أشرف عثمان للإلكترونيات
أهلا وسهلا بكم ونتمنى أن تستفيد معنا


schematic-VIDEO CASSETTE-monitor-service manual SHASSIS Panasonic Philips SAMSUNG SANYO SHARP SONY toshiba Aiwa AKAI DAEWOO Goldstar HYUNDAI VIDEO Grundig Hitachi JVC LG Mitsubishi National NEC ORION VESTEL Corus-Repair-Plasma-LCD
 
الرئيسيةالتسجيلدخول
https://twitter.com/ashraf69osman--- https://www.facebook.com/ashraf.osman.73-- https://plus.google.com/u/0/+ashraf5914

شاطر | 
 

  سرفس شامل أجهزة service-mode PHILIPS

استعرض الموضوع السابق استعرض الموضوع التالي اذهب الى الأسفل 
كاتب الموضوعرسالة
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: سرفس شامل أجهزة service-mode PHILIPS   الأربعاء يونيو 16, 2010 1:34 pm


سرفس شامل أجهزة
PHILIPS


TV Philips GR1-AX Chassis, HOTEL Mode
depends on the buttons. Subject already ran ....
GR1-AX Hotel mode
• Select a channel 38 on TV
• Simultaneously press the STORE, and PROGRAM + on the TV (the inclusion of hotel mode)
• Simultaneously press the STORE, and CONTROL + on the TV (turn off hotel mode)
GR1-AX Hotel mode
• Select a channel 38 on TV
• Simultaneously press STORE on the TV and the remote SLEEPTIMER for 4 seconds
GR1-AX hotel mode, TMP47C434N-3141
• No hotel mode
GR1-AX hotel mode, TMP47C434N-3142
• Select 38 for TV
• Simultaneously press the SELECT key on the TV and the remote SLEEPTIMER for 4 seconds
• Notes:

  • We introduce a volume limit for this mode
  • STORE or INSTALL, can not be entered
  • A green 'H +' appears in the left bottom of the screen when hotel mode is activated, which can
be removed by powering down the
TV and powering it up again

  • A green 'H-' appears in the left bottom of the screen when hotel mode is deactivated, which can
TV Philips GR1-AX Chassis, HOTEL Mode



depends on the buttons. Subject already ran ....
GR1-AX Hotel mode
• Select a channel 38 on TV
• Simultaneously press the STORE, and PROGRAM + on the TV (the inclusion of hotel mode)
• Simultaneously press the STORE, and CONTROL + on the TV (turn off hotel mode)
GR1-AX Hotel mode
• Select a channel 38 on TV
• Simultaneously press STORE on the TV and the remote SLEEPTIMER for 4 seconds
GR1-AX hotel mode, TMP47C434N-3141
• No hotel mode
GR1-AX hotel mode, TMP47C434N-3142
• Select 38 for TV
• Simultaneously press the SELECT key on the TV and the remote SLEEPTIMER for 4 seconds
• Notes:

  • We introduce a volume limit for this mode
  • STORE or INSTALL, can not be entered
  • A green 'H +' appears in the left bottom of the screen when hotel mode is activated, which can
be removed by powering down the
TV and powering it up again

  • A green 'H-' appears in the left bottom of the screen when hotel mode is deactivated, which can
be removed by powering down
TV and the inclusion of this again
GR1-AX hotel mode, TMP47C434N-3537
• There is no way the hotel
GR1-AX hotel mode, TMP47C434N-3414/3415, TMP47C634N-R494
• Select 38 for TV
• Simultaneously press the key STORE, and PROGRAM + on the remote for 4 seconds (the inclusion
Hotel Mode)
• Simultaneously press the STORE key and KEY CONTROL - on the remote for 4 seconds (OFF
Hotel Mode)
• Notes:

  • The maximum amount in the way the hotel will present the volume, activating it
  • SAVE or SET mode can not be introduced
  • The number of programs shown on the screen for 4 seconds

GR1-AX (8 buttons) method Hotels, TMP47C434N-R221
• Select program 38 on TV
• Simultaneously press Store and include television SLEEPTIMER on the remote for 4 seconds (the inclusion
Hotel Mode)
• Notes:

  • We introduce a volume limit for this mode
  • SAVE or SET mode can not be introduced
Or simply put a blank memory
PHILIPS CHASSIS 3A. 17CE7630, 21CE7649/55/7590, 17CE7531/7650 247 771, 41CE8746.

Press
(MONO) TV on the keyboard. Hold the switch on the TV with remote control. Exit: STAND-BY
Video recorder Philips 14PV111/01, 14PV112/01, 14PV203/01, 14PV415/01, 14PV460/01 Chassis TV-VCR
2002-14 "Range (Z11)
Log in to the service: Within 5 seconds press the STAND / BY, 2,7,1, MUTE, STAND / BY.
A7H.1
We have a bunch: 24w04 TV Philips 28PT4503/00
Fee SMALL SIGNAL "3111 258 17 542": TMP87CM36N-3422 M128A1-4.0 +
8.00 MHz, 24W04, TDA8366, TDA4665, (TDA8395), DATASLICER CF72416 +
13875kHz, CF70200FNW, TDA2545A, HEF4053BP
Sound module ITT 3111 253 3250 2 "4822 212 10 941 ITT NO NICAM":
MSP3400C-PP-C6 or MSP3410
Tuner: 3112 297 11 591 UV916S KR20
TDKS: 31 762
To enter the service, connect the S42 and S43
And press "MENU" and "-" on the TV at the same time.
NEED DUMP FOR TV PHILIPS 14HT3302/00
INSADE IS EEPROM 24C04
TMP 87CM36N-3438
HTV NS V 1.6 9738 EAI
TOSHIBA JAPAN
Subject: Re: [carradio-decode] TV PHILIPS 14HT3302/00
Date: 09 July, 2001 9:49
step 4 is: Select "off" with "contr + / -"
If not, select prog 38 and after 4 seconds press "control" and
"+" (Or "prog +")
> Log in to the service by simultaneously pressing the "VOL +" and "PR-".
> Select "OPTION 2" by pressing the green button.
> Select the "HOTEL" by pressing the yellow button.
> Select "ON" with "CONTR +/-".
> Leave Service Menu via standby.
> I NEED DUMP FOR TV PHILIPS 14HT3302/00
>> INSADE IS EEPROM 24C04
> >
>> TMP 87CM36N-3438
>> HTV NS V 1.6 9738 EAI
>> TOSHIBA JAPAN

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]


عدل سابقا من قبل أشرف عثمان في الخميس يوليو 21, 2011 8:42 am عدل 1 مرات
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس شامل أجهزة service-mode PHILIPS   الخميس يوليو 21, 2011 8:12 am

PHILIPS CHASSIS AA5. 17PT156B.
S1 and short out the conclusion to plant pins 7 processor
on the ground) and then turn on the network button. Caught in the mode of SDM. Then simultaneously press the
buttons (+)
and (-) on TV. . Exit: POWER OFF.
PHILIPS Anubis S \ DD.
Entering the service mode by closing
M31 and M32 contact (ground) near IC7710. Exit STAN-BY.
PHILIPS CHASSIS CTV-530.

Short the conclusions of 15 and 20 of the processor control. Exit: (TV).
PHILIPS CHASSIS D16-II. 25DC2660, 28DC2070, 28DC2670.

Service default mode:
Hold button
on TV (VOL +) and (P +) to include a network switch.
Service Mode: M30 short-circuit the control points and the M31. Exit: TV MODE.
PHILIPS CHASSIS E-6. 28PT-4505.
Plug in a working mode and dial in
remote control (TV) (I) (STOP) (TV) (I) (STOP). Exit: (STANBY).
PHILIPS Shassis EM2E 29 PT9007/58 ()
Log into the service menu: When
unit to the remote home quickly enter 062 596. In the lower right corner of the word DILER. Push (i +).
PHILIPS CHASSIS FL1.10. 25PV7505 25SL550, 33PT700A/712A.
1. SERVICE mode
DEFAULT MODE - closed point S24 S25, located on the board SSP. On the remote press (MENU) (Blue)
(Red) (MENU +) (MENU OFF)
2. To activate SERVICE MODE jumper control points S23 and S24 are located on the motherboard
SSP. Exit: STAND-BY
Service mode TV PHILIPS chassis L01.1E AA
TV chassis firms PHILIPS L01.1E AA has already been discussed in the pages of our magazine (see
"Repair & Service", № 10, 2004). Continuing the theme of service we offer to meet with the regime
this chassis and its master hardware and software adjustments.
TV sets, collected on the chassis L01.1E AA can be transferred to the following service options:
- Leveling service mode by default (SDAM);
- Client-service mode (SSM).
Service mode SDAM serves the following purposes:

  • creation of integrated systems of all nodes chassis for measurement and electrical configuration chassis;
  • blocking protection scheme;
  • start blinking LED procedure for fault diagnosis;
  • installation options;
  • display / clear the buffer error codes;
  • alignment settings.
Service mode adjustments for chassis SSM is not used and its options are read-only.
Service mode SDAM sets mode to the TV:
- On top of the screen displays the message "S";
- Frequency of receiving stations with the antenna input of 475.25 MHz;
- Color system is SECAM L for France or PAL-BG to other Western European countries;
- The volume set at 25% of the maximum value, other parameters of sound
and images - at 50%.
In the SDAM blocked following modes: sleep timer, parental lock, blue background, hotel
auto-shutdown (when no video signal IDENT for 15 minutes), skipping unwanted channels
Autosave preferences.
To enter the service mode SDAM on the main board close the chassis between a jumper and 9631 9641,
then include the TV switch. After the image appears on the screen (Fig. 1),
opens the connection between the bridges 9631 and 9641.
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig. 1. The image on the screen in SDAM
Note. It must be borne in mind that when the jumper is closed 9631 and 9641, off protection
Short-circuit 8 V.
Fig. One of the following symbols mean:
LLLL - counter hours of operation;
AAABCD XY - the software version number;
S - service mode indication SDAM;
ERR - error buffer that stores the last five error codes;
XXX - byte option;CLEAR - resets the buffer errors (to reset, select the row and click
cursor "right");
OPTIONS - sub set of bytes of options;
AKB - enable (1) or off (0) control scheme of dark current ray tube;
TUNER - Tuner Settings sub-menu;
WHITE TONE - white balance;
GEOMETRY - sub control image geometry;
AUDIO - adjust the audio submenu.
To navigate the service menu using the cursor buttons SDAM remote control "up / down."
The selected line becomes brighter. Activate the selected submenu (set value) is
by pressing cursor button remote control "to the left / right."
If in SDAM press MENU, you can go in the user menu (the usual menu options
parameters). To return to the SDAM press the OSD / STATUS on the remote. To return from a submenu in the
previous menu, press the MENU button on the remote.
To save settings, service mode, press the SDAM STANDBY button on the remote.
Consider the hardware and software control chassis L01.1E AA.Hardware control chassis L01.1E AA


عدل سابقا من قبل أشرف عثمان في الخميس يوليو 21, 2011 8:56 am عدل 1 مرات
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس شامل أجهزة service-mode PHILIPS   الخميس يوليو 21, 2011 8:14 am

Adjust the accelerating voltage Vg2
1. Activate the service mode and it SDAM selected sub WHITE TONE.
2. Set values ​​NORMAL RED, GREEN and BLUE is 40.
3. Using the MENU button returns the user menu and set the minimum contrast
and brightness (OSD image that was barely visible).
4. Returns to SDAM by pressing MENU.
5. Connected to the antenna input of the TV test signal generator and signal the "black box".
To control the adjustment connect an oscilloscope (1:10, 0.2 ms / div) to one of the cathode tube.
6. Variable resistor Screen (bottom to TDKS) set a constant voltage from zero
to the level of extinction (the horizontal blanking area row), equal to 160 ± 4 V
Adjustment of the focusing voltage
1. Connected to the antenna input of the TV test signal generator and signal "grid".
2. Press the SMART PICTURE on the remote control mode is selected the image or NATURAL MOVIES.3. Variable resistor Focus (top to TDKS) achieve an optimal focus over the entire area
screen.
Software control chassis L01.1E AA
These adjustments do in the service mode SDAM. These include:

  • installation of bytes of options (sub OPTIONS);
  • control the tuner (sub TUNER);
  • White Balance Adjustment (sub WHITE TONE);
  • adjust the geometry (sub GEOMETRY);
  • adjust audio track (sub AUDIO).
Set byte options
Enter the service mode and it SDAM select and activate row OPTIONS. You should
image to appear (Fig. 2).
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig. 2. The image on the screen in bytes of options
Altogether there are seven bytes of options OP1-OP7. Setting these bytes to configure
configuration of a specific model? tuner type, region, sound processor modes, possible
broadcasting system, preset and SMART PICTURE SMART SOUND, stereo / mono, etc. InTable. 1 shows the fixed values ​​of the bytes of options for different models of TVs.
Necessary byte values ​​of options set with the cursor keys "left / right" on the remote.
The new values ​​are stored after the previous menu.
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Adjusting the tuner
This adjustment is performed only after replacing the tuner chip nonvolatile memory 7602.
In service mode, activate the line SDAM TUNER. Submenu appears on the screen, consisting of two
parameters - IF PLL and AGC.
The first parameter is automatically adjusted.
AGC to adjust the setting on the TV antenna input test signal is fed "color bars"
frequency of 475.25 MHz and amplitude 10 mV. To control the adjustment to the pin. A tuner connected in 1000
digital voltmeter. Then adjust the value of AGC (factory default - 28), ensuring
voltmeter in the range 2.3 ... 3.8 V. To save the new value
return to the main menu using the MENU button and then switch the TV to standby mode.[b] White Balance
In the WHITE TONE sub menu can be adjusted cutoff point cathode tube. It is available
adjust your NORMAL RED, NORMAL GREEN and NORMAL BLUE. The factory settings are
40 (corresponds to the color temperature of 9600 K).
Adjusting the geometry of the
To adjust the image geometry to the antenna input of TV test signal is fed "mesh
field "in the color system PAL / SECAM frequency of 475.25 MHz and a sweep of 1 mV.
Sets the image NATURAL, enter the service mode SDAM and it will activate the line
GEOMETRY. The options available in this submenu, and their default values ​​listed in Table. 2.
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]


عدل سابقا من قبل أشرف عثمان في الخميس يوليو 21, 2011 8:58 am عدل 1 مرات
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس شامل أجهزة service-mode PHILIPS   الخميس يوليو 21, 2011 8:16 am

Adjusting the sound path
In sub AUDIO available to adjust two parameters:

  • AF-M - the sound quality setting, the default is 300;
  • A2T - setting the threshold decoder standard A2, the default is 25._
PHILIPS G88 chassis.
select 'sound only' mode

  • Press' teletext'i 'feature' for 1 second
  • off hotel mode menu that appears.
PHILIPS CHASSIS GR2.2AA.
25PT400/42, 25PT410A/42, 28PT400A/42, 28PT450A/42 ..
CPU TMP47C1637. Enter the service mode as follows. Jumper contacts
M33 and M34 (service), and pressing the INSTALL on the front panel turn on the power switch.
You should see a message SER. To exit the service please click on the button
STANDBY. Also in these models is the service menu. Activated by pressing VOL +, and then
at the same time by pressing P +. In the second variant values ​​are stored at once. Go to
Hotel mode is as follows. Turn on the TV channel 38 and at the same time
Press VOL-, P-on the front of the TV.
PHILIPS CHASSIS L6, an AA.
14PT-1342 \ 43, 14PT-1352 \ 00 \ 01 \ 05 \ 07 \ 11 \ 39, 14PT-1542 \ 01 \ 43, 14PT-
1552 \ 00 \ 01 \ 05 \ 11, 20PT-1342 \ 43, 20PT-1542 \ 43, 21PT-1532 \ 58, 21PT-1542 \ 43, 37TA-1232 \ 03,
37TA1432 \ 03, 37TA1462 \ 18, 37TA1473 \ 18, 52TB-2452 \ 19, M-2052 \ 00 \ 01, M2152 \ 00 \ 07 \ 15
M2182 \ 00, M2192 \ 05: There are 2 ways of entering the service. 1.Zakorotit contacts S1 S2 on the processor
(Pin 14 IC7600). 2.C using the service control model RC7150 pressing buttons on it DEFAULT
or ALIGN. Exit from service: click on the button STAN-BY.
PHILIPS CHASSIS L6, an AA.
14PT-1342 \ 43, 14PT-1352 \ 00 \ 01 \ 05 \ 07 \ 11 \ 39, 14PT-1542 \ 01 \ 43
14PT-1552 \ 00 \ 01 \ 05 \ 11, 20PT-1342 \ 43, 20PT-1542 \ 43, 21PT-1532 \ 58, 21PT-1542 \ 43, 37TA-1232 \ 03,
37TA1432 \ 03, 37TA1462 \ 18, 37TA1473 \ 18, 52TB-2452 \ 19, M-2052 \ 00 \ 01, M2152 \ 00 \ 07 \ 15, M2182 \ 00, M2192 \ 05:
There are 2 ways of entering the service. 1.Zakorotit contacts S1 S2 on the processor (pin 14 IC7600).
2.C using the service control model RC7150 pressing buttons on it DEFAULT or ALIGN. Exit
service: click on the button STAN-BY.
PHILIPS CHASSIS L6.2. 25PT4423.
Full-time remote control off. in Dej. mode, then off.
power when the LED goes enable network simultaneously holding down the button text on the remote.



عدل سابقا من قبل أشرف عثمان في الخميس يوليو 21, 2011 8:59 am عدل 1 مرات
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس شامل أجهزة service-mode PHILIPS   الخميس يوليو 21, 2011 8:17 am

PHILIPS CHASSIS L6.2AA. 25PT4103/60.
Close the control points, "0053" and "0054"
near the processor. Exit: (STANBY).
PHILIPS CHASSIS L7, 1A \ AA.
14PT-118A \ 50B \ 67R \ 94R, 14PT132A \ 50B \ 50R \ 75R, 14PT133A \ 162R,
14PT137A \ 162R, 14PT138A \ 54R \ 58T \ 67R \ 71R \ 74R \ 75R \ 93S,
20PT188A \ 50B \ 67R \ 73R, 20PT120A \ 78R, 20PT132A \ 75R,
20PT137A \ 62R, 20PT138A \ 50D \ 58R \ 58H \ 58R \ 67R \ 71R \ 73R \ 74R \ 75R \ 94R \ 97R. CHASSIS
L7, 1A \ AA: Short-circuit contacts M24 and M25 on the circuit board (PCB). Output from the service click on the button
STAN-BY. Attention error buffer is cleared!
PHILIPS CHASSIS L7.2A. 21PT2622/69R.
Momentarily jumper M28 service points
and M29 (weight). Exit: STAND-BY
PHILIPS CHASSIS L9.1E. 14RT2665/00, 21PT1354/58C, 21PT1654/58.
Log into the service
Display (mode SDM): (0) (6) (2) (5) (9) (6) (MENU);
continue to enter the geometry (mode SAM) by simultaneously pressing "VOL -" and "PR -" panel TV.
Attention! SDM function in AS OFF does not include, and then (perhaps) your TV will stop working.
Exit: (STANBY).
The service menu TV:
Manufacturer: "Philips"
Model: 21PT1354/58C
Log into the service menu (mode SDM): "0" "6" "2" "5" "9" "6" "Menu";
continue to enter the geometry (mode SAM) by simultaneously pressing
"VOL -" and "PR -" panel TV.
Processor: SAA5542
Exit: STAND-BY
Chassis: L9.2E
PHILIPS CHASSIS MD1.2/AA /.
21PT440B, 21PT441B/02B, 21PT442B, 21PT4303, 21PT4422,
24PW6302,
24PW6322, 25PT5403, 25PT45, 25PT4523, 25PT5302, 25PT5322, 25PT5403, 25PT5423, 25PT6322,
25PT4503, 52TA4311. Processors TMP87CM36, TMP87CM38N. To enter the service mode
use the remote type RC7150. With this remote TV can be transformed into two modes.
A service mode by default SDM (button DEFAULT). In default mode, you can also enter through
contact closure S42 S43 on SSP (small signal panel). To exit, press
(Stand-by) (error buffer is cleared.) 2 Service tuning mode SAM. Log in SAM mode
accomplished by sending commands by pressing keys ALING
(MENU) and (-). After entering the menu you'll see a picture like Figure 1.
To exit, use the button (Stand-by) for errors can be monitored by the LED on
front of the TV. The list of error codes in the table.
0 No error ---------------------- ---------
1 Error BIMOS - (TDA8366) - 1 flash - IC7119 (SSP)
2 Error MSP3400/3410 - - 2 flashes - IC7353 (SSP)
3 Error bus I2C - 3 flashes - All components on the I2C bus
4 Not a ROM (EEROM) I2C - 4 flashes - IC7685 (SSP)
Faulty ROM 5 - (EEROM) - 5 blinks - IC7685 (SSP)
6 Error tuner - 6 flashes - U1000 (SSP)
7 Error Teletext TXT - 7 flashes - IC7702 (SSP)
8 Error Processor - Histogram - 8 flashes - IC7210 (reserve)
9 Error CPU - 16:9 - 9 flashes - IC7440 (module 16:9)
10 Error module WSSB - 10 flashes - IC7540 (module WSSB)
11 Error Processor - Dolby - 11 flashes - IC7600 (audio module)



عدل سابقا من قبل أشرف عثمان في الخميس يوليو 21, 2011 9:00 am عدل 1 مرات
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس شامل أجهزة service-mode PHILIPS   الخميس يوليو 21, 2011 8:19 am

PHILIPS CHASSIS MD2.11/12/13.
Log in via a special menu
Remote RC7150.
PHILIPS CHASSIS MD2.22 E. 25PT8303.
Simultaneously press (?) And (SLEEP) under
cover. . Exit: POWER OFF.
PHILIPS CHASSIS MG3.1E. 28PW9525, 28PW8806, 28PT7306/58.
Type of control
combination. Then press (MENU) or (i +). Presented several options for the code combination.
(0) + (6) + (2) + (5) + (9) + (6)
(0) + (3) + (6) + (2) + (5) + (9) + (6)
(0) + (4) + (6) + (2) + (5) + (9) + (6)
(0) + (7) + (6) + (2) + (5) + (9) + (6)
(0) + (Cool + (6) + (2) + (5) + (9) + (6)
(0) + (3) + (6) + (5) + (9) + (6)
PHILIPS CHASSIS 3A. 17CE7630, 21CE7649/55/7590, 17CE7531/7650 247 771, 41CE8746.
Press the button (MONO) TV on the keyboard. Hold the switch on the TV with remote control. Exit: STAND-BY
PHILIPS 25PT4104/58.
first two modes of service SDM close to the chassis control
point GND and SDM
the second mode of SAM. dial on the keypad, without pauses, 062 596 [+] button on the OSD
PHILIPS 28PT4456/00.
To enter the service mode to close contacts GND
and SMD servise mode, turn on the TV to the network, and 5. .. 15 to open contacts
PHILIPS 25PT8303
Log in at the same time press the "?" and "sleep" under the hood.
PHILIPS video recorder EPSILON.
To enter the service mode to hold
PLAY button on the (TV) press (STOP) on the remote control
PHILIPS 14PV100/01, 14PV505/58.
Enter the service mode is carried out from
standby.
Requires simultaneous key press (PLAY) on the TV and press (STOP) on the remote control
at the same time hold for about 10 seconds.
PHILIPS 28PT4456/00.
Log in to close the service contact: (GND) and (SMD -
servise mode) and turn on the TV to the network after 5-15 seconds and open contacts.
* * *
TV PHILIPS 14pt1548/01
TE1.1E Shassis,
Multi-system apparatus. Ingredients: Processor TDA 9351
PS/N3/2/1692 p1 PRX 47 CE 3224 TELRA_ P14, Memory: 24WC16L. TDKS: 1142 7027A.
Entering the service menu: With the remote control to dial 06,
wait a pause 2c, 25 to wait for a pause, a pause to wait for 96, I +.
* * *
TV PHILIPS 21PT5307/60,
Chassis S L01.1A AC. Processor -TDA9552H/N1/3I/1410,
fourth line-L01AT61.1, pamyat24S16WP.
Entering the service menu: SDM: 062 596 MENU / SAM: 062 596 OSD / STATUS. Sound - multi.
Secam - there. Russian language there is.
* * *


عدل سابقا من قبل أشرف عثمان في الخميس يوليو 21, 2011 9:03 am عدل 1 مرات
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس شامل أجهزة service-mode PHILIPS   الخميس يوليو 21, 2011 8:21 am

TV PHILIPS 28PT4456/00
CPU SAA5564PS/M3/0/81
VIDEO TDA8843 S1 --- PAL
Substitution of the TDA8844 S1 --- PAL / SECAM
TEXT MICRONAS MSP34150B3
Log in to close the service contact: (GND) and (SMD-servise mode) and turn on the TV in the network
after 5-15 seconds of open contacts.
* * *
MG2.1E AA
closure of the connector pin 2,3 0356 entered the Service default
closure of the connector pin 2,1 0356 entered into Service mode
PHILIPS 25PT8303 (S7E)
Login: simultaneously press "?" and "sleep" under the hood.
Service mode TV PHILIPS chassis L01.1E AA
TV chassis firms PHILIPS L01, IE AA has already been discussed in the pages of our magazine
(See "Repair & Service», № 10. 2004). Continuing the theme of service we offer to meet
mode of the chassis and to learn its hardware and software adjustments.
TV sets, collected on the chassis L01.1E AA can be transferred to the following service faces.

  • leveling service mode by default (SDAM);
  • client service mode (CSM).
Service mode SDAM is for the following purposes;
• Creation of Sun's i poem-settings of all nodes chassis for measurement and electrical
configuration chassis
• blocking protection scheme,
• Start up procedures blinking LED for troubleshooting;
• installation options;
• Displaying / clearing codes buffer errors;
• alignment settings. Service mode adjustments for C. SM chassis is not used and its options
read-only.
Service mode SDAM sets mode to the TV:

  • on top of the screen displays the message «S»;
  • frequency of reception station with antenna input of 475.25 MHz;
  • color system is SECAM L for France or PAL BG to other Western European countries;
  • volume is set at 25% of the maximum value, other values
sound and image - at 50%.
In the 5DAM blocked following modes: sleep timer, parental lock, blue background, hotel
auto-shutdown (when no video signal IDENT for 15 minutes), skipping unwanted channels
Autosave preferences.
To enter the service mode SDAM on the main board close the chassis between a bridge 9631
and 9641, then include the TV switch. Once displayed on the screen
image (Fig. 1), opens the connection between the bridges 9631 and 9641
Note. It must be borne in mind that when the jumper is closed 9631 and 9641, off
short-circuit protection circuit in 8 B.
Fig. One of the following symbols mean;
LLLL - counter hours of operation;
AAABCD XY - the software version number,
S - service mode indication SDAM;
ERR - error buffer that stores the last five error codes;
XXX-bytes of options;
CLEAR - resets the buffer errors (to reset, select this line and press
cursor button "right");
OPTIONS - sub set of bytes of options;
Bank - Activate (1) or off (0) control scheme of dark current radiation tube;
TUNER - Tuner Settings sub-menu;
WHITE TONE - a white balance adjustment,
GEOMETRY - sub control image geometry;
AUDIO - adjust the audio settings submenu
To navigate the service menu using the cursor buttons SDAM remote control "up / down." Selected
line becomes brighter. Activate the selected submenu (set values) is
by pressing cursor button remote control "to the left / right"
If the mode button SDAM MEMJ, you can go to the menu the user (usual menu for
parameter settings). To return to the SDAM press the OSD / STATUS on the remote. For
return from the sub A previous menu press the MENU button on the remote.
To save settings, service mode, press the SDAM STANDBY button on the remote.
Consider the hardware and software control chassis L01.1E AA.
Hardware control chassis LOI.IE AA
Adjust the accelerating voltage Vg2
1. Activate the service mode and it SDAM selected sub WHITE TONE.
2. Set values ​​NORMAL RED, GREEN and BLUE is 40.
3. Using the MENU button returns the user menu and set the minimum
Contrast and brightness (the image was barely visible OSD).
4. Returns to SDAM by pressing MENU.
5. Connected to the antenna input of the TV test signal generator and signal
"Dimensional field." The length adjustment control connected oscilloscope (1:10,0,2 ms / div) to one
from the cathode tube.
6. Variable resistor Screen (bottom to TDKS) set a constant voltage of
zero level to blanking (horizontal row blanking area)
equal to 160 ± 4 V
Adjustment of the focusing voltage
1 is connected to the antenna input of the TV test signal generator and signal "grid".
2. Press the SMART PICTURE on the remote control mode is selected the image or NATURAL MOVIES.
3 variable resistor Focus (top to TDKS) for optimum focus throughout
display area.



عدل سابقا من قبل أشرف عثمان في الخميس يوليو 21, 2011 9:06 am عدل 1 مرات
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس شامل أجهزة service-mode PHILIPS   الخميس يوليو 21, 2011 8:23 am

Software control chassis L01.1E AA
These adjustments do in the service mode SDAM. These include:
• Installation of bytes of options (sub OPTIONS);
• Control Toner (sub TUNER);
• White Balance Adjustment (sub menu WHITE TONE);
• Control of the geometry (sub GEOMETRY);
• Control audio track (sub AUDIO).
Set byte options
Enter the service mode and it SDAM select and activate row OPTIONS. You should
image to appear (Fig. 2).
Altogether there are seven bytes of options OP1 to OP7 Setting these bytes to configure
configuration of a specific model tuner type, region, sound processor modes, possible
broadcasting system, preset and SMART PICTURE SMART SOUND, stereo / mono, etc. Table
1 shows the fixed values ​​of the bytes of options for different models of TVs. Required
byte values ​​of options set with the cursor keys "left / right" on the remote. New
values ​​are stored after the previous menu
Adjusting the tuner
This adjustment is performed only after replacing the tuner chip non-volatile memory
7602. In service mode, activate the line SDAM TUNER. Appears on the screen submenu, consisting
of the two options - IF PLL and AGC.
OP1 OP2 model OPS OPS OP6 OP7 0R4
DVD 21R16807/01 216 247 249 184 208 54 3
DVD 21RT68O7/05 220 247 249 184 208 54 3
21RT 6807/58 DVD 216 247 249 184 208 54 0
24PW6817/01 DVD 216 24 / 263 184 208 54 3
24PW68T7/05 DVD 220 24 / 263 184 208 54 3
Para-Description 21RT6807 21RT6807 21RT6V07 24PW6817 24PW6817
Meters
/ 01 DVD / 05 DVD 58DVD / 01DVD / 05 DVD
HP parallelogram on hori-rolled 31 31 31 32 32
HB Parallelynos-b vertical lines 31 31 31 32 32
HSH Horizontal Shift 38 38 38 27 27
g-ww Horizontal Size 40 40 40 36 36
EWP Parabola horizontal 06 06 06 20 20
UCP distortion in the upper corners of the screen 35 35 35 20 20
LCP distortion in the lower corners 35 35 35 25 25
EWT Trapeze Horizontal
Combining centers IMAGE 35 35 35 28 28
VSL expressions and the screen vertically 36 36 36 37 37
VAM Vertical Size 63 63 63 30 30
VSC Vertical Linearity 23 23 23 20 20
VSH Vertical Shift 31 31 31 31 31
The increase in the VX vergikagi 25 25 25 25 25
N60 Horizontal Shift for 60 Hz 09 09 09 09 09
V60 Size 1 on the vertical to 60 Hz 64 64 64 64 64
[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
The first parameter is automatically adjusted.
AGC to adjust the setting on the TV antenna input test signal is fed "color bars"
frequency of 475.25 MHz and amplitude 10 mV. To control the adjustment to the pin. A tuner connected in 1000
digital voltmeter. Then adjust the value of AGC (factory default 28), seeking
voltmeter in the range 2,3.3,8 B. To save the new value back to the ground
menu using the MENU button and then switch the TV to standby mode.



عدل سابقا من قبل أشرف عثمان في الخميس يوليو 21, 2011 9:06 am عدل 1 مرات
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس شامل أجهزة service-mode PHILIPS   الخميس يوليو 21, 2011 8:27 am

White Balance
In the WHITE TONE sub menu can be adjusted cutoff point cathode tube Dov. It is available
adjust your NORMAL RED, NORMAL GREEN and NORMAL BLUE. Factory settings
equal to 40 (corresponds to the color temperature of 9600 K round)
Adjusting the geometry of the
To adjust the image geometry to the antenna input of TV test signal is fed
"Reticular field" in the color system PAL / SE MAS frequency of 475.25 MHz and a sweep of 1 mV. Install
Picture Mode NATURAL, part of the service mode SDAM and it will activate the line GEOMETRY.
The options available in this submenu, and their default values ​​listed in Table 2
Adjusting the sound path
In sub AUDIO available to adjust two parameters:
• AF M - Set audio quality, the default is 300,
A2T - setting the threshold decoder standard A2, the default is 25.
Setting up your TV
On the concept and the boards are reference points for setting up and troubleshooting.
Waveforms at the control points (the TV show on Al. XI. Checkpoints
marked according to the functional units belonging to the TV:
A1-A19 - control points for a sound channel, C1-NW - reference points for the control unit
and the front panel;
F1-F5 - reference points for Vertical, 11-16 - IF checkpoints tract; L1-L10 -
control points for a line scan; P1-P7 - reference points for the power supply; S1-S4 -
reference points for timing chains, V1-V16 - reference points for the video and
board tube.
TV can be found in the following service modes:
• Service mode by default;
• service mode configuration;
• service user mode.
Consider a more detailed discussion of these modes.
(SDM)
Service mode by default
This mode is used for:
• Fault indication via LED on front panel;
• installation of control options,
• monitoring the buffer errors.
Enter the service mode by default:
• Service on the remote control RC7150 press the DEFAULT;
• for normal remote control press the MENU, and then enter the numeric sequence
062596;
• close the pin. 20 microprocessor 7600 to ground during the turn on the TV. After
turn on the TV jumper can be removed.
To exit the service mode by default switch the TV to standby mode. If you just
turn the power off after power on the TV again will be in service mode.
When power is turned off or exit the service mode, error buffer is cleared television.
When you install the service mode, the default control set to the following provisions:
• Color system PAL / SECAM,
• 475.25 MHz frequency of administration,
• Volume - 25%;
• Brightness, contrast, tone, etc. - 50%
• ignored the timer, the "blue background" auto-off, mode, "Hospital" and "Hotel"
The child lock, personal settings, missed or blocked channels.
In service mode, the default screen displays the following information (see figure):
SDM
TV LOCK
INSTALLATION
BRIGHTNESS
COLOUR
CONTRAST
• LLLL - while the TV in hexadecimal format;
• L90 Air Force XY - the name of the chassis and the software version number;
• SDM (Service Default Mode) - display the service mode by default;
• OP Value (Options Code) OB1 .. 0V7 - byte values ​​of options;
• ERR - the last five specific errors. But more numerical values ​​are left.
Button MENU UP (Pt-) and the MENU DOWN (P-) are used to select options, service mode, and
button MENU LEFT (VOL-) and the MENU RIGHT (VOL +) - to change the values ​​of options.
Service mode settings (SAM)
Service mode settings used to adjust the mode selector channel balance
white screen geometry settings and adjust the sound. To display the mode settings
designation SAM (Service Alignment Mode) in the upper right corner of the screen.
Log in configuration mode:
• Press ALIGN to service remote RC7150;
• simultaneously press the buttons CHANNEL DOWN and VOLUME DOWN on the keyboard at the TV
time when the TV is in service mode SDM. Pressing these keys will return
TV service mode SDM;
• Press the number buttons remote control in the following order: 062 596, then press the
OSD with the remote control.
Exit SAM is the same as the mode of SDM. When you exit the setup mode and turn-off
supply buffer error is not cleared. Save Values ​​option is when you exit the menu.
In service mode, the SAM are four menus (see below). The control buttons in this mode, such
same as for the SDM.
Menu Tuner (TUNER)
In this menu are regulated by the following parameters:
• IFPLL - phase-locked for PAL / SECAM systems, except SECAM LL ';
• IF_PLL POS - phase-locked SECAM LL ';
• IF_PLL OFFSET - the default is 48;
• AFW - setting the AFC;
• AGC - AGC setting;
• YD - the default is 12;
• CL - the default is 4;
• AFA - parameter is read-only;
• AFB - parameter is read-only.
The white balance menu (WHITE TONE)
In this menu are regulated by the following parameters:
• NORMAL RED - red channel gain;
• NORMAL GRE - Green Channel Gain Control;
• NORMAL BL - Blue channel gain control;
• DELTA COOL R - the black level canal in the red;
• DELTA COOL BL - the black level in the blue channel;
• DELTA COOL GRE - the black level in a channel of green;
• DELTA WARM R - Adjusts the amount of white in the red channel;
• DELTA WARM BL - Adjusts the amount of white in the blue channel;
• DELTA WARM GRE - Adjusts the amount of white in the green channel.



عدل سابقا من قبل أشرف عثمان في الخميس يوليو 21, 2011 9:08 am عدل 1 مرات
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس شامل أجهزة service-mode PHILIPS   الخميس يوليو 21, 2011 8:29 am

Sound menu
In this menu are regulated by the following parameters:
• AF-M - the default value is 232;
• AT - the default is 4;
• STEREO - The default value is 15;
• DUAL - the default is 12;
Menu options available in monaural.
Menu screen geometry correction
In this menu are regulated by the following parameters:
• SBL - official marker;
• VSL - the slope of the vertically;
• VAM - vertical size;
• VSH - vertical shift;
• HSH - shift horizontally;
• VSC - S-correction in the vertical
• N60 - the default is 10;
• V60 - the default is 12;
• EWC - distortion in the corners;
• EWT - trapeze;
• EWP - parabola;
• EWW - width.
Service user mode
This regime is a "read only" and is used to determine the status of the TV
(For example, to clarify some additional data). TV will switch to this
mode by simultaneously pressing and holding the MUTE button on the remote control buttons, and any
Control Panel (P +, P-, VOL +, VOL-) to the TV for 4 seconds. To exit
press any button except the P + and P-.
When you switch to a service user mode control are set to "normal"
position, some modes are ignored. After exit from Setup mode source
TV settings are returned to their original values
Potential problems
Error codes, which are fixed diagnostics TV

If no errors are random, then before repair, clean
buffer error (see service mode SDM) is also necessary to carefully examine the contents ofBuffer errors because some errors can be simply a consequence of other errors, and not Mr.
eispravnostyu. Error codes, their causes and methods of elimination are given in Table. 3.
Fault TV with the front panel LEDs
In the absence of an image on a TV screen buffer can be read error
using the indicator on the front. Upon entering the SDM mode the LED will flash a
number of times that corresponds to the last error number (see Table. 3).
With the service control panel you can read the contents of the buffer errors. For
second display error codes should be consistent on-press buttons DIAGNOSE, 2, OK,
third - DIAGNOSE, 3, OK, etc.
Repair line scan

Check for voltage at the capacitor 140 in 2551 (A1). If no voltage,
disconnect the coil 5551. Thus, the power circuit line scan will be disabled.
If the voltage appeared - faulty line scan. Possible reasons:
• faulty transistor 7460;
• defective components supporting the regime of the transistor 7461;
• There are no impulses from the lower pin. VPU 40 7250 (A4) to the terminal stages
line scan.
If the transistor 7460 a short circuit of the IP will be heard the characteristic clicking sound.
To determine which part of the line scan there was a refusal (the output stages sweep
or schema distortion correction), disconnect the jumper 9465 and will set up the jumper 9461.
In this case, the distortion correction off if raster appeared (with parabolic distortions)

  • faulty circuit correction. If no raster - a fault in the output stages of line scanning.
In TVs with 26 - and 29-inch CRT (non-standard equipment) no correction circuit.


عدل سابقا من قبل أشرف عثمان في الخميس يوليو 21, 2011 9:09 am عدل 1 مرات
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس شامل أجهزة service-mode PHILIPS   الخميس يوليو 21, 2011 8:30 am

Repair power source
Troubleshooting should start with checking the voltage on the capacitor 11.5 in 2561. If
voltage is not present, check fuse 1572 and diode 6560. If these elements are intact,transferred to the primary circuit verification IP.
Check the output bridge rectifier - capacitor voltage should be 2508
approximately 300 V. If the voltage is not present, check fuse and diode 1500
bridge 6505. If the fuse is blown - check out the key transistor 7518 for a short
circuit and resistor 3518 to the interruption. If the voltage is in the 300 - check the drive voltage
IC 7520 on pin. 1. It should be approximately 13 V.
If the voltage does not start - check for open resistors and a zener diode 3510 to 6510
short circuit.
If the voltage on pin 1 IC 7520 is - check the voltage on the oscilloscope pin. 9
transformer 5545. and serviceability of the resistor 3529 and diode 6540.
Check the signal at the gate of the transistor core 7Y8 (reference point P2). In the absence of
signal to the transistor test signal at the output chip 7520 (vyv. 3), and serviceability
resistor 3525 and diode 6514.
Stdbycon (b vyv. MP, out) • signal produced by the microprocessor in the transition to standbymode or in overheating protection. At this signal BG1 goes into standby mode. At
normal operation the pin. 6 MP High Voltage (3.3 V) Standby - low;
Power down (vyv. 69 megapixel, entry) - a signal produced by PD During normal operation, the signal has
level of 3.3 V. In standby mode, the signal changes its value with a frequency of 10 Hz, with
positive half-wave duration is 5 ms. At fault in the voltage circuits
+12 (MainAux) signal is low. Probe current in the resistor is 12 in 3564
(Block A1). When the current increases over a b ... 2 A trigger on the transistors 7564 and 7562
switches, opening the transistor 7561.


عدل سابقا من قبل أشرف عثمان في الخميس يوليو 21, 2011 9:11 am عدل 1 مرات
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس شامل أجهزة service-mode PHILIPS   الخميس يوليو 21, 2011 8:32 am

Tuner control circuit
Sel-IF-LL'M-trap (3 MP vyv., output) - a control signal for selecting the filter, corresponding
TV signal system
Low signal corresponds to:
Western Europe selected signals PAL B / G, I; SECAM L / L ';
Eastern Europe the choice of PAL B / G;
South-East Asia choose the NTSC signal M. The high level corresponds to: Western Europe the choice of systems SECAM L / L ', L'-NICAM;
Eastern Europe the choice of PAL D / K;
South-East Asia PAL B / G, D / K, I.
For Western Europe use different filters 1002 and 1004 in the chains of video processing and
Audio (QSSD - Quasi Split Sound Demodulation). Eastern Europe is used
a filter 1003 for both signals (intercarrier demodulation).
Events leading to the protective regime
Part of the events leading up to the TV to switch the protection mode, controlled by a microprocessor:
beam current limit - MP measures the current of the beam during retrace Vertical.
If the current exceeds 75 mA, the microprocessor will switch the power supply in standby mode;
Protection bus l * C - when determining fault in the bus power supply switch MP in standby mode. SERVICE MODE
To configure and troubleshoot service provides 3-mode the default mode
tuning mode and user mode. In addition, the TV repair is possible with
special interface to the computer (ComPair), which in this paper is not considered.
Service mode by default
This mode is used in the following cases:
• To set the TV mode, which provides values ​​of measured signals, given
herein;
• to reject the defense on a short-circuit
to display the fault code with the LEDs on the front panel.
When you switch the TV in service mode by default in the following settings:
• Frequency setting the tuner:

  • 475.25 MHz for PAL / SECAM; -61,25 MHz for NTSC;
• levels of brightness, contrast, saturation, tone - 50%;
• volume - 25%
• Modes are disabled, preventing adjustment: a timer, the protection of children, blue background
regime hospital / hotel, auto power off, your personal settings.
Enter the service mode by default may be implemented in two ways:
• Using the Remote enter the code 062 596 and then press the MENU;
• close the bridge 9631 and 9641 (close to ground pin. 73 MT), and then turn
special interface to the computer (ComPair), which in this paper is not considered.
Service mode by default
This mode is used in the following cases:
• To set the TV mode, which provides values ​​of measured signals, given
herein;
• to reject the defense on a short-circuit
to display the fault code with the LEDs on the front panel.
When you switch the TV in service mode by default in the following settings:
• Frequency setting the tuner:

  • 475.25 MHz for PAL / SECAM; -61,25 MHz for NTSC;
• levels of brightness, contrast, saturation, tone - 50%;
• volume - 25%
• Modes are disabled, preventing adjustment: a timer, the protection of children, blue background
regime hospital / hotel, auto power off, your personal settings.
Enter the service mode by default may be implemented in two ways:
• Using the Remote enter the code 062 596 and then press the MENU;
• close the bridge 9631 and 9641 (close to ground pin. 73 MT), and then turn
food. After the power jumper can be removed.
Warning when set the jumper on the circuit ignores defense +8, which may
cause damage to the TV.
To display the service mode by default in the upper right corner of the screen
Message SDM (service default mode), and at the bottom - the last five errors reported.
To switch between the service mode menu and regular menu using the button MENU. Button
OSD / STATUS shows / hides the buffer errors. To enter the service mode by default
Present-service mode Royko need to hold down the VOL-UME_DOWN and CHANNELDOWN on
front of the TV for a few seconds. To exit the service mode
to switch the TV to standby mode. If you simply turn the power off, then
TV power will again be in the service regime. When you exit the service mode
Buffer error is cleared.


عدل سابقا من قبل أشرف عثمان في الخميس يوليو 21, 2011 9:12 am عدل 1 مرات
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس شامل أجهزة service-mode PHILIPS   الخميس يوليو 21, 2011 8:35 am

Service mode settings
To enter the service mode settings to the remote control to enter the code 062 596 and then pressOSD / STATUS. In the service mode settings on the TV screen displays the following information:
LLLL - while the TV to watch, while in standby mode is not considered;
AAA - the chassis number (L01);
In the - region (E - Europe, A - South-East Asia, U - North Africa, L - Latin America);
C - options (D - DVD, F - Full Text, M - mono, T - a text page);
D - number of language;
X - major version number,
Y - the minor version number;
SAM (Service alignment mode) - display the service mode settings;
ERR XX - codes of detected errors, mistakes later located to the left;
XXX - seven option codes;
CLEAR - erasing error codes. To erase press the cursor right;
AKV (auto kmc bias) - auto black level offset (0 - disabled 1 - enabled);
TUNER - setting the tuner;
WHITE TONE - setup shades of white;
GEOMETRY - correction of the raster
AUDIO - sound system
Navigation through the menus and the choice of values ​​made with the cursor. For
out of service mode to switch the TV to standby mode
Service user mode
This regime is a "read only" and is used to determine the status of the TV
(For example, in the case of telephone conversations with the service). Tele-divisor goes into this
mode by simultaneously holding the MUTE button on the remote or any button on the front
TV for 4 seconds. To turn the mode you press any button on the remote control, but
buttons select the channel or adjust the sound.
Fault TV with the LED on the front of the TV
In the absence of an image on a TV screen buffer can be read error
by LEDs on the front panel. Upon entering the SDM mode LED will show
buffer errors, in which:
• long pulse (750 ms) corresponds to the tens;
• between tens and ones pause - 1.5 s;
• short pulses correspond to the units;
• pause between error codes - 3;
• After the display of all the errors on the LED turns 3 and the procedure repeated.
In the case of finding the TV in Safe Mode LED will flash at 3 Hz.
Typical fault the TV and how to resolve them
TV will not turn on the power supply produces intermittent sound
• Unplug the coil 5561 (A1). If the sounds of the BP stop - a problem with supply chain
channel 95 in the (Main Supply). The most likely cause - faulty output stage
Horizontal Scan (A2.7402).
• Check the signal Stdby con - for the protection of overload and in standby mode signal has
low level, and during normal operation - high (3.3 V), as well as the serviceability of the optocoupler 7515 (A1).
TV will not turn on, strange sound is heard
Check the voltage on the pin. 8 IC 7520 (A1) - it should be about 300 V.
If the voltage is normal, check the circuit output signal converter: pin. 6 7520 -
3523 resistor-transistor gate 7521.Warning: the measurements at the gate of the transistor 7521 to be careful.
Prior to the measurement instrument grounded. The measuring instrument must have a high
input resistance.
The power supply produces intermittent sounds through 8 off

The LED on the front panel displays an error code 5. Because this error occurs when
Reset error signal and in the protection of the chain 8 in, first check the voltage of 8 V. If
it is absent, the test transistor and Zener 7408 6420 (A2).
The image on the screen - only the bottom half
Sound normal, error code 3. Check the voltage ± 13 V at the amplifier 7471 (A3). If
voltage is normal, then check the transmission chain of the sawtooth voltage generator:
pin. 16.17 MP - resistors 3244.3249 (A6) - resistors 3474,3479 (A3) - pin. 7.1 amp 7471.



عدل سابقا من قبل أشرف عثمان في الخميس يوليو 21, 2011 9:24 am عدل 1 مرات
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس شامل أجهزة service-mode PHILIPS   الخميس يوليو 21, 2011 8:36 am

No one color or one dominated by the image of the primary colors
Check for RGB signals on the pin. 56-58 MT. Check the appropriate chain of transmission signal through a tube amplifier on the motherboard to the cathode. If there is no signal on the cathode
CRT tube is removed from the base fee if the amplifier output signal appeared -
defective picture tube.
On the TV there is video noise
The menu is displayed correctly. Error code 11 - not working tuner (1000). Check the voltage
power to the pin. Tuner: +5 V on pin. 6 and 7, in 34 - to pin. 9 (VT Supply). In the absence of
In 34 voltage test circuit: a diode 6423 - resistors 3428, 3427 (A2) - Zener 6001 (A4).
Black and white image on the screen, the sound is distorted or missing
Incorrectly installed color. Press MENU, INSTALL, MANUAL STORE correct
value SYSTEM.
The image is too bright or too dark
Switch to service mode by default, or press the SMART PICTURE button on the remote.
Adjust the brightness / contrast. New personal settings are stored automa
White lines around the text or image
Exaggerated sharpness (SHARPNESS). Switch to service mode by default, or press
button on the remote SWART PICTURE regulate and clarity. New personal settings are stored
automatically.
No sound
11roperyayut passing through the composite video filters 1003 (1004), the presence of sound
stereo - to pin. 33 and the mono signal to the pin. 48 MT. Check the nutrition UMZCH
7901 (7902), the potential on line Volume_Mute, suitable to the amplifier.
* * *


عدل سابقا من قبل أشرف عثمان في الخميس يوليو 21, 2011 9:29 am عدل 1 مرات
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس شامل أجهزة service-mode PHILIPS   الخميس يوليو 21, 2011 8:38 am

Philips TV video recorder
14PV112/01,
14PV111/01, 14PV415/01, 14PV203/01, 14PV460/01. TV-VCR 2002-14 "Range (Z11) Chassis.
Enter the menu service: Within 5 seconds, push STAND / BY, then the code 2,7,1, MUTE, and finally STAND / BY.
* * *
TV video recorder Philips 14PV425/07, 14PV225/01.
Z12 Chassis.
Enter the service mode -
There are two options:
Option One:
Enter mode service marks of standby. Necessary
synchronous button (PLAY) button on the TV and (STOP) on the remote control, hold in this case about 10 seconds.
Option Two
entry into service mode: 2-7-1 button and mute in the course of 5 seconds. Entering the options button STATUS / EXIT,
Then reset the program PAUSE and 5 options to change. Exit from service STANDBY
Options to install 0179.
* * *
Plasma TV PIONEER PDP-434PE
with the receiver in the PIONEER PDP-R04E.
After removal of the cover panel on the receiver both lights are lit.
Enter the service mode: press info on the remote, after four seconds. to
the left, then up, then left, then right, and finally the power on.
Movement on the menu: mute. Reach the sub initialization - final setup-yes-enter.
Not forgotten then HDMI on exhibit.
* * *
TV Pioneer PDP-503PE (HDE) plasma.
Enter the service mode - press the button, Enter, info, 0. Repeatedly in the TV stand.
* * *
TV POLAR,
chassis S0807T, Processor
TDA9351PS/N2/2I1475 UOC POLAR 3.0, tuner KSH146EA, memory 24C08W6, SEKAM, DK
Entering the service menu: on-chip remote conclusions 3010 3 +9 and 1 +15. Exit: TV.
* * *
TV POLAR 54CTV4435,
CPU
TDA9351PS/N2/2I1475, brains 24C08, SECAM. PAL, tyunerKS-H-146EA
Entering the service menu: push the status, then the menu, and then myute and last stendbay.
Exit button av / tv.
* * *
TV POLAR CE-5427
PROCESSOR 8821CPNG4N30.
in the settings menu is not included, as the number buttons 0-9ne work.
of all the firmware, try me, normally not one came.
Entering the service menu (vol-) + (displey) on the remote.
After a brief experiment with a programmer figured out the location of cells for LOCK OFF and PASS OFF charge.
this cell 005 and 083 respectively, password nahoditsyav cell 024C, 024D, 024E.

* * *
TV POLAR 5101, 3701, 5401.
Entering the service menu: TV mode to transfer duty, the RC0201 remote press MUTE button and turn on TV mode working.
Removal of the castle:
If the code is forgotten, in the menu "Function" mode "Lock" to choose and three seconds to hold the button «X» in the remote control. Mode "Lock" to OFF switch.
* * *
TV POLAR 54CTV4029. S07shassi.
Control processor TDA 9381 P.4.0. Enter the service mode:
On board the remote user in m / c IC1 bridged pins 3 and 9, 1 and 15, respectively.
* * *


عدل سابقا من قبل أشرف عثمان في الخميس يوليو 21, 2011 9:31 am عدل 1 مرات
الرجوع الى أعلى الصفحة اذهب الى الأسفل
أشرف عثمان
المدير العام
المدير العام


عدد المساهمات : 2369
تاريخ التسجيل : 16/06/2010
العمر : 56

مُساهمةموضوع: رد: سرفس شامل أجهزة service-mode PHILIPS   الخميس يوليو 21, 2011 8:40 am

TV PRIMA M2153.
Composition of the board - processor TDA9381PS/N3/2/1831 CE6691 PIT36,
Manpower chip-STV9302, Tuner - LINGHUA BXATB138 ---- S TDL-3N4G, Shim - 5Q0765RT, ULF - AN17821A,
Fee for ROLSEN looks like a menu styled LG. Similar inscriptions on the chassis number is not found on board.
entry into the service menu with the remote user: push
button [MENU], on-screen menu "Image" will appear. Push
digital buttons [6], then [4], then [8] and [3] on the remote.
To service menu M1 ~ M4 enter, push digital
corresponding buttons on the remote. To enter the service
M5 ~ M0, press the button to be first [CALL] to exit from the M1-M4
menu, the letter M appears on the screen, then click successively
button [LOCK] (Figure suitcase with a handle) and one of the buttons digital
[5] ... [9] or [0] to enter the menu M5 ~ M0. If you're in some kind of
menu M5 ~ M0 are, then move to another menu can be carried out without pressing buttons [LOCK], but only digital buttons.
* * *
TV Rainford TV5564, PT92 chassis.
Processor TDA9351PS/N2/2I1185 TELRA, tyunerTEDE9-226A.
1. Enter the service mode: on the unit "V-" and on the control button
"for an hour three lines." Exit from the menu - Button TV.
If you change the memory in the television service by the first method
not included - from children locked buttons do not work on the panel,
even with the same firmware telly. To enter the service
need jumper KEYB output (№ 5) on the connector on SERVISE CONN
mass for one of the sek.Posle in to service memory
initsilizirovat, then you can go to the settings. In
episode, if not initialized memory, settings adjusted correctly is impossible.
* * *
الرجوع الى أعلى الصفحة اذهب الى الأسفل
 
سرفس شامل أجهزة service-mode PHILIPS
استعرض الموضوع السابق استعرض الموضوع التالي الرجوع الى أعلى الصفحة 
صفحة 1 من اصل 1

صلاحيات هذا المنتدى:لاتستطيع الرد على المواضيع في هذا المنتدى
أشرف عثمان للإلكترونيات :: قسم الصيانة - Repair-TV :: أرشيف السرفس -service-mode-
انتقل الى: