جميع سرفس مود -AKIRA

AKIRA chassis A21T01 CT-21FDS1
CPU: 87SK38N-2B46
Log into the service mode:
1. In
operating mode, turn the volume down to 0, then press and hold the
front panel button VOL -, press the button on the remote DISPLAY (while
the TV goes in the S-service mode).
2. Release on the front of the TV button VOL-, press the button on the remote DISPLAY. Repeatedly press the TV front panel VOL-button, and again press DISPLAY, while the TV will switch to D - extended service.
CH +, CH-mode selection settings
Change settings for VOL +, VOL-
Exit the service mode: STANDBY.

AKIRA chassis 3Y01, 3Y11 CT-14HS9, CT-21NI9CP
Log into the service mode: (MENU), (MENU), (RECALL), (MUTE).

AKIRA chassis 3Y11 CT-14SX9R
CPU: LC863328C
Log into the service mode: (MENU), (MENU), (Q. VIEW), (MUTE). Mode switching button (SLEEP) Exit the service menu - the button (MENU).

AKIRA chassis 5P60
CPU: TDA9384PS/N3/3
Log into the service mode: - press the button consecutively RC CLOCK, PM, TIMER.

AKIRA chassis 11AK19PRO CT-2155
CPU: VESTEL 19V1
Log into the service mode: Press the blue button to enter the SETUP menu to press buttons 4, 7, 2, 5

AKIRA chassis CN-18ED CT-25CGS5AN
CPU: CH08T0605/A8827CSNG
Log into the service mode: Set the volume to 0, then press the MUTE button on the remote and holding it - MENU button on the bar TV. In support of the entrance to the service appears on the screen S.
To exit the TV transfer mode standby.

AKIRA chassis ETA-1 CT-14CAS5CP
CPU: TMPA8873XANG
Log into the service mode: Set the volume to 0, then press the MUTE button on the remote and holding it - MENU button on the bar TV. In support of the entrance to the service appears on the screen S.
To exit the TV transfer mode standby.

AKIRA chassis SS1
CPU: LC863328A 5Y29
Log into the service mode: Press the button on the remote PROG, dial 6483. To log in 2 sub-menu, repeat the operation sequence.
To exit and repeat the procedure. Or from the service panel would issue the command FACTORY.

AKIRA CT-21FGS1
CPU: 8821CPNG4RJ1
Log into the service mode:
1. In
operating mode, the TV turn the volume down to 0 value, then press and
hold the button on the front panel VOL-, press the button on the remote
DISPLAY (while the TV goes in the S-service mode).
2. Release on the front of the TV button VOL-, press the button on the remote DISPLAY. Repeatedly
press the TV front panel VOL-button, and again press the DISPLAY (in
this case the TV should go into service mode D - extended service).

AKIRA 21HAP1/BE
CPU: TDA9381PS/N2/2I1318
Log into the service mode: Press MENU on the remote and enter code 8500

AKIRA 21LGS1/CE
CPU: 8853CPNG6EG1
Log into the service mode:
In the working mode of the TV to reduce the volume to 0 value, then
press and hold the button on the front panel VOL-, press the button on
the remote DISPLAY (while the TV goes in the S-service mode).

AKIRA CT-15RAP5/BN
CPU: TDA9351PS/N3/2/1804
Log into the service mode: close the jumper "service" on the board.

AKIRA CT-29TX9AS
CPU: TDA9386PS/N3/3
Log into the service mode: Set the English language, then press the remote control: CLOCK, PM, TIMER. Remember - STB.
Exit the service menu: - DISP.

AKIRA and other
AKIRA SERVICE
AKIRA 3S10
a. Log in to the service by pressing MENU, AV, ANAL buttons at a time, or
pressing SERVICE (to the right of
button MENU, we can add this button for easy entry into the
service. Click OK, to enter into
Service 2.0 and Design mode.
b. To exit, press the PP or STANDBY.
Option1: b4 ---- always set 0
Option2:
B0 ---- 0 is usually set can reduce the noise pattern
b1 --- 0 is usually set to automatically review the shade
NTSC
b2 --- 0 is usually set the contrast, make the picture better
b3 --- 0 is usually set the contrast, make the picture better
B4 --- 0 is usually set to increase the color
Option3:
B0 ---- always set 0
b1 --- MUTE output pin MCU's power to choose. Set to 0
using the TDA1905 (MUTE = 0 V), set to 1 when
use TDA7496 (MUTE = 5V)
b2 --- 0 is always set
b3 --- 0 is usually set
B4 --- usually set 0
Option4:
Only one AV input: b0 = 1 b2 = 0

Two AVS I: B0 = 1, b1 = 1
If necessary, SCART, b0 = 1 b3 = 1
HPOS OSD: OSD left and right position in order to establish 001
VPO OSD: OSD up, and at a position at 01
HPOS TXT: teletext character left and right of
VPO TXT: teletext character above and below the position
LOGO set:
1 Set OPTION1 B0 = 1.
2 The last point white balance adjustment mode is used for
LOGO is the maximum setting
12 characters to choose from. Use the PROG + / -, VOL + / -
Buttons to change the character. The most significant bit denotes the number LOGO heroes
it can be installed
among 1, 2, 3, 4, 5, 6, 789ABC
Note:
The above adjustment is recorded in IC002 (24C08EEPROM).
IC002 used in product lines should be well-written data.
If we use
blank EEPROM (internal affairs data are presented in FF), or suitable for
EEPROM 3S10 chassis, it will be initialized (all data in 00) and
special data
recorded automatically when switching AC
power for the first few seconds. The values ​​are as follows:

Order 3S10 chassis (for reference only)
1. Just before the line:
A. B + voltage is set
B. VCO adjust
C. If the trap set for NTSC-M system. This can be done in
According to your FA
choice. We can customize a perfect LC101
NTSC-M system, the quality of photos and did not breach the signal SIF.
2. Final Assembly Line:
A screen and adjust the focus voltage
B. TAGC set
C. The white balance is set
D. H / V 50 central and Amp set up for PAL
e. Min Brightness adjust
F. V AMP 60 and under shade for NTSC
* * *
AKIRA 5P60
Log in to the service:
Press CLOCK, PM,, TV SET to enter the service. Press the key to the 0-9
input. Select "
PROG + "and" PROG-"keys. Adjust using the "VOL +" and "VOL-"
Keys. Click the "+"
key to exit.
B. Focus adjustment.
Get Ya monoscope pattern.
II. Television work in a dynamic status.
III. Adjust the focus knob PPL to get a clear picture.
C. Screen voltage regulation (KEY 0)
J. TV on "TV" mode "Standard", there is no input signal.

II. Pressing the key CLOCK, P.M. in turn, enter the factory mode.
III. Pressing 0.
IV. Adjustments handle FBT, to get a horizontal line
beam weaker.
B. Pressing other keys to move to a normal state of operation.
D. The vertical size and configuration of contact pad (KEY 2)
I. Get the 50Hz standard picture. TV expose to
standard provisions
5VSL set for half the standard picture,
set 5SCL
to get a vertical picture of Pin cushion in good condition
set 5VSH
a vertical line in the center of the picture in the center of CRT
screen in the manufacturer's instructions.
* * *
Akira 11AK19PRO (CT-2155) Press the blue button to enter the SET menu
Press the buttons 4, 7, 2, 5
* * *
AKIRA CN-9EA
1. entry into service: Use the service console K10N-C1. Set
volume to a minimum.
Press MUTE on the remote. Hold down MUTE, press the MENU button on the TV
to
D appears on the screen.
2. CHOICE OF ADJUSTMENT
Each push red or green button on the remote transmitter

Management changes in control points BUS DATA.
Service modes
1. SUB brightness
1. Get the color signals.
2. Set the maximum contrast and brightness to medium.
3. Set color to medium. Enter the TV to SERVICE.
Select BRTC, clicking on the item
adjustment buttons on the remote control transmitter and
a set of data in 30 by clicking on the data adjustment. Operation
TV for 5 minutes in the regime.
4. Adjust the BRTC fuzzy data until the image appears on the
High-bright screen area and not too dim picture
on the low-bright areas.
5. Set the contrast and brightness to the maximum or minimum, and then
check out the normal rotation of photos.
6. If the image is dark, when the contrast and brightness
establish minimum or become brighter when
set to maximum, and then adjust the data for BRTC
normal picture.
SERVICE MODE ADJUSTMENT
images, sound and geometric correction are also stored in the EEPROM.
* * *
AKIRA SS1
1. "Enter" and "go" factory methods modes:
1.1. Plant Type a password: (use a normal remote
Management)
1.1.1. Russian television as a condition and click the remote "Prog" key, and
Follow the "6", "4", "8", "3"
1.1.1.1. Repeat the same step "1.1.1." Conclude "adjustmentcondition
White Balance "
1.1.1.2. Repeat the same step "1.1.1." Enter into "factory mode"
adjustmentcondition
1.1.1.3. Repeat the same step "1.1.1." Enter into "factory mode"
Setting condition
1.1.1.4. Repeat the same step, "1.1.1" to exit the function
plant

Akira CT-14CAS5CP. ETA-1 chassis.
Ingredients: 8891CSBNG6KF8 CPU, 24C16 memory, STR-G5653 FE, LA78040 KR
TFA9842AJ VLF, TAF5-C4I23 tuner, BSC59T TDKS, 2SD5023 HOT.
Entry into service: Volume set to 0, then press on the remote
MUTE button and hold it, MENU button on the device. In
confirmation of entry into service there on the screen S. To exit
TV menu service be transferred to mode standby.
* * *
Akira CT-21DSL5R. ETE-3 chassis.
Ingredients: TDA11136PS/N2/3 (PB-01) processor, FM24C16pamyat, CQ0765RT PI
TDA4865AJ KR, TFA9842AJ VLF, TAF5-C4I23 tuner, BSC590 TDKS, 2SD1557 HOT.
Log in services: the volume set to zero, then press
consistently and hold Mute button on the remote, then Menu key on the keyboard
local.
Exit - on the remote control POWER.
* * *
Akira CT-29DR9A. S33 chassis.
Ingredients: LC863320A processor, memory 24S08, 2SC5299 FE, LA7840 KR
BSC25-3802E TDKS, 2SC2553 HOT, TA8256 ULF.
Entry into service: a remote control jumper PIN16 and PIN7 a chip - it is
SCREEN button is. Peremknite in remote and PIN16 PIN8 a chip -
this button will FACTORY. To enter the menu, double-click FACTORY -
you're in the menu.
* * *
Akira CT-21FD9M. H-704V chassis.
Ingredients: SDA555XFL processor, STR-G6656 FE, TDA7297 VLF, LA7845K KR
NN5198K video, MSP34X0D stereo.
Entry into service: With Remote Control -
DISPLAY-MUTE-SLEEP-FUZZY-DISPLAY.

* * *

AKIRA-CT-29FSAN Chassis 5P60.
1. Push buttons on the remote control in series «SM», small screen with plus and
CH I / II.
2. Push the remote control consistently CLOCK, then PM, then TIMER.
Exit: DISPLAU written, but I have a button VYKL.ZVUKA.
TV AKIRA CT-14HS9.
But its composition is not within
corresponds to a given chassis. Ingredients: Processor ST6-ELANE2.
video STV2118B. Manpower TDA8174, sound chip TDA1905.
Described chipset looks like a very "ORSON CT-2120".
Entry into service: SKIP, then VOL-, then FINE TUNE, then -.
* * *
AKIRA CT-21HS9C (S)
CPU LC863324A
Login: Menu - Menu - Q. View - Mute

* * *
AKIRA CT-2155, CT-2160
Processor: VESTEL 19V1.0NT
Log in to the service. Press MENU (INSTALL), set the cursor on the line
"Settings". Then click the series 4
=> 7 => 2 => 5

Akira CT-14PF9, CTF21TF9R, 3Y01 chassis.

Processor:
LA863324A.
On the remote control buttons to press consistently: MENU, MENU, V. WIEV (or
RETURN), MUTE. Translation on the menu button is being implemented SLEEP. Exit -
MENU.
* * *
AKIRA CT-29PQ9AS
Entry into service with the remote user: consistently push
button CLOCK ---> P.M ---> TIMER. Exit -> Display. Remember -> Standby.
Before entering the service nadopereyti from Russian into English in
user menu.
* * *
AKIRA CT-14SX9R, chassis 3Y11,
percent. LC86332C.
Here is an excerpt from the manual: There is no way in the natural entrance
Manufacturer menu, the user must follow the instructions
below.
1. It is necessary to enter the menu 'Picture'.
2. Push the back button of the channel.
3. Push button switch off the volume.
After appropriate action menu will be shown the manufacturer.
The user can use the button "Sleep" to modify
menu page of the manufacturer and use the button "User Menu" to exit
Menu plant.

* * *

AKIRA CT-29XG9AN.

This chassis 5P60, entry into service
menu as follows:
1. Push button CLOCK ..
2. Push button P.M
3. Push the button TIMER (which is shown as a clock).
4. Quit-button MENU.
* * *
AKIRA CT-2155 (11AK19PRO chassis).
Processor - VESTEL19V1.
Push the blue button in the INSTALLATION menu and push enter
consistently buttons 4, 7, 2, 5.
* * *
AKIRA CT-2 5FS9A,
CT-25DS9A/AN, CT-25LS9AE/AIU,
CT-25RIX9A, model CT25IUI9A AT / / AN / AE / ATS, CT-25XC9A/AIM, model
ST-25NX / AE/9A (SKD) / AN, ST-29FS9 / C / A / MK1AT/ATS / MTS/MK1AIU,
CT-29DS9AE/AIU/AW, CT-29LS9A AN / / AE / ATS / AT / MTS, CT-29IUI9A / AN / AE / AT,
CT-29PF9A/AE, ST-29NX9AE/AIU model, CT-29PS9AE, CT-29TK9AE/AIU,
CT-29SK9AE, model CT-29TJ9 AN / AE / ATS, CT-29TW9AN, CT-34DS9A, model
ST-29XC9A / ATS / AE / MC 1AM/MK1 AE / MK1 AT/1ATS/MK MK11U, ST-34LS9A/AN,
CT-34SG9AN, CT-34PF9A / AN / AE (SKD) / PF9C, CT-34TP9/A/ATS model for
51U11shassi.
To form teams of service to the following improvements to
in remote staff:
for the formation of the team «Screen» bridged pins 7 and 16 circuits
Remote control with buttons;
for the formation of the team «Factory» more bridged findings 8 and
16 circuit panel with buttons more.
To enter the service menu on the control panel at the same time under pressure
button VOL +, VOL-, and holding them, connect the TV's power.
Another option enter the service: After connecting your TV
click twice on the remote control button Factory edited.
* * *
LCD Akira LCT-27PBSTP / R. L27W18-15 chassis, 782-L27W18-150A.
It consists of:
MSP3410GB8 V3 782.L37W25-6900 tuner (two pieces) JS-6B2/121A2,
Processor: Tmos PanelLink SiI9011CLU QF5381.1A
0550 AD01AD2.
Entering the service of manual:
Press MENU, then -/--, then 9, then 1, then 8. Successively
one by one. Then enter the factory menu, press SLEEP,
to select a page adjustments, exit the factory menu: it is necessary
press MENU.

* * *

AKIRA. Model ST-2025.
Defect: on the canals is not
settings. Voltage setting does not change at all channels for 27 V
selector. Suspected defect processor SDA555XFL. TV fix
helped rewrite 24S16 memory.
* * *
AKIRA TB1238
3. Log in to the service:
Step 1. Press 12
Step 2. Press 38
Step 3. Press MENU, to cause POS.LOCK menu
Step4. Press MUTE
Step5. Press the numeric password 1, 2, 3, 8. Then the TV goes into
service, and in the corner
will be "M".
4. Under the adjustment mode, you can select the desired item by pressing ""
button and adjust the values
items by pressing "" key.
5. When adjusting the default, then restore the data from previous
or set the table
follows.
* * *
Akira 21FGP1BN.
Ingredients: microprocessor 87CM38N-3GN5 (87CM38N-2B46), AT24C08 memory
Video TB1238AN, KR LA7830, FE 2SC4429, ULF AN5270, HOT 2SD2499, SECAM
TDA1275AZ.
Entry into service: 1 method. In the working volume to turn down 0
then push and hold the button on the front panel, VOL -, press on
RC DISPLAY button (the machine enters the S-service).
2 method. On the TV front panel button to release VOL-, pressure
button on the remote DISPLAY. Secondary push the button on the panel VOL-
TV front and again to press a button DISPLAY, while
TV to go D - extended service. CH +, CH -
election mode settings.
Changing the values ​​of VOL +, VOL-. Exit service STANDBY.
* * *

AKIRA 21HS9.
Entering the service menu: SKIP, then VOL-, then the AFT, and then find
UHF only option and make an "N" with a green "MUTE". Seem all
ranges. Well, with all other geometry and there are understandable. Exit
button (do not know how to curse her) choice of the contrast, brightness, etc.

* * *
Akira CT-21JUl5R.

on the front panel of the TV
Set volume value "0". Push a button on the remote control (MUTE)
and holding it push a button (MENU) on the TV.

* * *

Akira 21PZS1.

Processor TDA 9381 PS/N3/3.
Entering the service menu: MENU 8500.
* * *
AKIRA CT21VBS3WN.
The processor (on sticker)
NTDA9381C312A. 24s08 memory. The chassis is not defined. Getting in
Service menu: select channel 12 on the keypad, then 38 channel,
then MENU, and reaching up to the position POS.LOCK, to press MUTE and 1238.
Exit - OFF.
* * *
Akira 29WHP3ANZ. UOC-TDA9384 chassis.
Ingredients: TDA9384PS/N3/3 CPU, 24C08 memory, KA5Q1265RF FE, TDA8351
KR, TDA7495S VLF, 2SD2553 HOT.
Entry into service: from the working mode dial: MUTE, DISPLAY, -/--,
DISPLAY, MUTE.
1.7 buttons election in the service menu. Exit - EXIT.
* * *
AKIRA 21WHP3/BN.
Instead of the changed NTDA9381C38ND (on sticker) on NTDA9381 - 7NA (at
sticker). Replaced one by one.
Entry into service, for some reason, as well as for the UOC-TDA9381 (C312) A chassis.
Push the button "MENU", 8,5,0,0, choose the menu buttons from 0 to 9.
Output: Standby mode 2 times.

* * *

TV AKIRA CT-21FSL4R.
Processor TDA12062H1/N1D00,
Memory 24C16WP (3,3 v) (Checksum 0A74-AutoProg), Block
Power STRW6753, Inline transistor D2901, Correction IRF630, HR
IC STV9325, Sound TDA2615, tuner digital. ETA-SF03/12, picture tube - 21 "Flat.
Entering the service menu: With the desktop, press the MENU button on the quick
remote, and five Q. VIEW. Switching on MENU, go to service TV / AV.
* * *
TV AKIRA CT29NX9AN (5N11shassi).
Entering the service menu.
1 - From the disabled by pushing and holding the TV VOL + and VOL-buttons to connect the network button.
2 - In the working jumper pins 2 and 4 x service CN601 (GND and ADJUST).
On the screen there is the inscription "KWTVA COMPUTER 11-23".
Then click on OK button on the remote. There is a menu "KWTVA SERVICE 11-23".
* * *
TV ALBA TVD-3406.
Ingredients: CPU M37160M8H-067FP, M61266
Entering the service menu: jumper pins 1 and 5 chip T3833-002J,
exiting and saving the settings - the button MENU.

* * *

TV ARVIN CT1425GUE-1
Shassis - Stickers
on the board: CCE - VO. E166702. CHANGZHOU.
Microprocessor TDA9381PS/N2/3I VC3RD90 CD4420 10 FM-OSD. On the label - (NTDA9381-8ND).
Tuner - XG6SVD86B1, Memory - 24LC08B, Sound - AN7522N, Human Resources, M / S - D9302.
Entering the service menu: press MENU and quickly dial the code 8500.

* * *
TV Avest, AKIRA 14FES1, Shivaki STV-2565, SHIVAKI, TRONY 21TS89.
Popular as PAEX0078A chassis.
* * *
Option One: Microprocessor: EASTKIT 8821CPNG4RJ1, LA78040, 24C16A, D2499, D2498, LA4267.
Option Two: Microprocessor: 8821CPNG4RJ1, D2492, STV9302A, C5586.
Version of the third: AKIRA 21FZP1, microprocessor: 8821CPNG4RJ1, D2492, STV9302A, C5586.
Enter the service mode: you have to do the following manipulation:
Enter the menu button installation (INSTALL), then press the button on
the remote control in sequence as follows (4), then (7), then (2), and
(5). Find ADJUST menu item (all control over it change).

TV AVEST 54TTS-02 \ 09 \ 39.
Microprocessor TCL M5V-1P \ 87CM38N-1E75.
Enter the service mode: Push button VOL-panel TV at the same time on the remote control Displey.
Buttons held until the appearance of the letter S on the screen apparatus.
Go to menu click MUTE. Exit POWER OFF.
* * *
TV AVEST 54TTS-02/88/16/90.
Microprocessor TCL A02V-01T/87CM38N-3GP2.
Enter the service mode: - simultaneously press the button VOL-
on the TV and Displey on the remote. The buttons keep
before the on-screen TV letter D. Go to menu click MUTE. Exit from the menu POWER OFF.
* * *
TV AVEST 64TTS-02.
Microprocessor TCL-A18VO1-TO.
Enter the service mode: Push button VOL-panel TV
and not letting it press on the remote Displey until the symbol D on-screen TV. Release the button VOL-.
Go to service menu - programs digits on the remote.
In any of the sub-menu options for the transition buttons P + P-Adjusting buttons V-V +.
Exit from service POWER OFF.

* * *

TV AVEST 72TTS-02PS16/06/90/86, 64TTS-02PS90/88, 72TTS02-PS.
Microprocessor TMP87PS38N/M13VR2V1.
Enter the service mode: - VOL-button on the toolbar click the TV
Displey both on the remote. Button to hold
appearance of the D symbol on the screen of the device. Go to menu click MUTE. Exit the service menu of the POWER OFF.
* * *
TV AVEST37/54TTS-01
Control processor LC86F3548A 1J1.
Enter the service mode: Menu first - simultaneously press
VOL-button on the TV remote control and OSD. Buttons to hold until the TV screen symbol S.
On the Go menu, click MUTE. Exit the service menu of the POWER OFF.
Second menu: press the sync button on the panel VOL-TV and remote
control TV / AV. Buttons held until the appearance of a character on the
screen S TV.
On the Go menu, click MUTE. Exit the service menu of the POWER OFF.

* * *
TV AVEST 54TTS-04.
Control processor NTDA9381S38NS.
Enter the service mode: hidden on the remote control button the bottom
row of buttons available on the SOUND button on the right, under
nakleechkoy.
After pressing this button, the letter M appears buttons 0 ... 9 menu items, select the service.
Exit the service menu of three button POWER.

* * *

TV AVEST37/54/64/72TTS-01
Control processor LC863328A 5W63.
Enter the service mode: - to put pressure on the remote control hidden in the
button. Hidden button on the remote control between the VOL-and the word or the buttons P + and CH +.
Office of the menu is a hidden fifth pressing of a button.
Exit: Press the secret button
* * *
TV AVEST37TTS-02.
Microprocessor TMP87PS38N.
Enter the service mode: synchronous to pressure a few times
VOL-button on the unit and Displey on the remote. Buttons until you hold the D symbol on the TV screen.
MUTE button on the menu go. Exit from a menu of service POWER OFF.
* * *
TV AVEST TRB2158.
Control processor 87CK38N-2B46.
Enter the service mode: turn down the volume to 0. Login - pressure
VOL-button on the toolbar and TV simultaneously on the remote Displey. Button to hold the symbol S on the screen TV.
Go to service menu P + P-. Adjusting the values ​​of the parameters V-V +. Vertical Size HIP. Exit button POWER OFF.
* * *