قسم السرفس -LCD-CRT- Service Mode

AIWA 1402, 2002KE, 2102KE
Conclusion 7 TVPO2066 D05/047 processor to activate the service mode. On-board TV
is a special button S009. Clicking on it simultaneously with a button (DISPLAY) on the remote control, enter the service menu.

AIWA TV-C142, TV-A215
CPU M37220M3-150S. To activate the test
mode, press the hidden button on the remote,
located between the buttons 8 and SYSTEM. (under the false panels) to
cancel the test mode, use the same knopkupovtorno. After replacing
memory chips to perform the following. Use the remote-type RC-6VT06.
86-LB4-951-010
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
1. Press the TEST button to activate the service mode.
2. Press DISPLAY on the remote control, and make sure that the screen such as in Figure 1.

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig. 1.
3. Press the CHANNEL button on the remote control, and then move the red
marking on the K3 and the data set as in Figure 2, using the buttons
VOLUME +, -

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig. 2.
4. Then move the cursor to the K4 and set the data as in Figure 3

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig. 3.
5. Press DISPLAY, then press FINISH (hidden under the false panels)
6. After the appearance of a few seconds on screen
Posts INITIAL power automatically turns off.

AKAI CT-2119PD/PDT, U2E/Y2/Y2E
On the TV at the same time press the button VOL + and VOL-and hold them, turn on the TV.
Exit - (POWER OFF)

AKAI CT2161 CT2565 CT2567 CT2865 CT2867, Chassis SP
On the keypad press the button - (MUTE) (OK) (TV). Data record (OK). Out - (TV)

AKAI CT2899, 7171 Processor CCU11 \ 12, chassis B-E2
For CCU 11 (. °) (C) (H), CCU 12 for a screwdriver Press contact in the hole
about the keyboard and press the right button (S). Exit - (LOAD)

AKIRA CT-14PF9
On the keypad to dial: (MENU) (MENU) (V. WIEV) (MUTE) (SLEEP) - turning the pages. Exit - (MENU)

AKIRA CT-21HS9C (S) CPU LC863324A
Login: Menu - Menu - Q. View - Mute

AKIRA CT-2155, Processor VESTEL 19V1, Chassis 11AK19PRO
Press the blue button to enter the SETUP menu to press buttons 4, 7, 2, 5.

AKIRA CT-2155, CT-2160 Processor: VESTEL 19V1.0NT
The entrance to the service. Push MENU (INSTALL), put cursor on "Settings".
Then click successively 4 => 7 = 2 => 5

AKURA, CROWN, MINOKA CX25/26/34 CR20NT CR1406FT MK1498N / N MK2183 / N
Conclusion 8 processor TVPO2066 D05/047 to activate
service mode. On-board TV is a special button S009. Clicking on it simultaneously with a button (DISPLAY) on the RC
included in the service menu. Exit - (TV / TEXT)

ALLSTAR 3750
Turning off the Hotel Mode: Select the program 38. At the same time hold for 3 seconds STORE and CONTROL + on
panel TV.
Enable Hotel Mode: Select the program 38. At the same time hold for 3 seconds STORE and CONTROL-panel TV.

ARAY ACT2130 Processor - LC863328A, video processor - LA76810A
Log into the service mode: Push button hidden (FACTORY) on the remote control, it also switches the menu.
chip remote SC7461-103 (pins 2 and 16)

AUDIOTON 5502 Chassis 10.3 90 ° MONO
Turning off the protection of children: Press UP & DOWN buttons together on tv's local control
and then switch on. You will see SERVICE MODE. Do not press any button, just power off the set, then on ..
Enabling the service menu: Press UP & DOWN buttons together on tv's local control and then switch on ..

BANG & OLUFSEN LX4500/5500 L4500/5500 MX3500/5500
Prepare
your TV, set: Brightness 32 Saturation 32, contrast 44. Click (TV) on
the remote control and lock for a minute (60 seconds) click PCB5, which
is located close to Terminals VM. Exit - (STOP) or (POWER OFF)

BEKO, Processor SDA20563-A512/A514, Chassis AR-3
While holding down the button on the TV (PROG-) (PROG +) toggle switch on the TV network. Exit - (POWER OFF)

BEKO CTV, processor SAA5563, Chassis 14.1
Close a chip RC legs 10 and 17. Exit - Close the remote control at the chip legs 10 and 17.

BEKO chassis 12.6 Processor SDA5535A049

• PICTURE MENU
  
• 8500"
  
• EXIT "850"
  

BEKO chassis 12.7 Processor SDA5535A056

• PICTURE MENU
  
• "9301"
  
• EXIT "0"
  

BLAUPUNKT IS63 (72) 1953 DIGITAL PRO, CPU MC68HC11F1, chassis FM640.40
Starting
the internal memory of the processor. Shorted to ground (earth) pin 1
processor (contact MP2) and turn on the TV to the network. Services (i)
(E). Output (i)

BLAUPUNKT MM63-13VT MM63-14HT, processor ZC88649P ZC88644P ZC424701, Chassis FM-240/00
Hold down the (i) to enable remote power switch. Exit - (POWER OFF).

BLAUPUNKT MS70-100 Digital PRO, CS82-100 Digital PRO, Chassis FM600.70 FM600.71
Click
(i) on the remote. Choose the position PROGRAMMIER OPTIONEN press (ME)
(AUX). Choose the position of SERVICE MODE Press (ME) (3) (2) (0) (0).
Exit - (TV).

BLAUPUNKT MS70-76VT, Processor HD6305Y1B80P, chassis FM100-30CTS
Log into the service mode:

• Turn off the TV with remote control
  
• Include a remote control, keeping ME on the local panel TV.
  

Adjustment using the (+) (-) on the keypad. TB: Brightness (on TV) -
vertical size, saturation (on TV) - the size of the horizontal volume
(TV) - centering on the horizontal fine adjustment (on TV) - centering
on a vertical,>-Select the sound standard Memory - ME (on TV) after
each adjustment. With the remote you can set the initial values ​​of
picture and sound settings, press the ME (on TV) - write to memory. Exit
- (POWER OFF).

BRAND Processors ST9093 ST92T93J9B1, chassis ICC9

• With the remote turn the TV into standby mode.
  
• Turn off the TV network switch.
  
• By pressing the blue button (VT) enable the network switch.
  
• Press the button again (VT).
  

BRAND, Chassis TX807
Push the purple button on the remote control and turn. Exit - (POWER OFF)

CIRTIS C-14/21/25/28M1/M2. Processor MC68HC705T10B
Close conclusions 13 and 23 of the SAA3010 in the RC.

CONTINENTAL CT1412. Processor ST6375
To enter the service menu to hold the button (+) (-) in front of the TV turn on the power switch.

DAEWOO CHASSIS CP-375 Processor DW5255M2, DW5255RM.
All changes in service are made only through a special panel.

DAEWOO KR20V1T
Switch the TV on channel 91. Hide clarity to the minimum. On the remote
control to press the (red) (green) (menu). Exit - (POWER OFF).

DAEWOO DTC-14V1/V3/V4/V5/U1, DTC-20V1/V3/V4/V5/U1, DTC-21V1/V3/V4/U1/U3, Chassis CP-002

• Select Channel 91
  
• Set the sharpness to minimum
  
• Exit Menu mode
  
• Fast sequence of buttons to press RED - GREEN - MENU
  

You should see the inscription Service Mode OSD
Exit the service mode - Power off

• Data Preset (D.P.) Adjustment
  
• Select Channel 91
  
• Set the sharpness to minimum
  
• Fast sequence of buttons to press RED - GREEN - BLUE - MENU
  
• You should see the inscription DP OSD
  
• Channel Up, Down - choice
  
• Volume Up, Down - Management
  

DAYTEK DCT-2062-S
On the keypad (DISPLAY) - (MUTE) - (SLEEP) - (FUZZY) further pressing
(DISPLAY) or (SLEEP) introduces a TV set in the service menu.

DUAL HANSEATIC SCHNEIDER M4055, ST6714, CTV2703. Processor CCU09 \ 10 \ 13. Chassis DTV-1
Pressed simultaneously (S) on TV and the button (C) on the remote control

DUAL HANSEATIC SCHNEIDER TV5504, TV5520, TV5525. Processor STV6385. Chassis TV-4
Press both the blue and red button on the remote control. Immediately press simultaneously (P +) and the (VOL +) on TV.

DUAL HANSEATIC SCHNEIDER TV1170, STV6156. Chassis DTV-2
Simultaneously press the button - the remote control (C), and the service button located on the bottom row console.

ELEKTA CTR-2145, DTV21F4 CPU LC863320A, videoprots. LA76810A
Log into the service mode: press a hidden button (PROD) on the remote control right of the Vol +
it also switches the menu.
chip remote SC7461-103 (pins 2 and 15)
chip remote LC7461 (pins 2 and 16)

ERISSON S14, ERISSON 2120 or ERC 21NI60 chassis 3S10
Processor: ST92185BN4B1/PBI 3S10B-ENG/RUSS
videoprots.: STV2248C
Log-in service:
Menu - AV - ANAL
OK - a choice
PP - output

ERRISON 2102, 2103 Processor: S3P8849XZZ-AQB9
Close contacts 2 and 4 of the connector CN601. (ADJUST and GND)
Appears on the screen "KWTVA COMPUTER 11-23"
Then click "OK" button on the remote.
Menu appears on the "KWTVA SERVICE 11-23"
OPTION 5473176706

ERISSON S14 Processor: LC863324A, videoprots.: LA76810A
Log into the service mode: In the operating mode press the sequence on the remote: MENU - MENU-Q.VIEW - MUTE
OFF TIMER - regime change menu
MENU - write the new values

FINLUX 4028D. Processor SDA20160
Immediately after the TV issue the command from the console (PRG) (EXT). Exit - (POWER OFF).

FINLUX SERIA 5000. Processor SDA20320
Immediately after the TV issue the command from the remote (TV) (PRG) (EXT). Exit - (POWER OFF).

FINLUX 3021. CPU SDA2080
Click on the (N1) front panel TV and
quickly press the button which is located to the left of the button
(N3). Exit - click on the button located to the left of the button (N3).

FUNAI TV-2100A MK-7 MK-8
Close to each other 2 and 14 feet in
the RC circuit D6600A. Button 6 mode "PICTURE SELEKT" switch character -
a graphical display information OSD. It only works with an R-514

FUNAI TV-2100A MK10
To enter the service mode TV include the
operating mode and briefly join the free output resistor R137 to the
hull. Resistor located on a plateau near the control buttons.
In the corners of the screen appear the letters F. Choose the appropriate option button remote control:
1 - a horizontal line;
2 - AGC (AGC);
3 - VCO (HRA);
4 - H POSI (horizontal alignment);
5 - L-STER , H-STER [R], H-STER [B], L-STER [R] - color shades;
6 - point in the center of the screen;
7 - the illumination of the screen one of the primary colors;
8 - CUT OFF (black level RG B);
9 - DRIVE (increasing R, G, B);
0 - brightness, contrast, tint, NTSC, sharpness, saturation;
VOL + - Auto Search;
DISPLAY - adjust brightness, saturation and contrast. Definition;
SLEEP - Auto Search;
0/AV - cubyarkost, subnasyschennost, subkontrastnost, subchetkost;
PREVIOUS - AFT (AFT);
VR541 - vertical size.
VR542 - centering vertically.
Parameter value change buttons L CH V.
[b]Adjusting the white balance to "white":
• Press the button on the remote control 9;
• Press 1 to adjust the amplitude of R;
• Press the 2 button to adjust the amplitude B.
Adjusting the buttons L CH V.
Adjusting the white balance to "black":
• Press the button 8
• Press 1 for adjusting the black level of R
• Press the 2 button to adjust the black level B
• Press the 3 button to adjust the black level of G
The parameters governing the buttons L CH V
Adjusting subyarkosti, saturation, contrast, sharpness, hue NTSC:
• pressing the 0 button several times, choosing the parameter;
• regulate the setting buttons L CH V.
To exit the service mode, press the button POWER.
Adjust settings are saved automatically.

Funai TV-2100A MK11 CPU LC863320A, videoprots. LA76810A
Log into the service mode: Close each pin. 2 and 16 RC
Valid for chips or remote SD7461GO RT2461-103

Funai TV-2100A MK12 Processor L11PAL 2ND M372CH8-056FP
In remote assembled on a chip 67N705 close third with the second (ground) terminal.
In the native RC is designated as the jumper J1. Login - SLEEP. Exit - STBY.
Work: Picture (bre, cnt, clr, tnt) VOL - switch other settings
buttons .. 2.3 6.8.9. At certain positions VOL - button work 1.2.3.
Adjusting the values ​​of buttons CH + \ -

GRAETZ
Turn the switch to digital module 'TV Internal Service Program' (SE on display).

GRUNDIG M63-105 ST63-160, ST63-781, E63-911. Processor MC68HC11F1. Chassis CUC1822/1823/1852
Starting
the internal memory of the processor. Shorted to ground (earth) pin 1
processor (contact MP2) and turn on the TV to the network. Click (i) on
the remote control (TP760). With the help of (P +) and (P) to select
SERVICE. Press (OK), enter the code ( (5) (0) (0)

GRUNDIG ST82775, ST95775, Processor SC415008FN4. Chassis CUC7880/7890
Push (i) will INFO CENTER. SPECIAL FUNCTION to select and click OK. Enter the code ( (5) (0) (0).

GRUNDIG M55-.., M63-.., ST63-.., ST70-.. Processor SDA2056/20562. Chassis CUC5360/5361/5510/551.
Click on the button (P / C) on the remote control to include a network switch. Exit - POWER OFF.

GRUNDIG ST55-725 ST55-750 ST55-800 ST55-95. Processor ZC411867P (MC68HC05T3). Chassis CUC2075, CUC7350.
Hold down the (i) to enable remote power switch.

GRUNDIG P37 .. P40 .. P42 .. P45 .. P50 .. T5 .. T55 .. Processor ZC88642P/88644P/42470. Chassis CUC6300.
Hold down the (i) to enable remote power switch.

GRUNDIG BOSTON ST270/8/IDTV/LOG. Chassis CUC1825, CUC1826.
Press the key (i) on the TV and click (OK) on the remote. Remember the value of (QA).

GRUNDIG GV200VPS. Processor SDA2087N.
On the remote press (CODE), then (4) (9) (3) (4). Confirm (OK) and press (STANDBY).

GRUNDIG M70-100, M70-580, M82-100, M95-100, M70-681. Processor SDA30161. Chassis CUC1835, CUC1860, CUC1880, CUC1890
Click
(i) on the remote. Use the (P) to cause the regime SERVICE DEMO press
(OK) (AUX). Call SERVICE MODE (OK) ( (5) (0) (0). Unlock: (VIDEOTEXT)
(PAGE) (CANSEL) (PAGE) (OK). Something to remember adjustment in service
mode to 7yu SDA3526 foot planted on the ground.

GRUNDIG M70-290 / 9 M84-211 / 8. CPU SDA5250-100. Chassis CUC1836, CUC1929.
Click
(i) on the remote. Use the (P) to cause the regime to press DIALOG
CENTER (OC). Call For authories dealer (OK) ( (5) (0) (0). Exit -
POWER OFF.

GRUNDIG P37/40/50 T51/55/65. Chassis CUC5301
Close legs processor RC MC144105 findings 6 and 10.

GRUNDIG P37-065/070/730. Processor ZC88667P ZC411718P SDA5222. Chassis CUC7300, CUC7301, CUC7303
Hold down the (i) to enable remote power switch.

GOLDSTAR CF-25 \ 29C44 chassis MC-51A
Click the OK button for a long time on the board Control board and the yellow button on the remote.

GOLDSTAR CF-25, CF-29, C26, C36, C76 chassis MC-51B
Simultaneously
press (MENU) (- VOL) ​​(- PR) Panel (OK)-store changes. To go to the
adjustment of white: = i - for GGB =? - For RGb = h - for BG.
Choose
option buttons L (CH) V. Change the value of buttons + (VOL) -.
Parameters recorded in the memory is automatically output - POWER OFF

GOLDSTAR Model CTK-4745. Programming produced by domestic remote PC-4

GOLDSTAR Model CB25C20X Processor GS831001A (SDA20160) Chassis
PC33B. Log in with a special remote control. Press and hold (SVC).
Console is built on a chip SAA3010. Close pins 1 and 11.

HITACHI CP2893TAN, CL2995TAN, CL28500TAN. Processor M37270MF. Chassis A5WK.
Hold down the button on TV (VOL +) and (VOL-) and turn the power switch. POWER OFF.

HITACHI CS2840TA. Processor NES3-..., NES2-... Chassis EUROSTE REO-2
(-/--) (MENU) (TV) - 1 sec. Exit - POWER OFF.

HITACHI C25 \ 28P445VT, C21 \ 1925 \ 28P745VT, C28P405VT. Processor CCU-SALO-09 (CCU20XX). Chassis DIGIT2000.
(P) (*) (O / V) (#) (M). Exit - (TV).

HITACHI 43FDX, 53FDX.
Open the front panel (four screws, two on each side). Remove the center
panel (six screws). Press the blue button in the left corner of the
board set. Exit - Press the blue button again

HITACHI C2578FS, C2589FS, CMT2578. Chassis V1
At the front of the TV, press (TV \ AV) and holding it turn on the TV.
After completing all adjustments, press the ENTER button on the remote
control (remembering), then the MENU button or turn the TV off.


[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
HITACHI C2135MN
Turn on the TV's front panel while holding the (-) button.

HITACHI C2160FS Z90234-4481 processor, videoprots. TDA8842
Log-in service: turn on the TV power switch holding the TV \ VIDEO on the front.


ITT 359, 387, 8F HIFI, CB5373Z, 6578F. Processor CCU SEL04/SEL07A
Mode 1: Press the screwdriver, the contact in the hole about the keypad and press the right button (S)
Mode 2: Press the screwdriver, the contact in the hole about the keypad
and press the right button (S) and re-click on the contact. Exit -
(LOAD).

ITT Processors: SAA1293-03-03 SAA1293A
On the keypad on the TV horizon without graphics click "SERVICE", the indicator will show
CH, press it paz - there will be OP, on volume select number of registers
(1-4) and figures (1-9) to change bits. After you press the 'Memory'. (You can also close the
conclusions of 15 and 23 SAA1250 chip in the console). Exit - POWER OFF.


JVC AV-29PRO
Set the volume control 04, and then successively press on the remote (DISPLAY) (MENU).

JVC C-21ZE, AV-G140T, AV-210T, AV-14ME, AV-14TE, AV-21TE/TE, AVG21T, AV-G250MX, 21A4EE, 21F4EE. Chassis MZ2, CA2
Simultaneously press the Control (DISPLAY) and (PICTURE MODE). (OFF TIMER) - remember.
Processors: M37102M8-C41SP. Menu is displayed as in Figure 1.

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
1. VCM PRESET change the preset brightness contrast and clarity.
2. SUB VSM switching color standards.
3. IF V \ C to change the settings correct screen mode and RGB matrices.
Next, you must again press the key combination and DISPLAY PICTURE MODE to display
screen system constants. The screen image will appear as in Figure 2.
Key PICTUPE ADJUST selects the position and the key PICTUPE ADJUST + / - changes
value. For storing settings, click the button OFF TIMER. To return
to the normal screen twice, press MUTE.

JVC A32020
Set (SLEEP TIMER) to 0 MIN, and so far is displayed on-screen information, press (DISPLAY) + (AV)

JVC AV-29TH3ER
On the remote control at the same time (MUTE) and (INFORMATION).

JVC AV-25TS2EK. Processor M37204MCC40SP. Chassis JE.
(I) (MUTE). Exit - (TV).

JVC AV-25VM1EN, AV-28VM1EN. Chassis JC.
(DISPLAY) (CINEMA / GAME). Exit - (DISPLAY).

LG MC64, MC84, SF-20/21, F60, CF-20/21, F80, CF-14/20/21, K40E, CF-14/20/21 K50/E/X, CF-14/20 / 21 K52E / X,
CF-14/16/20/21 S10EX, CF-14/16/20/21 S12E Chassis - MC64, MC84, MC84A.
Log into the service menu: Simultaneously press OK on the remote control and on the TV.

LG KF-14/20V30, KF-14/20/21U30/40, TVCR-060898 Use a regular
remote control, if removed from his upper lid, then you will see 4
groups of contacts for the 4 buttons, but not in the top cover under
these buttons holes and keys. Second from the left button is used to
enter the service mode.

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
LORENZ. Models: 359, 387, 8F, HIFI, CB5373Z, 6578F. Processor CCU SEL04/SEL07A.
Mode 1: Press the screwdriver, the contact in the hole about the keypad and press the right button (S)
Mode 2: Press the screwdriver, the contact in the hole about the keypad
and press the right button (S) and re-click on the contact. Exit -
(LOAD)

LORENZ. Processors: SAA1293-2003, SAA1293A-03.
C remote from TV "Horizon" without graphics click "SERVICE",
indekatore displayed on CH, Press again - there will be OP, on volume
choose the number of registers (1-4) and figures (1-9) to change bits. After the press
"Memory" (you can just close the conclusions of 15 and 23 IC SAA1250
in the control) Exit - POWER OFF

LIFETEC Model LT7000, STV6708, CTV2781. Processor ST6365.
Simultaneously pressing the red and blue buttons on the remote control.
Immediately thereafter, simultaneously press the (P-) and (VOL-). Exit -
(TV)

LOEWE. Model, ART500, ART630, ART700. Chassis - C9002S.
Hold the button (SERVICE) on the TV press on the remote control (CM). Exit - (TV)

LOEWE. Model 9000. Processor CUC2070. Chassis - DIGIT2000.
Press the service button on the motherboard around the CPU (pins 22 and 39) and click (CM) on the remote.

LOEWE. Model 7000. Chassis - S9003.
Five times to press the cursor right on the TV and just press the button (MEN) on the remote.

LOEWE . Chassis - Q2200.
Select 'SERVICE' in the menu, and then quickly press the 'MENU' button
on the remote. Choice: the yellow cells. Setting: + / -. Remembering:
'X'. Output: 'TV'.

LUXOR 5585-21A1, 7057-27, 63/7954 Chassis - "STEREO PLUS".
Log in Service: MUTE -> OK (M) -> TV Remember: OK (M). Exit: TV.

MITSUBISHI CT-21M5E \ ET \ RT, CT-25M5E \ EN \ ET \ ETN \ RT \ RTN:
Login: Hazhat on sepvisny pepeklyuchatel S701 (Close to tyunepom), then knopky 9 (in the limits of 5s).
"*" - Pepeklyuchenie pegylipovochnogo monitor displays, "2" - 8 "- pegylipovka code" 6 "-" 4 "- pegylipovka data" 0 "-
write to the memory, "1" Undo changes to records in memory. Output:
stand by. Button TV / AV - Exit from those. menu.
TUN 1 (0) - bands UHF, VHF
HTL 1 (0) - Disable the button "INSTALL"
TXT 0 (1,2) - 1 - Teletext incl. 2 - off
MNP - press "*" - entry in the settings menu
AVI 0 (1,2) - inputs AV: 1,2 - is
SYS 0 (1,2,3) - standard color (it should be SYS 1 or SYS 2)
STD 0 (1,2,3,4,5) - Standard audio (must STD 3)
Button TV / AV - Exit from those. menu.

MITSUBISI CT-29B3EEST
Log into the service menu:
Turn on the power. Small screwdriver, press on the micro switch S701, located
next to the slot antenna. And then on the remote 9 button for 5 seconds. Record
- Button 4. Buttons 2 and 0 to change the code control buttons 5 and 7, change the value
data.

MITSUBISHI Model: CT-29B3EEST, CT-29B2EEST, CT-21M5E/ET/RT, CT-25M5E, CT-25M5G.
Processors: CXP80424, ST9291N6B1NO/B10, ST9291N6B1ECS/B20.
Chassis: EURO-11, EE-3, EE-4
Powering up. A small screwdriver to press the mikrik S701, located near
with an antenna jack, and then - on the remote button "9" for 5 seconds.
Exit - (CM) POWER OFF

MAGNAVOX. Chassis - SOME.
To access the menu with the remote, press the following combination (0), (6), (2), (5), (9), (6). The channels are
change. Then press (MENU). To save your changes, press POWER on the TV.

MEDION SEG. Stamps - CT8050, CT8100, MD7103. Chassis - 11AK18.
Log into the service mode by pressing (MENU) + (1) + (6) + (7) + (5). Exit - (MENU)

NOKIA 6364, 7364 CHASSIS 2B-F:
Click on the button to turn the console - \ - -> MENU -> TV last button hold
within 1 second. Output from the service button to turn off the console.

NOKIA, SELECO, SABBA ITT, TELEFUNKEN (Chassis
STEREO PLUS)
Input: 1. (Mute); 2. (OK); 3. (Tv); record pezyltata "OK"
Exit: TV

NOKIA Model SAT1700.
(STORE ),(-/--),( TV / SAT)

NOKIA Model 8003.
(OK), (MUTE), (TV / SAT)

NOKIA Model: 3725CW, 4525CW, 5125CW. Processor - ST6367.
Pushing quickly (MUTE) (OK) (TV). Output - TV

NOKIA Models 61971, 6197, 6197DPL, 7282, 7295, 7296, 8296. Processor - SDA30C163.
Turn on the TV power switch in the lodge for 5 seconds command with the remote control (MENU) (TV) (i).
Exit from the menu - POWER OFF

NOKIA. Models: 6384, 6394, 7184, 7194. Processor CCU3000. Chassis - EURODIGI.
Initialize memory: Turn on the TV and just type a command from the control (MUTE) (TV).
Exit - POWER OFF

ORION 28BDF TV790 Processor SAA 5297PS/262.
Turn on the power button while holding down the MENU button on the front
panel, until the LED. Next, turn to the STBY button remote control.
Yield: menu OFF

ORION TV2180MK6 Processor OEC6027A (TMP87CH37N3194-9901H)
At the front of the TV, press and hold down the "VOLUME <" to "0", then hold, press the remote button "9".
The service menu consists of two sub-menus.

• 
  First:
  
  
  1. CUT OFF
     
  2. AGC
     
  3. V. SIZE
     
  4. BRIGHT
     
  5. COLOUR
     
  6. TINT
     
  7. END
     
  
  


• Second:
  
  
  1. AUTO
     
  2. SUB BRIGHT AUTO
     
  3. VCO AUTO
     
  4. AFT AUTO
     
  5. VCO
     
  6. AFT
     
  7. CONTRAST
     
  8. END
     

Selecting items in the submenu by pressing the appropriate "license"
keys on the keypad. Adjustment parameters are the keys "VOL "
or "- SET +" button on the RC.
The yield of the items in a submenu, as well as the transition from one
submenu to another made the same combination: "VOLUME <" to "0",
holding it press on the remote control key "9".
All values ​​are stored automatically.
Exit the service menu is by selecting "8" in any menu or by pressing the
"POWER".

ORION T2157/67/97, ​​T2567/97, ​​T2967/97 CPU LC863328A (5W63)

1. In the "STAND BY" press "RECALL" button on the RC
   
2. Pressing the "VOLUME <" on the front of TV set the volume level to "0"
   
3. Hold down the "VOLUME <", repeatedly press the "RECALL" button on the RC
   

Note: At default, paragraph 1 - the entrance to service the fifth attempt
The service menu is composed of four sub-menus:

• FACTORY (training)
  
• B / W (WB)
  
• ADJUST (control)
  
• SETUP (setup system constants)
  

Selecting a submenu by pressing the "RECALL" on the remote.
Note: At default, paragraph 1 - to select the fifth menu by pressing the "RECALL" button on the RC
Access to adjusting the parameters of the keys "VOLUME ".
Selection and adjustment of parameters, the keys "P + / P -" and "VOLUME
".
All values ​​are stored automatically.
Exit the service menu - pressing the "POWER"

PANASONIC TX-29GF35T, TX-33GF85T, TX-29GF85T chassis M18
Optional test is included if you press both
OFF TIMER button on the remote button and VOLUME-(minus) on the front of the TV.
Setting memory chips after e | replacement. Jumper TRA4 (contact
3 IC1213) and the TV (by mass). Then turn on the TV's power.
Apparatus clicking | m mode Market Mode. After the operation the jumper should be removed.

PANASONIC TC-24WG12H, TC-28WG12H GAOO Chassis M17W
Optional test is included if you press the button simultaneously OFF TIMER
button on the remote and VOLUME-(minus) on the front of the TV. Configuring Products
memory after e | replacement. Jumper TRA14 (pin 3 IC1213) and the body
TV (mass). Then turn on the TV's power. Apparatus clicking | m mode
Market Mode. After the operation the jumper should be removed.

PANASONIC TC-21E1R To enter the service
mode you must click on the main board of TV service button S1101.
Appears SNK. After the first nahatiya can adjust the basic (control
Brightness, Contrast, saturation, volume and phase (horizontal alignment)).
A second press of the button allows you to adjust modes tsvitnost RGB. FUNC -
change of the controlled object, NORM output.

PANASONIC TC-29V50R CHASSIS MX-2A
Tuning mode: Press the service switch S1101 (located near
alignment with the switch) TV switches to check on the screen
appears SNK. Click S1103 (FUN) to select the desired adjustment,
To exit, press S1101.

PANASONIC TC14S1RCP, TX14S1TCC, TC21S1RCP, TX21S1TCC, TX21S1TCP CHASSIS Z5
This chassis has the ability to self-test. To call the regime of self-testing
need to press buttons simultaneously OFF Timer button on the remote and VOL (-) on
the TV. After which the TV will go down in the process of self-testing and
will give on-screen message which is shown in Figure 1

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
What is the significance of these data. 1 (+) test EEROM (IC1205) plus indicates that
okay, 2 (+) Verify the microprocessor teletext, 3 (+) Check the tuner.
Attention TV model without teletext show option 2 (-).
Next, you need to make the installation options.
1.Set color saturation and sharpness to the minimum
2. Press the OFF Timer button on the remote control and the F key on the TV. Will
picture as in Figure 2

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
3. Select the desired option UP / DOWN keys on the remote.
4. Select the decimal value of the buttons 0-7.
5. Click on STR to store the changes.
6. To exit the TEST mode, press F.

PANASONIC CHASSIS MX3, MX-3C
Simultaneously press the RECALL button on the remote and-VOL on the TV. Output 2 times click on
remote button NORMAL.

PANASONIC TX-21AD2C, TX-29A3C, TX-25A3C CHASSIS EURO-2, EURO-1
Set the BASS control of the lower audio frequencies at a maximum, TREBLE knob treble
at a minimum. Press F on the TV at the same time with a button REVEAL
on the remote.

PANASONIC GAOO70 TX2170T
To enter the service menu you must click on the television V-(volume down) and hold
it pressed click the button on the remote which izabrazhen ekranchik plus. For
exit the menu should go to the submenu. Tam in the upper right corner is written in yellow and CHK nazhat N.

PHILIPS 14PT-1342 / 43, 14PT-1352 \ 00 \ 01 \ 05 \ 07 \ 11 \ 39
14PT-1542 \ 01 \ 43, 14PT-1552 \ 00 \ 01 \ 05 \ 11, 20PT-1342 / 43, 20PT-1542 / 43, 21PT-1532 \ 58,
21PT-1542 \ 43, 37TA-1232 \ 03, 37TA1432 \ 03, 37TA1462 \ 18, 37TA1473 \ 18, 52TB-2452 \ 19,
M-2052 \ 00 \ 01, M2152 \ 00 \ 07 \ 15, M2182 \ 00, M2192 \ 05 CHASSIS L6, 1 AA
There are 2 ways to enter the service.
1.Zakorotit contacts S1 S2 on the processor (pin 14 IC7600)
2.C using the service console model RC7150 pressing the mute button DEFAULT or ALIGN.
Output from the service click on the button STAN-BY.

PHILIPS 25PT8303
Log odnovpemenno press "?" and "sleep" under kpyshkoy.

PHILIPS Anubis S \ DD.
Log in to the service mode by contact closure, M31 and M32 (land) near IC7710. Exit STAN-BY.

PHILIPS 14PT-118A \ 50B \ 67R \ 94R, 14PT132A \ 50B \ 50R \ 75R,
14PT133A \ 162R, 14PT137A \ 162R, 14PT138A \ 54R \ 58T \ 67R \ 71R \ 74R \ 75R \ 93S, 20PT188A \ 50B \ 67R \ 73R,
20PT120A \ 78R, 20PT132A \ 75R, 20PT137A \ 62R, 20PT138A \ 50D \ 58R \ 58H \ 58R \ 67R \ 71R \ 73R \ 74R \ 75R \ 94R \ 97R.
CHASSIS L7, 1A \ AA
Short-circuit contacts M24 and M25 on the circuit board (PCB). Output from the service click on the button STAN-BY.
Attention buffer error is cleared!

PHILIPS 21PT440B, 21PT441B/02B, 21PT442B, 21PT4303,
21PT4422, 24PW6302, 24PW6322, 25PT5403, 25PT45, 25PT4523, 25PT5302, 25PT5322,
25PT5403, 25PT5423, 25PT6322, 25PT4503, 52TA4311. CHASSIS MD1.2/AA / Processors
TMP87CM36, TMP87CM38N
To enter the service mode is used panel type RC7150. With this panel TV can be translated
in two modes. 1 service is the default mode SDM (button DEFAULT). In regime
default, you can also enter through the contact closure S42 S43 on SSP (Panel
Small signal). To exit, press the button (Stand-by) (buffer error
cleared). 2 service adjustment mode SAM. Log in SAM mode is carried out
by sending commands ALING simultaneous pressing (MENU) and (-). After
enter the menu you will see a picture like Figure 1.

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
To exit, use the button (Stand-by) for errors can be monitored by
LEDs on the front of the TV. The list of error codes in the table.

Error CodeError DescriptionCount - in the blinkFaulty component

0	No Error	---------	----------------------
1	Error BIMOS (TDA8366)	1	IC7119 (SSP)
2	Error MSP3400/3410	2	IC7353 (SSP)
3	I2C bus error	3	All components on the I2C bus
4	Not the Rom (EEROM)	4	IC7685 (SSP)
5	Defective ROM (EEROM)	5	IC7685 (SSP)
6	Error Tuner	6	U1000 (SSP)
7	Error Teletext TXT	7	IC7702 (SSP)
8	CPU error Histogram	8	IC7210 (reserve)
9	CPU error 16:9	9	IC7440 (module 16:9)
10	Error module WSSB	10	IC7540 (module WSSB)
11	Error processing Dolby	11	IC7600 (audio module)

PHILIPS 25PT400/42, 25PT410A/42, 28PT400A/42, 28PT450A/42 CHASSIS GR2.2AA. Processor TMP47C1637
Log in servistny mode as follows. Zamyknite contacts M33 and M34 (service), and pressing
INSTALL on letsivoy panel enable the network pareklyuchatel. The screen should appear
Post SER. To exit the service please click on the button STANDBY.
Also in these models is servistnoe menu. Activated by pressing
VOL +, and then ETOGES time by pressing P +. In the second variant values
stored immediately. Go to the hotel mode as follows.
Turn on the TV for 38 channel while nazhamite keys VOL-, P-front
the TV.

PACE PRIMA Model: MSS100, MSS200, MSS500
Log into the service menu - (MENU), (0), (STORE), (RIGHT ANOW), (LEFT ANOW)

PRINCETON Model - AR2.7T
Log in - holding the button (+ VOL) ​​switch on / off switch

PROELCO Models: TAP2131, TAP2531, TAP2831 Processor 82C52.
Close the control points TR501. Hold (R +) (P) include
power switch.
Exit from the menu - remove the jumper TR501.

PROELCO processor-based SDA20563-A508/A516/A518.
Close the output processor 21 to ground. Click on the TV (P +) and (P) and include a network switch.
Exit - POWER OFF

PROSONIC Model CTV7289DVT Processor - SAA5296. Chassis - 11AK16
Log - (MENU) (3) (2) (9) (7)
Exit - (TV)

SABA Model - 21MG77C Processor - ST9291 Chassis - TX-90, TX-91, TX-92

1. On the keypad press (STAND BY)
   
2. Turn off the TV power switch
   
3. Hold the button on the remote control teletext (blue) - turn the power switch.
   
4. After turning on the TV, let teletext.
   
5. If you do not work, then in paragraph 4 of the button and release again quickly, briefly press.
   
6. Output from the service - POWER OFF
   

SABA Models: 28DT178ME, 28WS78KE/M/MP, 28DH78K, 28DU78K,
28DU88M/NE, 28DU98MP, 32VT88NP, 37WS88ME. Chassis - ICC19.
To access the menu to hold down the button (PR-) and (VOL-) on the front panel
TV turn on the power switch.

SABA Models: 52RW64E, 44W65ES, 52RW65ES, 52RW77WS
Turn on the TV while holding the button (PROG-) and (VOL-)

SABA processor ST9093. Chassis - ICC9.
Turn on the TV holding the blue button on the remote. Hold 5 seconds. Exit - POWER OFF

SABA Processor ST90R91 Chassis - ICC10
Method 1: Turn on the TV holding the blue button on the remote for 5 seconds.
Method 2: Turn on the TV holding the button (PROG-) and (VOL-). Hold button
8 sec.
Exit from the menu - POWER OFF

SALORA 6390, 7190, MV4000, PL14, 24101 852 SAT SOLI, 882 SAT SOLI, 885 SAT SOLI processor CCU-SALO-07 (CCU20XX), M1 chassis
(C) (*) (O / V) (#) (M), Output - (!)

SALORA 5575SFN, 28T7, processor ST92T93, chassis STEREO PLUS

(I) (M) (P)
Exit - (TV)

SALORA DIGIVISION 63 .. 2 71 .. 2, 2, .. N6 Processor NES3-... NES2-.., chassis EUROSTE REO-1
(-/--) (MENU) (TV) - 1 sec.

SALORA Processors TVPO2065-DO1, TVPO2066-A24
Close contacts 15 and 23 SAA1250 in remote or close contacts 14 and 19
in the SAA1250 RC. If not immediately included in the menu, you will
need an additional close contacts 11 and 21 in the SAA1250 RC.
Exit - (AV)

SAMSUNG(Candy bar) CHASSIS: SCV11A, B Model TVP3350, TVP5050, TVP5350
Login: StandBy -> P. Std -> Menu -> Sleep -> Power On
After logging into the service mode the on-screen menu appears: Adjustment, Option byte, Reset.
Abbreviations used in the mode of Adjustment: AGC - Auto Gain Control, SBT -
Sub Bright, SCT - Sub Contrast, SCR - Sub Color, STT - Sub Tint, PDL - Pal Delay,
NDL - NTSC Delay, RC - Red Cutoff, GC - Green, Cutoff, BC - Blue Cutoff, RG
- Red-Green drive gain, BG - Blue-Green drive gain, PSL - PAL vertical SLope,
PVS - PAL Vertical Shift, PVA - PAL Vertical Amplitude, PHS - PAL Horizontal
Shift, NSL - NTSC vertical SLope, NVS - NTSC Vertical Shift, NVA - NTSC Vertical
Amplitude, NHS - NTSC Horizontal Shift.

OPTION

BIT	ITEM	0	1
7	TTX	NO TTX	TTX
6	TTX SYSTEM	LIST FIRST	FLOF FIRST
5	CONTRAST	90	100
4	TUNER QUANTTITY	1	2
3	TUNER KINDS	2889	0889
2	SYSTEM (L)	-	-
1	SYSTEM (D / K)	-	-
0	SYSTEM (I)	-	-

OPTION 2

BIT	ITEM	0	1
7	NOT USED	-	-
6	NOT USED	-	-
5	POWER ON AFT	ONCE	TWICE
4	PDC	NO	YES
3	VPS	NO	YES
2	3.58 X-TAL	NO	YES
1	VIDEO PLUS	NO	YES
0	SHOWVIEW	NO	YES

VCR OPTION

BIT	ITEM	0	1
7	NOT USED	-	-
6	NOT USED	-	-
5	NOT USED	-	-
4	HEAD	2-HEAD	4-HEAD
3	SP / LP	SP-ONLY	SP / LP
2	SECAM	N / A	POSSIBLE
1	MESECAM	N / A	POSSIBLE
0	NTSC3.58	N / A	POSSIBLE

SAMSUNG CK5038 ZR \ TBWCX CHASSIS SCT11B
Press the following sequence of buttons on the remote: STAND-BY -> P. STD
-> HELP -> SLEEP -> POWER ON.
Exit from I STATUS.
Under the panel
console is a hidden button HIDDEN using this button, you can enter and
exit the menu.

SAMSUNG CS7272 PTR \ BWX CHASSIS SCT 51A
Enter the menu allows the following sequence of commands: PICTURE OFF ->
SLEEP -> P. STD -> MUTE -> PICTURE ON.

SAMSUNG CK6202 CK7202 CHASSIS SCT12B
Press the following sequence of buttons on the remote: STAND-BY -> P. STD
-> HELP -> SLEEP -> POWER ON.
Exit button or HIDDEN STATUS.

SAMSUNG CS-721, CS-723 CHASSIS SCT-52A
Alternately, press the button on the remote PICTURE OFF -> SLEEP -> P. STD -> MUTE -> PICTURE ON. Movement
cursor keys CHANNEL and VOLUME.

SAMSUNG CK 6271 WP
To enter the service
menu to 1. Hazhat button (HIDDEN) - hidden on the remote control 2. Hazhat very
rapid follow-up. (Stand-by) 3. (P.std) 4. (Help) 5. (Sleep) 6. (Power-on)

SAMSUNG CS 2139TR, CS21A0QWT, CK-564BVR, CZ-21H12T, CS-25M6HNQ, CS-21S4WR, CS-21S1S, CS-21D9 Chassis KS1A
(STAND-BY) (DISPLAY) (MENU) (MUTE) (POWER ON)

SAMSUNG CS-29A6HTR PLANO
(STAND BY) (DISPLAY) (P. STD) (MUTE) (POWER ON)

SANYO C21ML1 (MG) Processor: VESTEL 19V1.0NT
The entrance to the service. Push MENU (INSTALL), put cursor on "Configure".
Then click successively 4 => 7 = 2 => 5

SONOLOR Models: 5552, 6352, 6363, 6372, 6383, 7163, 7172, 7183, 63SN601. Processor NES3AR01/02, NES2-2R01/4R01
Login: (-/--) (MENU) (TV) - a combination of all the press for 1 second.

SONY KV-S2171K, KV-C2171KR, KV-X2101K, KV-X2501K, KV-X2581K, KV-X2581KR, KV-M2540K, KV-M2541K, KV-X2901K, KV-X2981K, KV-X2981KR Chassis BE-3B
In standby mode for up to 20 seconds on the remote control RM833 Repeatedly
Button: (Display on screen) (5) (VOL +) (TV). In the upper right corner will
inscription TT -.

SONY KV-M1440, KV-M2170, KV-M2171, KV-M2181, KV-M2101
Set the TV to standby mode. Next, you need to press a remote button in a sequence of ON SCREEN DISPLAY ->
5 -> VOLUME + -> TV. Data are given for the console type RM-836.

The number of flashes the LED	Value error
2	IC301ne confirms the transfer of 12C-volatile memory in order .
3	IC301neispravna flags.
4	No flyback horizontally.
5	IC301perepolnenie stack.
6	Fired Over Voltage Protection / current (pin 52)-high (1).
7	IC002ne confirms the transfer of I2C, IC301-right
8	IC002i IC301-no confirmation I2C.
9	Total oschibka I2C (SDAi SCLna low (0) IC301, IC001, IC002, CN001).

SONY KV-24WS1A/B/D/E/K/R/U CHASSIS BE-3B CXP85340A-116Q/117Q RM-837
Set the TV to standby mode. Next, you need to press a remote button in the sequence
ON SCREEN DISPLAY -> 5 -> VOLUME + -> TV.

Number of outbreaks LEDs	IC Type	Fatal error if
2....9	NVM (EEROM)	YES
10	TELETEXT	©
11	RGB / JUNGLE	YES
12	Switch AV TV.	©
13	PLLtyunera	YES

SONY KV-24WS2A/B/D/E/K/R/U CHASSIS BE-3D MSP3410B-PS-F7-T, MSP3410C-PS-C6-T RM-862
Set the TV to standby mode. Next, you need to press a remote button in a sequence of ON SCREEN DISPLAY ->
5 -> VOLUME + -> TV.

SONY KV25C1/A/D/B/E/R/K, KV29C1/A/B/D/C/K/R/E/D1 CHASSIS BE-3D RM-839
Set the TV to standby mode. Next, you need to press a remote button in a sequence of ON SCREEN DISPLAY -> 5 -> VOLUME +
-> TV.

SONY KV-2170, KV2180, KV2540 CHASSIS BE4
Set the TV into standby mode and press the button on the remote in the next
sequence ON SCREEN DISPLAY -> 5 -> VOLUME + -> TV.
Exit 00.

SONY KV2181KR SHASSIS BE-4
Set the TV to standby mode. Next, you need to press a remote button in the sequence
ON SCREEN DISPLAY -> 5 -> VOLUME + -> TV. Data are given for the console type RM-836.

Number outbreaks LEDs	Value Error
2	IC301ne confirms the transfer of 12C-volatile memory in order .
3	IC301neispravna flags.
4	No flyback horizontally.
5	IC301perepolnenie stack.
6	Fired Over Voltage Protection / current (pin 52)-high (1).
7	IC002ne confirms the transfer of I2C, IC301-right
8	IC002i IC301-no confirmation I2C.
9	Total oschibka I2C (SDAi SCLna low (0) IC301, IC001, IC002, CN001).

SONY KV-E2551A \ B \ E \ K, KV-S29 JN1 \ MN1 \ SN1, KV-S34 JN1 \ MN1 \ SN1 CHASSIS AE-2B
Use the remote type RM-831. Turn on the TV while pressing the button on any 2
front of the TV.

Number outbreaks LEDs	Type Products	Functional appointment
1	I2C bus	At SDAnizky level (0).
3	SDA3202	Tuner (PLL).
4	TDA9145	Chroma decoder.
5	CXA1587	RGB / Jungle.
6	TDA6612	Sound processor.
7	CXD2018Q	Scan vertically.
8	CXA1545	Switch AV / TV.
9	©	Protect scan vertically.

SONY KR-S4613 SHASSIS AP-2
Use the remote type RM-832. Turn on the TV while pressing any 2
button on the front of the TV.

Number outbreaks LEDs	Type Products	Functional appointment
1	I2C bus	Low level at SDA
2	X24C16	EEROM
3	SDA3202	PLLtyunera
4	TDA9145	Chroma decoder
5	CXA1587S	RGB / JUNGLE
6	TDA6612	Sound processor
7	CXD2018	Vertical Scan
8	CXA1545	Switch AV TV.
11	SDA5248	Teletext.
13	©	Sewn vertical sweep.

SONY KV-B2911/A/D/B/K, KV-B2912V, KV-B2913E CHASSIS AE-2
Use the remote type RM-830. Turn on the TV while pressing any 2 buttons on the front
the TV. In the upper right corner of the screen appears TT. After
then press MENU. Error can be opredilit the number of LED flashes
on the front of the TV. Process called self-diagnosis.

Number outbreaks LEDs	Type Products	Functional appointment
1	I2C bus	Low level at SDA
2	X24C16	EEROM
3	SDA3202	PLLtyunera
4	TDA9145	Chroma decoder
5	CXA1587S	RGB / JUNGLE
6	TDA6612	Sound processor
7	CXD2018	Vertical Scan
8	CXA1545	Switch AV TV.
11	SDA5248	Teletext.
13	©	Sewn vertical sweep.

SONY KV-T25MF1
Install the TV in standby mode with the remote then enter the following commands DISPLAY
-> 5 -> VOLUME + -> POWER. The sequence of operations in the mode of SERVIS
follows. 1i4 movement by position, 3i6 increasing and decreasing values
MUTING write 0 performance record. Applied remote RM-870

SONY KV-M2540
Set the TV into standby mode and press the button on the remote control in sequence ON
SCREEN DISPLAY -> 5 -> VOLUME + -> TV. Applied remote model RM-833

SONY KV-S29 RN1 \ 34RN1 SHASSIS G1
Entry into service mode by using the remote control RM-821. Turn on the TV in
standby mode. Then press the following combination of buttons on the remote: DISPLAY ->
5 -> VOL + -> POWER

SONY KV-S2941A \ B \ D \ K, KV-S2942U, KV-S2943E SHASSIS AE-2F RM-831
Turn on the TV, and then double-click on the button on to do. In the upper right corner appears on the TT, then press
click on MENU.

Number outbreaks LEDs	Type Products	Functional appointment
1	I2C bus	Low level at SDA
2	X24C16	EEROM
3	SDA3202	PLLtyunera
4	TDA9145	Chroma decoder
5	CXA1587S	RGB / JUNGLE
6	TDA6612	Sound processor
7	CXD2018	Vertical Scan
8	CXA1545	Switch AV TV.
11	SDA5248	Teletext.
13	©	Sewn vertical sweep.

SONY KV-B2911/A/D/B/K, KV-B2912V, KV-B2913E CHASSIS AE-2
Use the remote type RM-830. Turn on the TV while pressing any 2 buttons on the front
the TV. In the upper right corner of the screen appears TT. After
then press MENU. Error can be opredilit the number of LED flashes
on the front of the TV. Process called self-diagnosis.

Number outbreaks LEDs	Type Products	Functional appointment
1	I2C bus	Low level at SDA
2	X24C16	EEROM
3	SDA3202	PLLtyunera
4	TDA9145	Chroma decoder
5	CXA1587S	RGB / JUNGLE
6	TDA6612	Sound processor
7	CXD2018	Vertical Scan
8	CXA1545	Switch AV TV.
11	SDA5248	Teletext.
13	©	Sewn vertical sweep.

SONY KV-29X1A \ B \ D \ E \ K \ L \ R \ U CHASSIS BE-3D
Set the TV into standby mode and press the button on the remote in the next
sequence ON SCREEN DISPLAY -> 5 -> VOLUME + -> TV. Applied
Remote model RM-839.

Error	Number outbreaks LEDs
Protection circuit	2
Low signal SLCna I2C bus	3
Low signal SDAna I2C bus	4
Low signal SLCi SDA	5
Kontreller JUNGLE / CHROMAne answers	6
Video switch is not responding	7
Tuner does not respond	8
MSPne answers	9
NVMne answers	10
Low signal M3L TXD	11
Low signal M3L RDX	12
Low signal M3L ENABLE	13
Low signal M3L TXD and RXD	14
Damage to test Compact Text	15
Switch AVne reset when power is turned	16
Unable to initialize the jungle	17
Reply NVMpovrezhden after initialization	18
A few chips do not meet	19
Wrong time of the Compact Text	20
Response switch AVpovrezhden after answering	21
Reply controller JUNGLE / CHROMApovrezhden after the response	22
Compact Textne answers	23

SONY KV-29X1A \ B \ D \ E \ K \ L \ R \ U CHASSIS BE-5
Set the TV into standby mode and press
on the remote control in sequence ON SCREEN DISPLAY -> 5 -> VOLUME +
-> TV. Applied remote model RM-836.

The number of flashes the LED	Value Error
2	IC301ne confirms the transfer of 12C-volatile memory-to-right
3	IC301neispravna flags.
4	No flyback horizontally.
5	IC301perepolnenie stack.
6	Fired Over Voltage Protection / current (pin 52) high- level (1).
7	IC002ne confirms the transfer of I2C, IC301-right
8	IC002i IC301-no confirmation I2C.
9	Total oschibka I2C (SDAi SCLna low (0) IC301, IC001, IC002, CN001).

SONY KV-S2951 KR CHASSIS AE-3
Use the remote type RM-831. Turn on the TV while pressing the button
- And + on the front of the TV.

Number - in Meghann LEDs	Description	Fee
1	Common error I2C Bus	-
2	Error IC ST24C16	A
3	Error sub-controller CXP85332	A
4	Error video processor CXD2030R	B B 1
5	Failed to digital converter sampling CXD2032R	B B 1
6	Error converter review CXD2035R	B B 1
7	Error video controller TDA1839	A
8	Driver error CRT TDA1840	A
9	Failed to switch AV TV CXA1855	J
11	Error chip Megatext CDA5273	A
12	CPU error sound TDA6812	A
16	V-protectionzaschita voltage	-

SONY KV-16WT1 A \ K \ R \ U
Set the TV into standby mode and press the button on the remote in the following sequence
ON SCREEN DISPLAY -> 5 -> VOLUME + -> TV. Applied remote model RM-836.

The number of flashes the LED	Value Error
2	IC301ne confirms the transfer of 12C-volatile memory in order .
3	IC301neispravna flags.
4	No flyback horizontally.
5	IC301perepolnenie stack.
6	Fired Over Voltage Protection / current (pin 52)-high (1).
7	IC002ne confirms the transfer of I2C, IC301-right
8	IC002i IC301-no confirmation I2C.
9	Total oschibka I2C (SDAi SCLna low (0) IC301, IC001, IC002, CN001).

SONY KV-C2173 B / E, KV-C2171 D / K / KR CHASSIS BE-3B:
Set the TV into standby mode and press the button on the remote in the next
sequence ON SCREEN DISPLAY -> 5 -> VOLUME + -> TV. Applied
Remote model RM-833.

Number outbreaks LEDs	Type Products	Fatal whether error
2....9	NVM (EEROM)	YES
10	TELETEXT	©
11	RGB / JUNGLE	YES
12	Switch AV TV.	©
13	PLLtyunera	YES

SONY KV-2501 A / D / K, KV-C2503 B / E, KV-C2508 D / E, KV-C2509 B / D / E / K.
Set the TV into standby mode and press
on the remote control in sequence ON SCREEN DISPLAY -> 5 -> VOLUME +
-> TV. Applied remote model RM-833.

Number outbreaks LEDs	Type Products	Fatal whether error
2....9	NVM (EEROM)	YES
10	TELETEXT	©
11	RGB / JUNGLE	YES
12	Switch AV TV.	©
13	PLLtyunera	YES

SONY KV-G21M1 \ G21P1 \ G21S11, KV-T21M1 \ T21MF1 \ T21MN1 \ T21MN11
Method of exit from the service: Press 2 times the button POWER. Recording method
in memory: Log in to press service combination of buttons on the remote one (UP) 4 (DOWN) will choose
adjustable parameters. Press the MUTE button to call the screen WRITE (green), press
0 key to enter into memory.

SONY KV-21T10R
Set the TV into standby mode and press the button on the remote control in sequence ON SCREEN DISPLAY
-> 5 -> VOLUME + -> TV.

SONY KV-21C4B/D/E/K/R KV-21X4A/B/D/E/K/L/R/U CHASSIS BE-5 CPU SDA5255-A024. Remote RM-836.
Set the TV into standby mode and press the button on the remote in the next
sequence ON SCREEN DISPLAY -> 5 -> VOLUME + -> TV.

Number outbreaks LEDs	Code Error	Description
2	30	Controller chip Junglene confirms the transfer of high level I2C bus
3	31	Error flag controller chip Jungle
4	32	No signal reversal in the horizontal
5	40	Sound processor does not support the transmission of high-level I2C bus
6	91	No vertical sync
7	10	Nonvolatile memory NVMne confirms the transfer of low- level I2C bus
8	20	The tuner does not confirm the transfer of high-level I2C bus
9	01	Error general I2C Bus
10	90	Input protection: protection of the X-ray (X-rays).

SONY KV29F3A/B/D/E/K/R/U CHASSIC BE-3D Processor SDA302C263-GEG Remote RM-862
Set the TV into standby mode and press the button on the remote in the following sequence
ON SCREEN DISPLAY -> 5 -> VOLUME + -> TV.

Error	Number outbreaks LEDs
Protection circuit	2
Low signal SLCna I2C bus	3
Low signal SDAna I2C bus	4
Low signal SLCi SDA	5
Kontreller JUNGLE / CHROMA not responding	6
Video switch is not responding	7
Tuner does not respond	8
MSP does not meet the	9
NVM is not responsible	10
Low signal M3L TXD	11
Low signal M3L RDX	12
Low signal M3L ENABLE	13
Low signal M3L TXD and RXD	14
Damage to test Compact Text	15
Switch AVne reset when power is turned	16
Unable to initialize the jungle	17
Reply NVMpovrezhden after initialization	18
A few chips do not meet	19
Wrong time of the Compact Text	20
Response switch AVpovrezhden after answering	21
Reply controller JUNGLE / CHROMApovrezhden after the response	22
Compact Textne answers	23

SHARP 14 \ 21 JN1 CHASSIS SP-51
When the input of the microcontroller 37 for 3 adjacent periods in a state
High-level call service menu.

SHARP VT-1428M, VT-2128M
Set the TV into standby mode and press the button on the remote in the next
CH UP sequence for 2 seconds or more, and simultaneously press
button POWER. Exit the menu button MENU.

SHARP 54AT-15SC
To enter the service, press the following buttons in sequence to the console. POWER OFF and then simultaneously
VOL-and CH + on the TV. After that POWER ON and hold the VOL-and CH + until the TV will not start.

SHARP 14D-SC, 14B-SC, 20B-SC, 14D-CM, 21D-CK1, CV-2132CK1 CHASSIS PAL-A.
Set the switch S1008 to the position servistnogo regime.

SHARP 14R-SC/M8/M10, 14R-W, CV-14RU
Set the switch S1006 to the position servistnogo regime.

SHARP DV-5450SC CHASSIS S3B Processor IX1492BM, SDA-20561
To enter the service mode is necessary to block VIDEO
connect terminals (2) and (6). Then press the MODE button on the remote.
A message-SERV-. Then remove the jumper. The choice of adjustment of the CH and
CH +.

SHIVAKI CHASSIS 11AK19
To enter the sersisny mode, do the following manipulation. First enter the installation menu
INSTALL button and then press a key on the remote in the following sequence
4, 7, 2 and 5. Look for the menu position ADJUST (all adjustments are changed through it).

SHIVAKI STV1415 CHASSIS 11AK20
To enter the service menu must be made within 4 seconds to perform the login procedure. Must
press the remote control the following sequence of keys. (VOL-), (Prog), (-),
(TV). Options selected buttons (PROGRAM UP) (PROGRAM DOWN), and the change (VOL-),
(VOL +). To store, press the red button. To exit, use the button TV.

SHIVAKI STV2905 CHASSIS DY-900

1. Click on SERVICE remote.
   
2. In this case, the image appears OSD (onscreen display) "Line SVC". Then click on the button -/-- control.
   
3. At this time the load data recorded in the micro-channels of memory.
   
4. The downloaded data are as follows:
   

(1). STD	4CH	and	62,25 Mg
(2). STD	5CH	and	172,25 Mg
(3). STD	7CH	and	189,25 Mg
(4). STD	25CH	and	503,25 Mg
(5). STD	34CH	and	575,25 Mg
(6). STD	40CH	and	623,25 Mg
(7). STD	50CH	and	703,25 Mg

1. Color fixed channels OSD - Green.
   
2. To view the channels recorded in the memory press PR +, -.
   

Adjust V-SIZE (vertical size)

1. To receive a test table RETMA press the PR +, -.
   
2. To perform the adjustment, press "6" remote control, and the image appears OSD "STV VAMP32".
   
3. Clicking on knokli VOL +, - to adjust the vertical size. The remaining adjustment onalogichny.
   

SHIVAKI STV 2040 Chassis 11AK30-2 processor - ST92195C7B1/PAL VESTEL/T30F016, video processor - STV2248C
Log-in service: Press MENU, then press the sequence 4 => 7 = 2 => 5

SHIVAKI STV-2139 Processor - Z9023306PSC, video processor - TB1238BN
Log-in service: in the operating mode to click in sequence on the remote control: DISPLAY => MUTE => SLEEP => FUZZY
Mode selection menu: DISPLAY, SLEEP, MUTE.

THOMSON, TELEFUNKEN CHASSIS TX-90, TX-91
Put TV into standby mode with remote control. Then turn off the mains button. Press the teletext button on the remote (blue)
and holding to include a network switch. Then release the button Teletext dramatically and immediately click.

THOMSON a new generation.
With the power off press the side "V-" and "P-" deduct and include meals. Services menu appears.

THOMSON 21MG77C
THOMSON 21MG10E Processor: TDA9554PS/N1/0301
To access the menu, do the following

1. TV - in stand-by (standby mode) with the remote.
   
2. Turn off the TV network button.
   
3. Udepzhivaya teletext button on the remote, switch on the TV network button.
   
4. After turning on the LEDs in full REGIME - what have you got - green, lupus?), Release the button Teletext
   
5. If you do not spabotaet, all the same, only in part 4 teletext button again and release quickly to kpatkovpemenno press.
   

TOSHIBA 1450 XN \ XNE 1458XNH 2050XN 2150 XNE \ XHC \ XC CHASSIS S5E
Enabling self-control: When the screen displays the menu control, press
the 9 button on your remote. Begin the process of self-testing.

TOSHIBA 2150 (chassis - S5E)
Login:

1. mute
   
2. again press the MUTE and otpyskat
   
3. press the MENU button on the TV
   

"4" - correction were kontpasta. "1", "2", "3" - cutoff R, G, B "AV" - Choice of test
signal. "- gpomkost +" - pegylipovka.
Output: off - power.

TOSHIBA 2185XR
To enter the service menu to

1. Hazhat button on the remote control (MUTE)
   
2. More paz press (MUTE) and do not let it go
   
3. Hazhat on the TV button (Menu)
   

Each press of a button (CHANNEL
UP) changes the position pegulipovochnye Each press of a button (+ VOLUME) and (-VOLUME)
change data. Exit - Turn off the TV.

TOSHIBA
1.B regime: SERVICE click on the button box - line of horizontal
ON / OFF (kpuzhochek with stpelkoy). Each subsequent press changes kaptinku.
2. In the regime of the menu pegulipovok book. (9) entry in the menu self
SELF CHECK. ******** - Nome.p mikpoppotsessopa Power - 00 - diagnostics unit
supply. 00 - nopma if the numerals of one another in many shows paz spabatyvala system
protection - a tendency to current overload. Bus line - the verification of tire chains.
OK-nopma, SDA - GND - goat SDA bus on the lot, SCL - GND - similar bus SCL.
SDA-SCL - essno among themselves. Bus cont - the verification of tire components. OK - nopma.
Q *** NY - mikposhema with nome.p *** neisppavna. SYNC - sinhponizatsiya. OK - nopma.
NG - ppots. This function operates and attempts to define a type of video

UNIMOR Model - SIESTA-3/3A Processor SDA20562-A508/A515/A522.
Log into the service menu: Close the output 21 to ground. Click on the TV (P +) and (P) and include a network switch.
Exit from the menu - POWER OFF

WALTHAM Model - WT821
Log into the service menu - the TV remote control "Horizon" without graphics click (SERVICE),
indekatore displayed on CH, Press again - there will be PR on the volume selected number of registers (1-4)
and numbers (1-9) to change bits. After the press (Memory).

XANTRAX TC-2172S (chassis TD-18)
Video Processor: TD1238N
Control Processor: TMP87CK38N
There are three service modes: S, D, M.
S-Mode - the service;
D-mode - extended service;
M-mode - expedited + training.
Log in to the service S-mode control (SERVICE MODE) with a conventional
remote control: in the operating mode of the TV, press and hold
on the front panel button VOL-(volume at minimum position), press the
button on the remote DISPLAY. In the upper left corner of the screen
TV will be the symbol S is the inclusion of a special regime of service
regulation.
Selection of a new function by pressing the button on the remote control or PROG + PROG-.
Adjusting the value of the function by pressing the remote button VOL + or VOL-.
When pressed on the remote control button on the screen disappears -/--
Frame Scan. From the emission of a narrow horizontal band handle
accelerating voltage.
The values ​​of the controlled functions are stored in memory automatically.
Log in to service mode D, M possible only with a special service remote control.
TV returns to normal operation after turning off the network and then on again.

XANTRAX TC-1466, TC-2066S, TC-2166S, TC-2068S, TC-2168S, Chassis ST-208, 209
Video Processor: TDA8842
Control Processor: MTV212MS64U
Log in to the service adjustment mode (SERVICE MODE) with a conventional remote control:
in standby mode, press the TV series on the remote control button, MUTE, AV, MENU, POWER.
In the main user menu there is a new line - SERVICE.
To enter a basic service menu, press the remote button VOL +.
Reulirovka value of the function by pressing the remote button VOL + or VOL-.
Selection of a new function by pressing the button on the remote control P + or P-.
Schedule of Basic Tools:
SCREEN - Reg. Screen settings
CATHODE - Reg. Regimes cathodes
TUNING - choice of parameters of the tuner
SCR - subnasyschennost
OSD Pos. - Adjusts the OSD position horizontally
SCREEN, CATHODE, TUNING have their own sub-sub-menu.
The values ​​of
the controlled functions are stored in memory automatically. TV returns


ZENITH IQB64W10W
8-6-5-4-5-6-8
7-5-3-2-3-5-7
6-4-2-1-2-4-6
7-5-3-2-3-5-7
8-6-5-4-5-6-8
Gain from control of the codes and press (ENTER) or (DISPLAY)

ZENITH IQB64W10W
9-8-7-6
Gain from the control code and press (ENTER) or (DISPLAY)

to normal operation after turning off the network and then on again.

LG LCD MODEL 26LC2D CHASSIS MODEL LA63E

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذا الرابط]