontal (005);
INIT NVM - the initiation of non-volatile reprogrammable memory (NVM).
SV DEL delayed images SEKAM (008)
OSD CONT - Contrast OSD (070);
OSD BRI - the brightness of the OSD (035);
TEXT BRI - teletext brightness (030);
PIP Y DelSe - luminance delay image RIR SEKAM (000)
5.4.2 Group options
Press the blue button on the remote control to enter into the group options:
0 HPHONE - ON / OFF (earphone) (ON)
A CRT - 4:3 / 16:9 (CRT) (4:3)
2 S-VHS - ON / OFF (connector S-VHS) (ON)
3 f (IF) - always set to 38.9
4 Turk - Turkish menu ON / OFF (OFF)
5 VGA - ON / OFF (ON)
6 FRONT - Front AV ON / OFF (RCA connectors on the front of the TV) (ON)
7 DPL - ON
8 VD - ON
9 NSL - ON
10 PAP - ON

34
5.4.3 Group selection options systems
Press the yellow button on the remote control to enter into the group options:
0 PAL B / G - ON / OFF (ON)
1 PAL D / K - ON / OFF (ON)
2 PAL I - ON / OFF (OFF)
3 SECAM B / G - ON / OFF (ON)
4 SECAM D / K - ON / OFF (ON)
5 SECAM L / L - ON / OFF (OFF)6 AUST - ON / OFF (OFF)
5.4.4 With the options set the sound processor
Press the green button on the remote remote control to enter the group of options:
FM: 015
NICAM: 035
I2S: 016
SCART: 025
5.4.5 The group of options and settings tube ERM
Press the green button on the remote remote control to enter the group of options:
BCLTHR (mA): 1.8 mA-ray tube current limit.
The remaining options in this submenu to change.
5.5 Adjustment APCHG
Give the drive signal "color bars" frequency of 38.9 MHz PAL B / G (90dbmV) to the inputs 1 and 2, SAW filter
(Z403). Connect digital voltmeter to the point APCHG (pin 22 of IC 401). Adjust the coil
VL401 so as to obtain voltage (2,5 ± 0,1) V on pin 22 IC 401. In this case the TV should
automatically tune to the station with automatic search.
5.6 Adjusting the Focus
Turn on the TV in the operating mode and tune to signal "streak." Adjust
potentiometer focus (back of upper TDKS potentiometer) at optimum focus
image.
5.7 Adjust the accelerating voltageSubmit a modulated RF signal "streak» PAL B / G to the antenna input. Measure at
with an oscilloscope probe 1:100 voltage R, G, B cathode tube video amplifier module
tube.
Attention! Earthen output probe oscilloscope must be connected to pin 1 (ground) module
video amplifier tube.
Adjust all the functional adjustment (brightness, saturation, contrast) to the minimum
position. Select the most sensitive cathode tube. Adjust the potentiometer accelerating
voltage (lower potentiometer on the back of TDKS) on this cathode tube voltage suppression
150V.



* * *

الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس مود - HORIZONT   الأربعاء يوليو 20, 2011 6:53 am

HORIZONT 12.7


1 ELECTRICAL ADJUSTMENTS
1.1 Adjusting the voltage
Connect digital voltmeter to the cathode of diode D607, set the AV mode and set
accelerating voltage for accelerating the minimum potentiometer TDKS. Adjust the tension
supply (+ V) potentiometer R607 to the following:
14 "(37cm): 105VDC (for A33EKS01h01)
20 "(51cm): 118VDC (for A48EJW011x21)21 "(54cm): 110VDC (for A51EFS83x191)
2 SERVICE ADJUSTMENTS
To enter the service mode, press «Service In / Out» remote process
Control or set the image menu using the remote control that came with the television and dial
the number buttons of the remote 9301.
To exit the service mode, press 0.
Red, green, yellow and blue buttons are used to set properties, geometry,
The white balance menu, and drive accordingly.
2.1 Adjustment of the drive
2.1.1 PAL SECAM BG / DK / I
• Connect an RF signal modulated 471.25MGts colored stripes in the BG with
test generator on the TV and locate the TV signal using
"Setup" menu (C21).
• To deactivate the circuit (loop) APCHG, move (or change) the value of "accurate
Settings "from the center point on a single value (one) and then return back to the central
point (2 small vertical lines are shown on the scale at a central point). Remember channel
line KEEP selecting and clicking "OK".• Enter the service menu and press the blue button on the remote control.
• Check the «PVC38», it should be 07. Adjust the coil LC101 so
so you can see the value "OK".
• Click "OK" remote control.
• Exit the service menu.
Note - «PVF38» is designed for fine-tuning. Nevertheless, it automatically
adjusted when the button "OK" is pressed when selecting «PVC38». Thus, no manual
adjustment is required.
2.1.2 SECAM L / L '
• They require no adjustment. «PVC33» and «PVF33» will be reserved SECAM L / L '.
2.2 Torque adjuster AGC
• Apply a signal with an amplitude of 65 ± 1 dBmV to the antenna input on your TV by TV
test generator (carrier sound OFF and ON «Video Ext»).
• Enter the service menu and press the red button on the remote control.
• Use the "P +" / "F" Find AGC.
• Measure the amplitude of an oscilloscope with a sine wave output at 38.9 MHz, 11
(IF2) tuner.
• Change the automatic gain control to a value of 640 ± 20 mVpp.
• Add 5 to the value of the AGC (AGC) and change «2.AGC» to this value.• Exit the service menu.
2.3 Adjust the accelerating voltage
• Enter the service menu and press the yellow button on the remote control.
• Select the menu «SCRN». Apply signal "color bars" on the input of the TV.
• Adjusting the picture tube for 14 "(37cm): Adjust the accelerating voltage potentiometer
on the applied voltage TDKS concluded resistor R727 (which is connected to the cathode
tube) with respect to ground equal to 139 ± 3VDC.
• Adjusting the picture tubes for 20-21 "(51-54cm): Adjust the potentiometer accelerating
voltage on the voltage applied to the TDKS conclusion resistor R727 (which is connected to
cathode tube) with respect to ground is 164 ± 3VDC. (For CRT 20 "Ekranas firm value
adjustment should be 154 ± 3VDC).
• Exit the service menu.
3
2.4 Adjusting the white balance
• Apply signal "white box" from a television test generator to the antenna input
TV.
• Enter the service menu and press the yellow button on the remote control.
• Press the "P +" / "P", select «B. DRV» «+»/«-» and buttons, change its value to 32.• Adjust the «R. DRV» and «G. DRV» to get the white balance.
• Adjust the «R. CUT» and «G. CUT» for blocking thresholds of red and green light
(Threshold level locking is not blue beam).
• If white balance is not obtained, change the value again «B. DRV».
• Exit the service menu.
2.5 Geometric Adjustment
• Connect the antenna input of the TV signal from a television test generator
a test pattern (UEIT).
• Enter the service menu and press the green button on the remote control.
• Adjust the vertical size with the option «V.4: 3".
• Add 18 to the received value of this option and change the «V.16: 9" to this value.
• Adjust the vertical alignment with the option «V. POS», the linearity of the vertical at
with the option «LNRTY», horizontal alignment with the option «H. POS».
• Subtract 14 from the value of options «V.4: 3" and change the «V1.60» to this value.
• Add 4 to the value of options «V.4: 3" and change the «V2.60» to this value.
• Set the option «VP.60» the same meaning as in the option «V. POS».• Set the option «LN.60» the same meaning as in the option «LNRTY».
• OSD position on the screen may vary with options «OSD.H» and «OSD.V».
• Exit the service menu.
Note - This chassis is not a size adjustment in the horizontal. It can be
adjusted by changing the supply voltage (+ V) in the range of +1 V and-1V.
2.6 Installation characteristics
Enter the service menu using the remote control technology first and then the red,
then blue button. Change the characteristics listed below with the above settings.
TUNER: Philips, Sharp & Alps, Panasonic, Temic
ST.BY: YES (the default is automatically activated)
NO (can be used for repairs)
AV2: YES (have RCA jacks on the front panel), NO
CLR.S: PAL, PAL/NTSC3, 5 (+ NTSC playback), PAL / SECAM, PAL/SECAM/NTSC3, 5 (NTSC
playback)
SND.S: BG, I, BG + DK, BG + LL '
QSS / I: INTERCARRIER, QSS
TEXT: NON TEXT, DEFAULT (Teletext), FASTTEXT
LANG: A (West Europe - Western Europe), B (East Europe - Eastern Europe)HOTEL: NORMAL TV, HOTEL TV
RGBIN: YES (when there are inputs for RGB SCART, antenna input is displayed for
Some hotel TV)
APR: ON (automatic control of RGB levels available) (ON)
OFF (OFF)
B. STR: ON (ON) (black level control is available)
OFF (OFF)
ATS: YES (automatic configuration is enabled), NO
Note - ATS should be set to NO in the TV without
Teletext. For TV mode HOTEL ATS can not be established in
position YES
AVL: YES (automatic limitation of the volume of sound (advertising) is included), NO
ZPG: YES (function programmable timer switch channels included), NO
ZAPP: YES (switching function of channels with one button is enabled), NO
4
2.7 Mode HOTEL
If the option HOTEL in the service menu is selected as the HOTEL TV, the entrance to the setup menu
given the numbers 4, 6, 5, 8, when you choose CHARACTERISTICS. Installation Option menu
HOTEL TV selection includes the following elements:
HOTEL MODE: ON / OFF (ON / OFF) search (selection) and ending search for TV channels (starting with 00)(Mode HOTEL)
RADIO MODE: ON / OFF (ON / OFF) search and start search for radio channels (ends 99)
(Radio mode)
MAX VOLUME: maximum allowable volume
(Maximum volume)
RESET ADJ: size presets sound and images that are obtained after
installation (recovery operations (adjustments)
adjustments)
MESSAGE: desired message can be edited (max. 148 characters)
(Message)
INFO SCREEN: informational message can be edited (3 pages, each of length
500 characters). The user receives these pages by pressing the «INFO» remote control.
LOAG DATA: not working
(Date of download)
SAVE DATA: not working
2.9 Exit service mode
When you exit the service menu of the software version and optional features
(Hexadecimal number) are displayed on the screen. For example: SC1.120-01 66F3 T03030702.



* * *

الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس مود - HORIZONT   الأربعاء يوليو 20, 2011 6:54 am

HORIZONT 51CTV-676T-I-10-676T SHTST.


Dej regime of press on the remote control
DISPL ---- MENU ---- MUTE ---- POWER ON
Exit button TV.
You can remote control RC-5SERV is part of a universal remote MAK 2002 maxi,
код 1255 SHIFT и P +
SHIFT и P -


* * *

HORIZONT 54CTV-730-I-9


Вход в SERV
Dej regime of press on the remote control
DISPL----MENU----MUTE----POWER ON
Exit button TV, a return to the menu button AV. You can remote control RC-5



* * *

HORIZONT 63CTV698T-I-31 chassis 14.2


SERVICE: RC-5 (buttun "Contrast -)
TUN. - Philips
TEXTON/OFF - TEXT
EWP1 - 08
TEST - 30
CRT - 4:3
HOTEL - OFF
HBOW - 32
HPAR - 32
IF0F - 32
PWLT - 11
TXT TABLE CYRI
FASTEXT YES
SSTD ALL SYS.
VZOM - 36
RGB - 01
SAWF - 01
VSLP - 31
VSHT - 23
SCORE - 25
VAMP - 42
EWW - 61
HSHT - 29
EWPW - 12
EWCL - 17
EWCU - 18
EWT - 32
BRI - 32
CDR - 05
CON - 40
HUE - 32
SAT - 31
YDLY - 04
Blore - 36
BLOG - 30
BLUE - 34
RED - 40
GRN - 32 !
SCRN OFF
PEAK - 33
EEPE 00
STD. STD-BY - ON
AGC - 35
SC3325-D04 VER
6F85
T02020619



* * *
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس مود - HORIZONT   الأربعاء يوليو 20, 2011 7:00 am

HORIZONT 70 CTV-694T-I-16


login SERV 4 7 2 5


* * *
[b]HORIZON 54CTV-730-I-9 processor TDA9381PS/N2/1I0840[/b]

Of Dej regime to press for PDUON)

(DISPL)(MENU)(MUTE)(POWER


Exit button TV, a return to the menu button AV. (Action can be made remote control RC-5)
HORIZON 63/70STV-698 processor TDA9555H
On the remote control RC-5 with twin adjustable image. The "Contrast" - entry into service
mode.

* * *

HORIZON 72DTV-694DTI-18


Turn on the television to normal operation, to then click the "Network" on the front panel
TV (LED will turn red), then press the channel change "P +"
or "Ch +" in front of the TV or remote (the LED turns green).
Put the DVD-TV switch on the remote to TV. After the image appears
Press "Menu" button on the remote control (Table menu will appear), while in
menu, press the button consecutively 1,6,7,5 - service menu will appear in the form of tables with color
headings. Moving between tables may be using the buttons on the remote marked
colored dots (pixel color matches the color of the table title). To save the results
settings, press the "OK" button.HORIZON 670/676/690/730


Processors SAA55XX, TDA93XX, R83S055
For the manufacture of the remote service to take RC7-2 or any other on the m / c PCA8521BT/040.
To conclusions 3 and 11 to connect an additional button "SERVICE"


* * *

HORIZONT 54CTV-678-I-30


SERV is part of a universal remote MAK 2002 maxi, code 1255, counter, counter +
toggle menu items.
TUNER: PHILIPS
AGC: 32
2 AGC: 37
ST.BY: YEC
AV2: NO
CLR.S: PAL/SECAM/NTSC3.5
SND.S: BG + DK
QSS / I: INTERCARRIER
TEXT: NON TEXT
LANG: B
HOTEL: NORMAL TV
RGBIN: YES
APR: ON
B. STR: OFF
Button H / V
H. POS: 39
V. POS: 6
V.4: 3: 50
V.16: 9: 63
LNRTY: 50
VP.60: 11
V1.60: 18
V2.60: 36
LIN.60: 50
OSD.H: 31
OSD.V: 39
button M / S
R. DRV: 33
G. DRV: 32
B. DRV: 32
R. CUT: 32
G. CUT: 32
SCRN: 0


* * *


الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس مود - HORIZONT   الأربعاء يوليو 20, 2011 7:02 am

STV 660.661


Turn on the TV button "Network" in pre-closed contacts of the control
XN10 point on SHTST. After warming the kinescope click the "Menu" (SL)
Installing the required option byte keys "P +", "P" and the "+" "-".Exit the service mode button "TV" set value is stored
automatically.



* * *

HORIZONT CTV-664

.
5 ADJUST TVS
To enable the adjustment, press the blue button remote control, with
on the TV SETUP menu should appear.
Click the button consecutively 4,7.2 and 5 remote control. This will display the Tools menu
the following:
SERVICE
ADJUSTMENT
A. .. OPTIONS ...
5.1 Manually tuning the chassis
To choose your options, press "P +" or "P" remote control to change
selections using the buttons "+" or "-".
The parameters of the service menu chassis AK30 below. For some parameters
given default.


5.2 Use of color remote control buttons in the service menu
The red button (only for stereo models): Shifts in the AVL ON or OFF modes in
service menu. In the service menu shows the word AVL, AVL mode when ON,
Green button toggles the aspect ratio of 4:3 or 16:9 in the service menu.
Especially necessary when setting up the vertical dimension of the picture mode to 16:9.Yellow button switches to the mode vertical scan disable. Used when setting
accelerating voltage.
The blue button is used to automatically adjust the AGC and IF in the service menu.
5.3 Managing white balance
The next three parameters are used to adjust the white balance. For this
Use tsvetoanalizator. Using the parameters of WR (setting the white point for
red), WG (setting the white point for the green), WB (white point adjustment for
blue), put a + sign in the square in the middle of the screen.
Suggested values ​​for these parameters are shown in the table above.
5.4 Configuring the AGC
In order to adjust the AGC, apply an RF signal level of 60 dBmV Channel C-12
(224.25 MHz). Select the service menu, the ARU. Press the blue button on the
Remote control. Will be configured
automatically by software. Check the AGC on the service. Menu
should be 1.
Check the image quality when the normalized signal 90 dBmV.
5.5 The negative adjustment drive (No L ')
Set the table test in the form of PAL color bars with a frequency of 38.9 MHz. ApplyIF signal to terminals 10 and 11 of the tuner. Press PROG-1, and then the blue button on the remote.
Select the standard BG or I,
(BG if possible). Enter the service menu. Select a service from IF1
menu and press the blue button on the remote. Setting up the drive is automatically
software. Check the drive on the service menu, it should be
Figure 12.
5.6 The positive adjustment drive (with system L ')
Set the test table SECAM as bands with a frequency of 33.9 MHz.
Apply the IF signal to terminals 10 and 11 of the tuner. Press PROG-1, and then the blue button
on the remote. Select BAND VHF-1 and the standard L '. Enter the service menu. Select
IF1 from the service menu and press the blue button on the remote. Setting up the drive by
automatically by software.
5.7 Setting the horizontal position of OSD
Select the OSD in the service menu. Adjust the horizontal position of OSD in
middle of the screen with a support band at the bottom of the service menu.
5.8 Adjusting the brightness of the teletextSet your TV to a channel with teletext. Enter the service menu. Press
on the remote. Adjust the brightness value of 39 buttons "+" or "-" Remote
Control. Press TV and the SL on the remote. Setup completed.
5.9 Optional Installation
Select an option in the service menu. To change a bit in the option selected, you must
press the same digit on the remote. Since this bit can be changed from 1 to 0, and 0 to 1. If
any option chosen in the service menu, then on the TV screen shows the number of
numbers of bits.
Note - In case of failure do not need the original EEPROM EEPROM for
to run the TV. Because of the special characteristics of software, chassis, AK-30 works with
non-programmable EEPROM (without EEPROM). In the case of utility hook installation
must be fulfilled in the new EEPROM of the same type when installing it on the chassis and
adjust all the options perform in accordance with the procedures specified in the above
Repair Manual.


* * *
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس مود - HORIZONT   الأربعاء يوليو 20, 2011 7:04 am

CTV678/698

.
On the remote control technology (RC6-7-5T) click "-/--".
Exit the service mode button "TV". In order to remember the values ​​of all adjustments
necessary after the exit from the "Tools" put the television into standby mode.


Managing bow
Plan to release a TV with IC R83S055 with Russian menu.
In the TV series CTV-690. CTV-705 has a control byte code is
defines some properties of the TV (the number of external connectors, AV1, AV2,
AVS), and for televisions with a Russian menu - CRT format 4:3 or 16:9).
Codes of the control byte, depending on the language menu and format of the picture tube are shown Table 1.
Table 1
Language Format CRT code manager
An English 4:3: 16: 9 Months
Russian 4:3 3C (2D)
Russian 16: 9 38
2
To test the code of the control byte must be translated into TV mode "SERVICE"
by clicking on SB1 monoshassi and keep it pressed until the
message "PW" or "Parabola." By pressing the remote control "DISPLAY" cause
control byte. On the TV screen should show a label for the menu with an English orRussian:
CTV 530 S V 1.04
OP FOR
For the menu, with the Russian language and format of the picture tube "4:3":
TSTV530R Q1.10
NRM. BYTES AP
If the code of the control byte does not correspond to the table, with the help of the book. ("+","-") Control
Control necessary to establish the desired value of the control byte code,
To remove a control byte from the TV screen, click the button control "TV" ..
3 Procedure for entering the mode "Servise" to adjust the parameters
To enter the "Servise" press and hold the button on the SB1 in monoshassi
pressed until you see the "PW" or "Parabola." Followers,
lnym pressing "V" remote control to select the option to control
All parameters, except APCHG may be regulated by the "+", "-" remote control, as
specified in the relevant section repair manual. To exit
"Servise" must click "TV" remote control.


* * *
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس مود - HORIZONT   الأربعاء يوليو 20, 2011 7:06 am

Horizont 37/51/54 CTV-730


control color TV "Horizont 37/51/54 CTV-730."
Adjusting the TV in service modeTranslations TV service mode as follows:
• press the "AV" on the front of the TV and hold the button include
"Network". On the TV screen should display: CTSMONZAIF38.AFC3:
• RCU for RC6-7, which is shown in Fig. 1, V-VII buttons select the desired adjustment for
optional byte;
• The "+" or "-" in front of the TV set the necessary values ​​for
This option bytes;
• To exit the service mode, press the button on the remote control IV.
After replacing the memory chips on the new DA101, which are not recorded data, it is necessary
written preliminary data and establish optional bytes.
Table 7. Byte BITS
To order the firmware memory chips discussed below.
Optional bytes - this eight-memory registers
Products DA101, in which functional data are recorded.
In the type of memory chip DA101 M24C08WBN6 of seven bytes
(OP1-OP6, BITS). Table. 1.7 shows the recommended values
option bytes.
We now consider the procedure to record the preliminary datain the memory chip DA101.
To do this, perform the following operations:
• translate TV service mode;
• to briefly press the remote control II; • the remote control
briefly press the V or VII, after a
time on-screen message should appear: INIT CTV
UOCEV1.4.
This means that the TV is ready to adjust the parameters.
4
Figure 1.
Press V and VII on the remote produce a recording check data memory chips DA101.
Parameter changes produce IX and X buttons on the remote.
The parameters and their values ​​are recorded in the chip DA101, are given in Table. 8.
When an erroneous setting of a parameter appears READY.
Unlock (Feature "The Castle") without knowing the key code is as follows:
• pressing VIII (blue), remote part of the menu functions of the first cycle (refer to
TV), and, holding the IV in 2-3 with include OSD);
• buttons V and VII of the remote cursor will transfer into the "Castle";
• button remote III removed the menu background;
• Hold for a few seconds, I click the remote, then on the screen in the "Castle"the word "On" should be changed to the word "off".
This means that the lock is removed.


* * *

الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس مود - HORIZONT   الأربعاء يوليو 20, 2011 7:09 am

DTV700, 710


On the user's remote control:

  • adjustment "Volume" set to "0"
  • press the mute button ()
  • press the timer button ()

Adjustments in the "Service" radio button "P +", "P" on the ring.
The value of the setting, change the buttons "+" "-"
Remembering the values ​​of adjustment is done separately for each of them by pressing
the green button on the remote control


* * *

STV670


When TV is turned off on the front panel or remote control press "AV" and
hold down the button turn on the TV "Network". Click "AV" to hold to
appearance of the raster. You should see a message IF38, 0AFC3, that
indicates switch on "Tools." In the absence of the screen
smooth rotation of the adjustment of "accelerating" in TDKS upward to achieve
appearance of the emission pattern on the screen.
Installing the required optsionnnogo byte keys "P +", "P" and the "+" "-".Exit the service mode button "TV" set value is stored
automatically.



* * *

CTV676


1. Close pins 1 and 2, the reference point for SHTST XN11-676.
2. While in standby mode on the user's remote control to click consistently:
"Status" (), "SL", "Off. Sound" () "standby mode" ()
To save the results in the "Set Up TV" press ""
Return to the previous menu button "TV



* * *

METHOD OF SETTING CHASSIS SHTST-678


1. Service mode
To enter and exit the operating menu you need a special TV remote
remote control (you can buy it from the manufacturer.) All buttons service
remote control are the same as on the user's remote control button is only added «IN / OUT».
Sign in PICTURE menu by pressing the «SL» remote control. Press the number
button
7, 5, 9, 2 remote control. You will see the service menu. To exit the service
mode, press the 0 button remote control.
1.1 Adjustment of the power supply voltage
Connect digital voltmeter to the cathode of diode D610 in AV1 mode and setminimum accelerating voltage (SCREEN). Set up the main supply voltage + B
Potentiometer R601 on the following:
14-inch 106V A33LPE02X01 Fri
20-inch 118 A48ECR14X51 Fri
21 inch 118 A51EFS133X41 Fri
Adjust the potentiometer of the accelerating voltage so that the image on
screen was visible.
1.2 Adjustment of the drive
Before adjusting the drive go into service mode, change the title «VIDEO» on
«NEW». Exit the service mode.
WARNING! The above actions are carried out ALWAYS
AFTER REPLACING CHIPS OR MEMORY CHIPS 1S101 EEPROM.
IF ADJUSTMENT SHOULD ALWAYS AFTER REPLACING OSUSCHESTVLYAYUTSYA
TITLE «VIDEO» ON «NEW».
Standards for BG, DK, I set the oscillator frequency images (tranzitesta) on
38.9 MHz and set it on the color bars. Connect the RF generator output
images found 1F101. Sign in service mode. Make the setting item
«AFT38» service menu so that the derivation was 23 1S101 value
voltage 1.45 V ± 100 mV DC. Exit the service mode.1.3 Adjustment of AGC
Apply a signal in the channel 32 with a level of 60 ± 1dBmV to the antenna input (no sound carrier and
enabled «Video Ext»). Connect the oscilloscope to the conclusion that 11 (1F2) and the tuner to the ground.
Enter the service mode and find the heading "AGC". Adjust the amplitude on
values ​​listed below, which are visible on the oscilloscope using the buttons "+" ("-")
Remote Control:
5.12 for standard chassis BG, DK, I: 630mVpp ± 20mVpp;
Chassis for 5.12 standarta LL: 450mVpp ± 20mVpp;
5.12 for standard chassis BG, DK: 630mVpp ± 20mVpp;
Chassis for 5.12 standarta LL: 450mVpp ± 20mVpp;
Chassis for 5.12 standarta I: 500mVpp ± 20mVpp;
1.4 Adjusting the tuner
Install the service mode. Select the title «TUNER».
TUNER SHARP & ALPS
PHILIPS
P. SONIC
TEMIC
Broadband
UHF only
Items "Broadband" and "UHF Only" apply only to the chassis 12.4.
AV2 NO: a SCART
YES: a SCART + Connectors AV (RCA) on the front panel
CLR.S PAL
PAL / NTSC: SECAM is detected automatically
SND.S BG
I
BG + DK
TEXT DEFAUIT: Teletext
FASTEXT: Fastext
1.5 Geometric ConfigurationSign in service mode. «H. POS» for horizontal position. «V. HEI» for
the vertical dimension. «LNRTY» for linearity with respect to the vertical. «S. COR» settings for S-
correction.
1.6 Adjust the accelerating voltage
Sign in service mode. Select the row SCRN. Click the "+" ("-")
remote control. At the bottom of the screen appears white horizontal line. Adjust the accelerating
potentiometer level horizontal line so that it was only slightly
visible.
1.7 Setting the white balance
Sign in service mode. Select and set «G. CUT» 128. Customize
«R. CUT» and «B. CUT» to end the setting. Select and set «R. DRV» and «B. DRV»
for white balance. Exit the service menu.
1.8 Pre-installation service menu value items
The values ​​below are averages and can vary
Depending on the type of picture tube and chassis.


2. Adjusting the data rays
Note-Before adjusting the TV information should be included at least
15 minutes.
2.1 Adjustment of the information in the center of the screen1. Apply a test table in the form of a mesh generator with a field test
signals.
2. Adjust the brightness and contrast to get good pictures.
3. Adjust the two tabs four-pole magnet to change the angle between them,
Align the red and blue vertical lines in the center of the screen.
4. Turn both tabs at the same time, keeping the red and blue lines in
center of the screen.
5. Set up two ledges and 6-pole magnets to match the red / blue and
Green Line into one. Setting angle affects the vertical lines, and the rotation of the two
magnets affect the horizontal lines.
6. Repeat setting 3, 4, 5 for better information. Settings are made with
great caution because of the mutual influence of 4-and 6-pole magnets.
2.2 Torque adjuster information on the outer edge of the screen
1. Loosen the screw that secures the deflection system (OS) for free
moving clamp.
2. Insert the temporary wedge (not pluck the paper from the adhesive side of the wedge).
3. Move the bracket up and down for better information on the outer edge of the screen.Insert a wedge between the CRT and the operating system for the temporary fixing clamp.
4. Insert a wedge from the bottom and hit him with the paper.
5. Move the clamp to the left and right for better information on the outer edge of the screen.
6. Secure the clamp position and insert another wedge on top. Tear away with it
paper and glue on the wedge for fixing the picture tube clamp.
7. Temporarily remove the wedge is inserted, and insert in another part of the above. Glue
on its picture tube to fix the clamp.
8. After fixing all the wedges check information. Tighten screw
fixing clamp, and check how well kept the clamp.
9. Stick the three tapes in the wedges.
2.3 Compensator information
Compensators and L462A L462Bispolzuyutsya correction of incomplete information
(Red-green) at the top center and bottom center of the screen. Compensator also L462S
used for correction of incomplete information (the vertical displacement of the blue or red)
in the four corners of the screen.
1. To correct for incomplete information, the horizontal (red-green), insert
compensator on the rear of the clamp to find the best position information. Markposition and detach the protective paper from the compensator L462A and stick it on the site.
Use masking tape to clamp and L462A.
2. To correct for incomplete information, the vertical (red-green), insert
L462B tips compensator in the hole collar and glue.
3. To correct for the upper and lower red shift in the upper right or
the lower right corner insert compensator L462C in point 1 or 2 for finding the tube
better position information. Mark the position and detach the protective paper from the compensator
L462C and stick it on the site.


* * *
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس مود - HORIZONT   الأربعاء يوليو 20, 2011 7:11 am

METHOD OF SETTING CHASSIS SHTST-698


1. Adjust the power supply voltage
Connect digital voltmeter to the cathode of diode D611 in AV1 mode and set
minimum accelerating voltage. Set up the main supply voltage + B
Potentiometer R601 on the following:
33 "159V 1 B;
29 "125V 1 B;
28 "145V 1 B;
Adjust the potentiometer of the accelerating voltage so that the image on
screen was visible.
2. Service mode
To enter and exit the operating menu you need a special TV remoteremote control (you can buy it from the manufacturer.) All buttons service
remote control are the same as on the user's remote control button is only added «IN / OUT».
Sends a signal to the antenna jack with level 65 dB (V ± 1 dB (V (1,8 mV)
2.1 Adjustment of AGC
AGC buttons to choose "P +", "F" remote. Configure the frequency of the signal
38.9 MHz on the output value of 2 tuners 220mVpp ± 20mVpp.
2.2 Torque adjuster STD
It should be STD-BY ON.
2.3 Adjustment of EERE
It should be set up in position 00.
2.4 Adjustment for 08 PEAR
Customize HEAD ON to 28 ".
3. Geometric Configuration
Select or FUBK PHILIPS test kit (UEIT).
Customize 3.1 VZOM 20.
Customize VSCR on 1F.
Customize AV at 03.
Customize CRT at 4:3
3.2 Press "P +", "P" to select VSLP. In this mode, the lower half of the screen
black.
Customize VSLP to the center line in the test table (UEIT). Set up in VSHT
the center line of the test table.
3.3 Adjust the vertical linearity for SCOR and vertical size for VAMP.
Adjust the horizontal size by EWB and the horizontal displacement at HSHT.Configure the general parabolic adjustment for EWPW.
Adjust the angle adjustment on the cusp EWCR.
Adjust keystone on EWT.
Configure BRI for 20 to 28 "
CDR 03
CON 28
HUE 20
SAT 14
YDLY at 04
4. White balance adjustment
Set the brightness to 30, contrast 40, color 20.
Sign in service mode. Select SCRN and turn to ON. Screen
become black in the center of the screen will display a horizontal line. With the accelerating
potentiometer (SCREN) set the line to barely visible levels.
Select a GRN and set at 25. Adjust the red (RED) and blue (BLUE) for
necessary values ​​to obtain the correct white level.
Return to the image by pressing the "+" ("-") Remote Control

* * *
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس مود - HORIZONT   الأربعاء يوليو 20, 2011 7:14 am

Horizon TV CTV660/661


To enter the service mode the following steps to perform:
jumper contacts XN10 checkpoint at monoshassi and connect the TV to work.
After that, press the MENU button and the screen service menu appears
with the mapping of bytes of option (a or.byte, op.byte 2).
The choice of position keys P + and P-made, adjustable parameters - the volume buttons + or - on the remote.
To exit the service shake the TV button on the remote and
TV is turned off. Then remove the jumper from the point of reference for XN10 monoshassi.

* * * Entering the service menu in the devices 'HORIZON'


model DTV700, 710


On the remote user:

  • adjustment 'Volume' put a "0"
  • to press the mute button ()
  • push button timer ()

Adjustments in the "Tools" button switches on the ring, "P +", "P".
The value of the setting, change the button "+" "-"
Remembering the value adjustment is made separately for each option by pressure green buttons on the remote.

* * *

model CTV730


1. Jumper on the control point of contact SHTST XN102.
2. In standby mode, while, on the remote user to press in order:
"Status" (), then the "SL", then "off. Sound" (), then the "standby mode" ()
Entering the "Options", "Geometry", "Tuner", "Options" and "Reset." :

  • menu selection button "P +", "P" button menu connection "SL"
  • cursor set to the option adjustable button "P +", "P-" buttons to adjust the parameter "+" "-"

Going techno-menu button - "AV", and output in the TV mode button "TV". The set values ​​are automatically stored.

* * *

STV model 660.661


Connect the TV button "Power" at the closed pre-
SHTST contacts on the control point XN10. After heating the tube to press the "Menu" (SL)
Set the desired option byte button "P +", "P" and the adjustment button "+" "-".
Exit the service button "TV" set values ​​are automatically stored.

* * *

Model STV690


push the button on SB1 SHTST and hold before the
message "PW" or "Parabola." The call control button byte "Status" () on the remote control is made.
Output from the "Tools" mode button "TV". The set values ​​are automatically remembered.
model CTV676


1. Jumper on SHTST-676 pins 1 and 2 control points XN11.
2. While in standby on the remote user to click in order:
"Status" (), then the "SL", then "off. Sound" (), and "standby mode" ().
To save the results in the "Set Up TV" push "OK."
Return to the previous menu, click "TV".

* * *

الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس مود - HORIZONT   الأربعاء يوليو 20, 2011 7:15 am

Model STV670


When disabled the device by remote control or front panel push button "AV" and
holding it, click the "Network" turn on the TV. Button "AV" to hold
the appearance of a glowing screen. On-screen message IF38, 0AFC3 appear to be that
indicates the inclusion of "service" mode. In the absence of luminescence
soft screen rotation to adjust TDKS "accelerating" upward to achieve the glow of a pattern on the screen.
Set the desired byte option buttons "P +", "P" and the adjustment buttons "+" "-".
Exit the service button "TV". Values ​​are stored automatically installed.
* * *
model CTV664 (11AK-19shassi)


1. On the remote user to press the blue button, then 4, 7, 2, 5.
To memorize the values ​​of all the adjustments needed after leaving the "Service" mode to transfer to standby TV.

* * *

model CTV664M (AK30 chassis)


1. Button on the remote user "SL" pressing, then 4, 7, 2, 5.
Exit the service button "TV". To memorize the values ​​of
after all adjustments exit the "Tools" should be translated into standby mode TV.


* * *

model CTV678/698


On the remote control technology (RC6-7-5T) push button "-/--".
Exit Service "TV" button. To memorize the values ​​of
all adjustments after exit from the "Tools" should be translated into TV mode on duty.

* * *

Entering the service menu Horizon 55CTV-678T-I (12.7 chassis)


Click through the remote control menu image attached to the TV and dial
digital buttons of the remote 9301.
To exit the service push the 0 key.
Red, yellow, green and blue buttons are used to set the geometry characteristics,
menu IF and WB, respectively.

* * *
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس مود - HORIZONT   الأربعاء يوليو 20, 2011 7:16 am

TV Horizont 37CTV-664DT-I-1 chassis 11AK46-5

(OFC (Vestel/ST95195C7B1 / T49P018), STV2248C) - TV / DVD.
Enter the service mode:
1. On the remote home at a time to reap: MENU and the code 4725.
2. On the unit to press the button and then left MENU 4725 in the Soviet remote RC-5.
For a perfect control TV MAK Maxim (new) code 1343 is suitable. Remote Control RC-5 has a control person.
In sub-Geometry input - the button is green, ten lines there. Exit and Save - TV button.


[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

* * *

TV Horizont 70CTV-694T-I-16,

chassis 11AK37-8 (10).
ST92195C7B1/OER (T3x405 Vestel), STV9306, STV2248C, UV1315 = KSH1352E.
Enter the service mode: press the button on the remote: MENU button and the code 4725. Exit from service: Menu.
Power supply voltage + B 150-155V.
The photo option is not geometry! Entering the table geometry options - push button on the green button.


[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

* * *
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس مود - HORIZONT   الأربعاء يوليو 20, 2011 7:18 am

Enter the service rezhim.CTV733
1. Jumper on the control point of contact SHTST XN102.
2. While in standby on the remote user to click in order:
"Status", then "SL",, then "Off. Sound," and finally "Standby"
Log in Settings, "" Geometry, "", "Tuner", "Reset", "Options", "key".

  • menu selection button "P +", "P" button menu connection "SL"
  • switching option button "P +", "P-" buttons to adjust the value "+" "-"

Becoming a Techno-menu button "AV", but in TV mode output button "TV". The set values ​​are automatically stored.
Removing the key is in the "Settings" menu: 1st way to enter the
service in the line "key" - the numbers are, for example, 25 800. Include them in the "Options" menu. The code will be removed.* * *
TV HYUNDAI H-LCD2202.


Ingredients: Scaler: U5 Novatek NT68565FC, Proc: U21 TDA15021H/N1C00,
NT68F631ALG, Submicom: U6 Novatek, Audio: TDA1517, NVM: U8 24c16, Tuner: TDQ-6f6/T126CW.
Enter the service mode:
In the native remote Repeatedly press CALL, then RED, then GREEN, YELLOW and then the last CALL.

* * *


TV Hyunday H-TV2910SPF - 5Y19 chassis


CPU LA76938N 7N-58R2.
Entering the service menu with the remote user: VOL - to remove
to 0, then MENU, and code 6568 in the «FACTORY».
Then the timer button to «B / W Balance», push again - to transfer
in «Adjust Menu 0". Go to «Adjust Menu» forward button timer
back - click DISPLAY. Election to the «Adjust Menu 3" Setup Select quantity
"1" adjustment menu extends from 5 to 22. In the «B / W Balance» MUTE button
on / off Vertical. Exit: RECALL.

* * *
TV Hyundai H-TV2902PF, ES6510T chassis.

1. Entering the service menu: press the remote control buttons in series «SM», INFO (with a cross box) and «CH I / II».
2. Entering the menu you need: Geometry - buttons "1" and (or) "2"
White Balance - button "3"
option 1 - button "4"
option 2 - a button "5".
3. Election parameters: buttons «PROG +» and «PROG -» on the remote.
4. Change the value of the parameter: buttons «VOL +» and «VOL -» on the remote.
5. Getting in tune mode G2: button "0" remote.
6. Exit adjust G2: button «PROG -» Remote Control. Allowed simultaneous exits the service menu and G2 (p. 7).
7. Exit from the menu of service: the button INFO (square with a cross) on the remote.

* * *
TV HYUNDAI HU-D25A,

Chassis 5N11, processor S3P8849XZZ-A089.
Enter the menu service: press simultaneously switch and VOL + and VOL - on the panel. Search for "MENU".

* * *


TV Jinlipu 3728

(Another chassis), LC863532C-57Z0, videos LA76818A, pamyat24C08,
Tuner - firms JINHIN UVC68K5VCA U230095 0603-0466.
Entering the SERVICE with a remote control staff - is possible with remote control, described below.
For information: television without EEPROM starts, on a blue background with
at the bottom - the inscription E2PROM CLEARING, after 9-10 seconds TV is
automatically in AUTO with digital display (change)
the frequency of infusion channel program is not as tuner type in service is exposed.
The behavior of the memory of "pure» (FF) - is similar.

* * *


الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس مود - HORIZONT   الأربعاء يوليو 20, 2011 7:19 am

TV Jinlipu CD3730

- Entering the service menu with remote staff «54J8»
LC863532C-57Z0, LA76818A, LA7642N, 24C08, LA78040N, tuner
(UV66K5VEA) VS1-1A5-DK, RC - 54J8, chip compound
flooded ("drop"). What contacts should close on the remote control to
vhozhdeniyav service? Mention of this processor and a TV in the subject.
According to the information:
1. Entering the service menu: Menu, configure the program - change - quickly in 2483.
2 Entering the service menu: penny lower the upper left
button "MUTE" (though the output IC 19 counterclockwise to the left
right) + penny lower the upper right button ON / OFF (output in the compound is not tracked).
Answer: Yes, indeed, it works (photo below shows, for which thanks to a separate Polomnik).


[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

* * *

TV Jinlipy (Chinese).

Processor 8891CSCNGV12 FM24C16 DSC25-03P78 TDA1030.
Enter the service mode: remote control, ground red circled in the photo.

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

* * *
الرجوع الى أعلى الصفحة اذهب الى الأسفل
 
سرفس مود - HORIZONT
استعرض الموضوع السابق استعرض الموضوع التالي الرجوع الى أعلى الصفحة 
صفحة 1 من اصل 1

صلاحيات هذا المنتدى:لاتستطيع الرد على المواضيع في هذا المنتدى
أشرف عثمان للإلكترونيات :: قسم الصيانة - Repair-TV :: أرشيف السرفس -service-mode-
انتقل الى: